2001 TOYOTA SEQUOIA oil

R13340
SST
Vinyl Tape
F14486
40 mm
(1.57 in.)
F14485
SST
F14522SST
SA2351
SST
± SUSPENSION AND AXLEREAR DIFFERENTIAL CARRIER
SA±127
3123 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Using SST and a plastic hammer, install the oil seal until
its surface is flush with the differential carrier end.
SST 09316±12010, 09649±17010
HINT:
Connect 2 SST with vinyl tape.
18. INSTALL COMPANION FLANGE
(a) Place the companion flange.
(b) Coat the threads of a new nut with hypoid gear oil.
(c) 2WD:
Torque the companion flange nut.
(1) Install the 3 stud bolts so that the heads come out
40 mm (1.57 in.).
(2) Set the SST and install the 3 nuts to the companion
flange.
SST 09213±58013
(3) Using SST to hold the flange, torque the nut.
SST 09330±00021
Torque: 147 N´m (1,500 kgf´cm, 109 ft´lbf)
(d) 4WD:
Using SST to hold the flange, torque the nut.
SST 09330±00021
Torque: 147 N´m (1,500 kgf´cm, 109 ft´lbf)

SA15R±13
± SUSPENSION AND AXLEREAR DIFFERENTIAL CARRIER
SA±129
3125 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
1. INSTALL DIFFERENTIAL CARRIER ASSEMBLY
(a) Install a new gasket.
(b) Install the differential carrier assembly with the 10 washers and nuts.
NOTICE:
Be careful not to damage the installation surface.
Torque: 73 N´m (740 kgf´cm, 54 ft´lbf)
2. CONNECT REAR PROPELLER SHAFT
2WD: See page PR±5
4WD: See page PR±9
3. INSTALL REAR AXLE SHAFTS (See page SA±102)
4. FILL DIFFERENTIAL WITH HYPOID GEAR OIL (See page SA±105)

SA2BG±02
F14308
58 (591, 43)
Cushion
Retainer
Insulator
Hollow
Spring
Shock Absorber

Bushing
N´m (kgf´cm, ft´lbf) : Specified torque

Non±reusable part
Coil
Spring




140 (1,428, 103)


RetainerCushion
Retainer
Retainer
Lateral Control Rod


Stabilizer Bar Link
87 (887, 64)
69 (704, 51)
Stabilizer Bar Link
69 (704, 51)
Normal Type:
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
SA±135
3131 Author: Date:
2005 SEQUOIA (RM1146U)
COIL SPRING AND REAR SHOCK ABSORBER
COMPONENTS

F16917
58 (591, 43)
Cushion
Insulator
Hollow
Spring
Shock Absorber
N´m (kgf´cm, ft´lbf) : Specified torque

Non±reusable part
Coil
Spring




140 (1,428, 103)


Retainer
Lateral Control Rod


Stabilizer Bar Link
87 (887, 64)
69 (704, 51)
Stabilizer Bar Link
69 (704, 51)
Cushion
Auto Leveler Type: SA±136
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
3132 Author: Date:
2005 SEQUOIA (RM1146U)

SA2BH±02
F14305
F14306
F16918
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
SA±137
3133 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
1. REMOVE REAR WHEELS
Torque: 110 N´m (1,150 kgf´cm, 83 ft´lbf)
2. SUPPORT REAR AXLE HOUSING WITH JACK
3. Normal Type:
REMOVE SHOCK ABSORBER
(a) Remove the bolt and disconnect the shock absorber from
the axle housing.
Torque: 87 N´m (887 kgf´cm, 64 ft´lbf)
(b) Use the same procedure described above to the other
side.
(c) While holding the piston rod, remove the nut, 2 retainers,
cushion and shock absorber.
Torque: 58 N´m (591 kgf´cm, 43 ft´lbf)
(d) Remove the 2 retainers and cushion from the shock ab-
sorber.
4. Auto Leveler Type:
REMOVE SHOCK ABSORBER
NOTICE:
When removing and installing of the shock absorber, per-
form the procedure with the shock absorber stretched
completely. The primary rod reaction force of the shock ab-
sorber is apploximately 1,000 N.
(a) Remove the bolt and disconnect the shock absorber from
the axle housing.
Torque: 87 N´m (887 kgf´cm, 64 ft´lbf)
(b) Use the same procedure described above to the other
side.

F16919
F16920
F14307
F04396
SA±138
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
3134 Author: Date:
2005 SEQUOIA (RM1146U)
(c) While holding the piston rod, remove the nut, retainer,
cushion and shock absorber.
Torque: 58 N´m (591 kgf´cm, 43 ft´lbf)
(d) Remove the retainer and cushion from the shock absorb-
er.
5. DISCONNECT LH AND RH STABILIZER BAR LINKS
Remove the 2 nuts and disconnect the LH and RH stabilizer bar
links.
Torque: 69 N´m (704 kgf´cm, 51 ft´lbf)
6. DISCONNECT LATERAL CONTROL ROD
Remove the nut, washer, bolt and disconnect the lateral control
rod.
Torque: 140 N´m (1,428 kgf´cm, 103 ft´lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the nut and bolt.
7. REMOVE COIL SPRING
(a) Lower the axle housing.
NOTICE:
Be careful not to snap the brake line and parking brake
cable.
(b) While lowering the axle housing, remove the coil spring,
hollow spring and insulator.
HINT:
At the time of installation, please refer to the following items.

Check that the coil spring end is installed correctly.

If the coil spring end is not in the correct position, reinstall
the coil spring.

SA174±05
SA0627
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
SA±139
3135 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
Normal Type:
INSPECT SHOCK ABSORBER
Compress and extend the shock absorber rod and check that
there is no abnormal resistance or unusual operation sounds.
If there is any abnormality, replace the shock absorber with a
new one.

SA2BI±02
W03120F07370
50 mm
(1.97 in.)30 mm
(1.18 in.)
F17130
50 mm (1.97 in.) High Pressure
Chamber Side:130 mm (5.12 in.)
F17131
Low Pressure
Chamber Side:50 mm (1.97 in.)
40 mm (1.57 in.) SA±140
± SUSPENSION AND AXLECOIL SPRING AND REAR SHOCK ABSORBER
3136 Author: Date:
2005 SEQUOIA (RM1146U)
DISPOSAL
1. FULLY EXTEND SHOCK ABSORBER ROD
2. Normal Type:
DRILL HOLE TO REMOVE GAS FROM CYLINDER
Using a drill, make a hole in the cylinder, as shown in the illustra-
tion to discharge the gas inside.
CAUTION:
The discharged gas is harmless, but be careful of chips
which may fly out when drilling.
3. Auto Leveler Type:
DRILL HOLE TO REMOVE GAS FROM CYLINDER
Using a drill, make a hole on the shaded area of the cylinder,
as shown in the illustration to discharge the gas inside.
CAUTION:

Be sure to perform the procedure in the order, the
high pressure chamber and the low pressure cham-
ber.

Wear protective goggles and cover the absorber with
a plastic bag or like when boring.

The discharged gas is harmless, but be careful of
chips which may fly out when drilling.