2004 MITSUBISHI ENDEAVOR lock

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
CIRCUIT OPERATION The PCM detects "CRUISE" (MAIN) switch "ON" signal to illuminate the
"CRUISE" indicator light on the combination meter. COMMENT Connector(s), wiring harness in the CAN bus line between the PCM and the
combination meter, power supply to the PCM, the combination meter, the PCM
may be defective. TROUBLESHOOTING HINTS
Malfunction of the combination meter Damaged harness, connector Malfunction of the PCM
DIAGNOSIS REQUIRED SPECIAL TOOL:
MB991958: Scan Tool (MUT-III Sub Assembly)
MB991824: V.C.I. MB991827: USB Cable MB991910: Main Harness A
STEP 1. Using scan tool MB991958, diagnose the CAN bus line.
Use scan tool MB991958 to diagnose the CAN bus lines.
1. Connect scan tool MB991958 to the data link connec
tor.
(Refer to AUTO
-
CAUTION: To prevent damage to scan tool MB991958,
always turn the ignition switch to the
"LOCK" (OFF) position before connecting or
disconnecting scan tool MB991958.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor

2. Turn the ignition switch to the "ON" position.
3. Diagnose the CAN bus line. (Refer to AUTO
-CRUISE CONTROL
SYSTEM DIAGNOSTIC TROUBLESHOOTING STRATEGY
, How
to diagnose CAN bus line).
4. Turn the ignition switch to the "LOCK" (OFF) position.
5. Disconnect scan tool MB991958.
Q: Is the check result satisfactory?
YES: Go to Step 2
NO: Repair the CAN bus lines. (Refer to DIAGNOSTIC TROUBLE
CODE DIAGNOSIS
). Then go to Step 4 .
STEP 2. Using scan tool MB991958, read the MFI diagnostic trouble code.
1. Connect scan tool MB991958 to the data link connector. (Refer to AUTO
-
CRUISE CONTROL SYSTEM DIAGNOSTIC TROUBLESHOOTING STRATEGY
).
CAUTION: To prevent damage to scan tool MB991958,
always turn the ignition switch to the
"LOCK" (OFF) position before connecting or
disconnecting scan tool MB991958.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA
.
2. Turn the ignition switch to the "ON" position.
3. Check for MFI system diagnostic trouble code. (Refer to HOW TO
READ AND ERASE DIAGNOSTIC TROUBLE CODE
).
4. Turn the ignition switch to the "LOCK" (OFF) position.
5. Disconnect scan tool MB991958.
Q: Is DTC U1108 set?
YES: Refer to DTC U1108: COMBINATION METER TIME
-OUT
.
Then go to Step 4 .
NO: Go to Step 3.
STEP 3. Retest the system.
Q: Does the "CRUISE" indicator light illuminate when the
"CRUISE" (MAIN) switch is turned "ON"?
YES: It can be assumed that this malfunction is intermittent (Refer to
HOW TO COPE WITH INTERMITTENT MALFUNCTIONS
).
NO: Replace the PCM [Refer to POWERTRAIN CONTROL
MODULE (PCM)
]. Then go to Step 4.
STEP 4. Retest the system.
Q: Does the "CRUISE" indicator light illuminate when the
"CRUISE" (MAIN) switch is turned "ON"?
YES: The procedure is complete.
NO: Return to Step 1 .
DATA LIST REFERENCE TABLE
CAUTION:
When shifting the selector lever to "D" range, the
brakes should be applied so that the vehicle
does not move forward.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor

Fig. 112: Checking Auto Cruise Control Switc
h
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Fig. 113: Identifying Switch Position And Specified Condition Table

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
AUTO-CRUISE CONTROL REMOVAL AND INSTALLATION
WARNING:Before removal of the air bag module, refer to AIR
BAG SAFETY PRECAUTIONS
and DRIVER
-SIDE AIR
BAG MODULE & CLOCKSPRING
.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Auto, Cruise Control System - Endeavor

2004 BODY & ACCESSORIES
Door - Endeavor
GENERAL DESCRIPTION OPERATION CENTRAL DOOR LOCKING SYSTEM The central door locking system operates the door lock actuator to lock or unlock
the doors and liftgate using the door lock switch built into the front power window
(main or sub) switch or key built into the driver's side door outside handle. The
system has the following operations and features:
All doors and liftgate can be locked using the door lock switch built into the
front power window (main or sub) switch. Insert the key into the driver's key cylinder and turn once to the unlock side to
unlock the driver's door. Turn the key once again to the unlock side to unlock
all doors and the liftgate. The key reminder function automatically unlocks all doors and liftgate when
door lock operation is performed and the front doors are opened while the key
is inserted into the ignition switch.
POWER WINDOWS When the power window (main or sub) switch is operated, the door windows will
open or close. This system has the following operations and features:
A power window lock switch on the power window main switch prevents the
door window glass from opening/closing with the front passenger's and rear
power window sub switch. The power window of the door window glass can be opened/closed for 30
seconds with the timer function after the ignition switch is turned OFF. (The
timer expires if the front door < LH or RH> is opened when the timer is in
operation). The power window main switch contains a one-touch down switch that will
automatically open the driver's side door window only.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor


2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

CENTRAL DOOR LOCKING SYSTEM DIAGNOSIS The central door locking system is controlled by the simplified wiring system
(SWS). Refer to SYMPTOM CHART
.
POWER WINDOW DIAGNOSIS The power window is controlled by the simplified wiring system (SWS). Refer to
SYMPTOM CHART
.
DOOR DIAGNOSIS INTRODUCTION TO GLASS AND DOOR DIAGNOSIS Glass and door faults include water leaks and improper opening and closing. Causes
for these faults can include faults in the glass, weatherstrip, drain hole, waterproof
film or door installation. GLASS AND DOOR DIAGNOSTIC TROUBLESHOOTING STRATEGY Use these steps to plan your diagnostic strategy. If you follow them carefully, you
will be sure that you have exhausted most of the possible ways to find a glass and
door fault.
1. Gather information from the customer.
2. Verify that the condition described by the customer exists.
3. Find the malfunction by following the Symptom Chart.
4. Verify malfunction is eliminated. SYMPTOM CHART SYMPTOM REFERENCE SYMPTOM
INSPECTION
PROCEDURE
REFERENCE PAGE
Water leak through door
window glass
1
INSPECTION
PROCEDURE 1: Water
Leak Throu
gh Door
Window Glass

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

STEP 2. Check for lock cable damage.
Q: Is the lock rod damaged?
YES: Repair or replace the lock cable, then go to Step 4 .
NO: Go to Step 3.
STEP 3. Check the door handle flexibility (amount of movement of handle
required to open door).
Q: Is the door handle flexibility good?
YES: Go to Step 4.
NO: Check the door outside handle and inside handle (Refer to DOOR
OUTSIDE HANDLE PLAY CHECK
and DOOR INSIDE HANDLE
PLAY CHECK
). Then go to Step 4.
STEP 4. Retest the system.
Q: Does the door open easily?
YES: The procedure is complete.
NO: Return to Step 1 .
INSPECTION PROCEDURE 6: Door Does Not Open or Close Completely DIAGNOSIS
STEP 1. Check the door hinge position.
Q: Is the door hinge correct?
YES: Go to Step 2.
NO: Adjust the door hinge (Refer to DOOR FIT ADJUSTMENT
).
Then go to Step 4 .
STEP 2. Check the door for damage.
Q: Is the door in
good condition?

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor

3. If the door is stiff to lock and unlock:
1. Adjustment by using the striker (toward the inside of the vehicle and
vertical direction)
Install an a
ppropriate bolt instead of the striker mountin
g bolt, and use
Fig. 8: Identifying Hinge Parts

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
2. Use a chisel or grinder to release the door hinge
mounting bolt washer, which is welded to the door
hinge.
3. On completion, paint the affected area with touch-up
paint to prevent corrosion.
4. Install the door hinge (Refer DOOR ASSEMBLY
).

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door - Endeavor