2001 TOYOTA SEQUOIA oil

SA175±05
F05063
SST
SST
F14312
SST
SST
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
SA±141
3137 Author: Date:
2005 SEQUOIA (RM1146U)
REPLACEMENT
1. Normal Type:
REMOVE BUSHING
Using SST and a press, remove the bushing.
SST 09710±14013 (09710±00061),
09710±28012 (09710±07031),
09950±70010 (09951±07100)
2. Normal Type:
INSTALL BUSHING
Using SST and a press, install a new bushing.
SST 09710±14013 (09710±00061),
09710±28012 (09710±07031),
09950±70010 (09951±07100)

SA176±04
SA±142
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
3138 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
Installation is in the reverse order of removal (See page SA±137).

± BRAKETROUBLESHOOTING
BR±3
3170 Author: Date:
2005 SEQUOIA (RM1146U) Hard pedal but brake inefficient
1. Fluid leaks for brake system
2. Air in brake system
3. Pad (Worn)
4. Pad (Cracked or distorted)
5. Pad (Oily)
6. Pad (Glazed)
7. Disc (Scored)
8. Vacuum leaks for booster systemDI±1059
BR±4
BR±24
BR±33
BR±24
BR±33
BR±24
BR±33
BR±24
BR±33
BR±30
BR±39
BR±21
Noise from brakes
1. Pad (Cracked or distorted)
2. Installation bolt (Loose)
3. Disc (Scored)
4. Pad support plate (Loose)
5. Sliding pin (Worn)
6. Pad (Dirty)
7. Pad (Glazed)
8. Tension or return spring (Faulty)
9. Anti±squeal shim (Damaged)
10.Shoe hold±down spring (Damaged)BR±24
BR±33
BR±27
BR±36
BR±30
BR±39
BR±33
BR±36
BR±24
BR±33
BR±24
BR±33
BR±42
BR±24
BR±33
BR±42

BR±26
± BRAKEFRONT BRAKE PAD
3193 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:
Apply disc brake grease to both sides of inner anti±squeal
shims (See page BR±24).
(d) Install new pads.
NOTICE:
Do not allow oil or grease to get on the rubbing face.
7. INSTALL ANTI±RATTLE SPRING AND 2 PINS
8. INSTALL CLIP
9. INSTALL FRONT WHEEL
Torque: 110 N´m (1,122 kgf´cm, 81 ft´lbf)
10. DEPRESS BRAKE PEDAL SEVERAL TIMES
11. CHECK THAT FLUID LEVEL IS AT MAX LINE

BR0TB±07
F13313
F13314
BR±34
± BRAKEREAR BRAKE PAD
3201 Author: Date:
2005 SEQUOIA (RM1146U)
REPLACEMENT
1. REMOVE REAR WHEEL
2. INSPECT PAD LINING THICKNESS
Check the pad thickness through the caliper inspection hole
and replace pads if not within the specification.
Minimum thickness: 1.0 mm (0.039 in.)
3. REMOVE BRAKE CALIPER
(a) Remove the 2 sliding pins.
(b) Remove the caliper and suspend it so the hose is not
stretched.
HINT:
Do not disconnect the flexible hose.
4. REMOVE 2 PADS WITH 2 ANTI±SQUEAL SHIMS
5. REMOVE 4 PAD SUPPORT PLATES
NOTICE:
The pad support plates can be used again provided that
they have sufficient rebound, no deformation, cracks or
wear, and have had all rust, dirt and foreign particles
cleaned off.
6. CHECK DISC THICKNESS AND RUNOUT
(See page BR±39)
7. INSTALL PAD SUPPORT PLATES
8. INSTALL NEW PADS
NOTICE:
When replacing worn pads, the anti±squeal shims must be
replaced together with the pads.
(a) Install the pad wear indicator plate on new inner pad.
(b) Install the anti±squeal shim on each pad.
(c) Install the inner pad with the pad wear indicator plate fac-
ing downward.
(d) Install outer pad.
NOTICE:
There should be no oil or grease adhering to the friction
surfaces of the pads or the disc.
9. INSTALL CALIPER
(a) Draw out a small amount of brake fluid from the reservoir.

F13254
INOUTAttachment
Pressure Feed Tube
SST
Z15498
Oil
Reservoir
PS Vane
Pump PS Gear
SST Closed
Z15499
Oil
Reservoir
PS Vane
Pump PS Gear
SST Open SR±6
± STEERINGPOWER STEERING FLUID
3233 Author: Date:
2005 SEQUOIA (RM1146U)
2. CHECK STEERING FLUID PRESSURE
(a) Remove the air cleaner assembly with the air cleaner
hose connected (See page SR±26).
(b) Disconnect the pressure feed tube from the PS vane
pump (See page SR±26).
(c) Connect SST, as shown in the illustration.
SST 09640±10010 (09641±01010, 09641±01030,
09641±01060)
NOTICE:
Check that the valve of the SST is in the open position.
(d) Bleed the power steering system (See page SR±4).
(e) Start the engine and run at idle.
(f) Turn the steering wheel from the lock position to the other
side of lock position several times to boost fluid tempera-
ture.
Fluid temperature: 80 °C (176 °F)
(g) With the engine idling, close the valve of the SST and ob-
serve the reading on the SST.
Minimum fluid pressure:
8,336 kPa (85 kgf/cm
2, 1,209 psi)
NOTICE:

Do not keep the valve closed for more than 10 se-
conds.

Do not let the fluid temperature become too high.
(h) With the engine idling, open the valve fully.
(i) Measure the fluid pressure at engine speeds of 1,000 rpm
and 3,000 rpm.
Difference in fluid pressure:
490 kPa (5 kgf/cm
2, 71 psi) or less
NOTICE:
Do not turn the steering wheel.

Z15500
Oil
Reservoir
PS Vane
Pump PS Gear
SST Open Lock Position
± STEERINGPOWER STEERING FLUID
SR±7
3234 Author: Date:
2005 SEQUOIA (RM1146U)
(j) With the engine idling and the valve fully opened, turn the
steering wheel left or right to the full lock position.
Minimum fluid pressure:
8,336 kPa (85 kgf/cm
2, 1,209 psi)
NOTICE:

Do not maintain the lock position for more than 10 se-
conds.

Do not let the fluid temperature become too high.
(k) Disconnect the SST.
SST 09640±10010 (09641±01010, 09641±01030,
09641±01060)
(l) Connect the pressure feed tube (See page SR±36).
(m) Install the air cleaner assembly with air cleaner hose (See
page SR±36).
(n) Bleed air from the power steering system
(See page SR±4).

F13256

Non±reusable part
Molybdenum disulfide lithium base grease
: Specified torqueN´m (kgf´cm, ft´lbf)Column Upper
Bracket
Key Cylinder Key Unlock
Warning Switch
Ignition Switch
10.5 (110, 8)
Column Tube
Assembly
2.2 (23, 19 in.´lbf)

Spring Guide


Tilt Spring Main Shaft Assembly Steering Column Housing
Tilt Lever Release Lever SpringTurn Signal Bracket

Compression
SpringSpring
Retainer Upper Bearing Inner Race Seat
Inner Race

12 (120, 9)
Pivot Pin
Spring
Park Lock Cable
Assembly
Shaft Bearing
Main Shaft Stopper
Pivot Pin Shift Lever
Housing
18 (180, 13)



Shift Lever
No. 2 Steering Column Ring

Tilt Lever Lock Shaft9.0 (90, 78 in.´lbf)





7.5 (75, 65 in.´lbf)
2.9 (29, 25 in.´lbf)
Transponder Key Coil
Key Cylinder
Lamp Assembly
Screw
Transponder Key Amplifier
Tilt No. 1
Stopper
± STEERINGTILT STEERING COLUMN
SR±13
3240 Author: Date:
2005 SEQUOIA (RM1146U)