2001 TOYOTA SEQUOIA maintenance reset

DICEL±02
± DIAGNOSTICSENGINE
DI±27
221 Author: Date:
2005 SEQUOIA (RM1146U)
READINESS MONITOR DRIVE PATTERN
1. PURPOSE OF THE READINESS TESTS

The On±Board Diagnostic (OBD II) system is designed to monitor the performance of emission±re-
lated components and report any detected abnormalities in the form of Diagnostic Trouble Codes
(DTCs). Since the various components need to be monitored during different driving conditions, the
OBD II system is designed to run separate monitoring programs called Readiness Monitors. Many
state Inspection and Maintenance (I/M) programs require that vehicles complete their Readiness Mon-
itors prior to beginning an emission test.

The current status of the Readiness Monitors can be seen by using the hand±held tester with version
9.0 software (or newer), or a generic OBD II Scan tool.

To view the Readiness Monitor status using the hand±held tester, select ºMonitor Statusº from the En-
hanced OBD II Menu.

A status of ºcompleteº indicates that the necessary conditions have been met to run the performance
tests for the related Readiness Monitor.

The Readiness Monitor will be reset to ºincompleteº if:

ECM has lost power (battery or fuse).

DTCs have been cleared.

The conditions for running the Readiness Monitor have not been met.

In the event that any Readiness Monitor shows ºincomplete,º follow the appropriate Readiness Monitor
Drive Pattern to activate the monitor and change the readiness status to ºcomplete.º
CAUTION:
Strictly observe the posted speed limits, traffic laws, and road conditions when performing these
drive patterns.
NOTICE:
These drive patterns represent the fastest method to satisfy all necessary conditions which allow
the specific readiness monitor to complete.
In the event that the drive pattern must be interrupted (possibly due to traffic conditions or other fac-
tors) the drive pattern can be resumed, and in most cases, the readiness monitor will still set to ºcom-
pleteº.
To ensure rapid completion of readiness monitors, avoid sudden changes in vehicle load and speed
(driving up and down hills and/or sudden acceleration).
Contents:
TITLESTEP(s)
CATALYST MONITOR2
EVAP MONITOR3, 4
AIR±FUEL RATIO (A/F) AND OXYGEN SENSOR (O2S) MONITOR5
OXYGEN SENOSR HEATER MONITOR6

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1609
1803 Author: Date:
2005 SEQUOIA (RM1146U)A/T R
Receives an R signal from the park/neutral position switch (Direct line)±
TAIL/HEADReceives a dimmer signal from the body ECU (BEAN)±
TIRE PRESSUREReceives a low tire pressure signal from the tire pressure monitor ECU (Direct line)
4LOReceives a 4LO signal from the 4WD control ECU (Direct line)±
MAIN REQD (Blinks)Blinks when 4,500 miles have been traveled, after ODO/TRIP switch is set (Direct
line)
MAIN REQD (Comes on)Blinks when 5,000 miles have been traveled, after ODO/TRIP switch is set (Direct
line)
RSCA OFFReceives an RSCA OFF signal from the airbag sensor center (Direct line)
HIReceives a suspension position HI signal from the suspension control ECU (Direct
line)
NReceives a suspension position N signal from the suspension control ECU (Direct
line)
LOReceives a suspension position LO signal from the suspension control ECU (Direct
line)
AHC MAN.Receives a suspension control manual signal from the suspension control ECU
(Direct line)
*1: w/ Day time running light
*2: w/o Day time running light
BUZZER:
ItemDetail
Key ReminderBuzzer is ON: Ignition switch is OFF, key is inserted, and door is open.
Fasten BeltBuzzer is ON: Ignition switch is ON and seat belt is unfastened.
2. COMBINATION METER IN SEQUOIA HAS THE FOLLOWING FEATURES:
(a) Built±in buzzer for the reminder system (key and seat belt)
(b) Integrated trip and odometer knobs

Press and release knob to scroll through trip ºAº, trip ºBº, and odometer features.

Press and hold the trip knob to reset trip meter functions.
(c) Oil maintenance indicator

When 4,500 miles have been traveled, after the ODO/TRIP switch is set, the maintenance indica-
tor begins to blink for 15 seconds after the ignition switch is turned to the ON position.

When 5,000 miles have been traveled, after the ODO/TRIP switch is set, the maintenance indica-
tor comes on.

Press and hold the trip knob to reset the oil maintenance indicator.
(d) Rotate knob to adjust interior illumination

± BODY ELECTRICALCOMBINATION METER
BE±59
3463 Author: Date:
2005 SEQUOIA (RM1146U)
15. INSPECT DRIVER'S SEAT BELT WARNING BUZZER
(a) Check warning buzzer function.
(1) Turn the ignition switch ON and check that the driver's seat belt warning buzzer sounds if the
driver 's seat belt is not fastened.
(2) Check that the buzzer stops after about 6 seconds.
16. INSPECT KEY REMINDER WARNING BUZZER
(a) Check warning buzzer function.
(1) Turn the ignition switch OFF and check that the key reminder warning buzzer sounds if the igni-
tion key is inserted into the key cylinder and the front driver side door is opened.
17. MAINTENANCE LIQUID RESETTING PROCEDURE
Indicator Condition:
StateConditionSpecified State
BlinkingThe vehicle has traveled 4,500 miles after the
previous settingThe indicator blinks for 12 seconds after the igni-
tion switch is turned on (including 3 seconds for a
valve check).
Continuously IlluminatedThe vehicle has traveled 5,000 miles after the
previous settingThe indicator is continuously illuminated after the
ignition switch is turned on.
(a) Set the display window to ODO.
(b) Turn the ignition switch off.
(c) Pressing the reset switch, turn the ignition switch to the ON position (keep pressing for at least 5 se-
conds).
(d) Reset procedure is completed.
HINT:

If the ignition switch is turned off during the reset procedure, reset mode is canceled.

If the reset switch is turned off during the reset procedure, reset mode is canceled and the display
shows the condition prior to the reset procedure.