2001 TOYOTA SEQUOIA oil

BE25W±04
I21525
Free Pushed in
I18556
I04053
± BODY ELECTRICALSTOP LIGHT SYSTEM
BE±47
3451 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECT STOP LIGHT SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
Switch pin free1 ± 4Continuity
Switch pin pushed in1 ± 4No continuity
Switch pin free2 ± 3No continuity
Switch pin pushed in2 ± 3Continuity
If continuity is not as specified, replace the switch.
2. w/ Rear Spoiler:
INSPECT HI±MOUNTED STOP LIGHT ASSEMBLY
CONTINUITY
Using the ohmmeter, check that continuity exists between ter-
minal 1 and terminal 2.
If continuity is not as specified, replace the light assembly.
3. w/o Rear Spoiler:
INSPECT HI±MOUNTED STOP LIGHT ASSEMBLY
CONTINUITY
Using the ohmmeter, check that continuity exists between ter-
minal 1 and terminal 2.
If continuity is not as specified, replace the light assembly.

I01935
4 3
I01936
4 5
I01937
1
2
4 5
I18560
Front Washer Motor:
2
Rear Washer Motor:1
2
1
± BODY ELECTRICALWIPER AND WASHER SYSTEM
BE±51
3455 Author: Date:
2005 SEQUOIA (RM1146U)
6. High Speed:
INSPECT WIPER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 3 and
the negative (±) lead from the battery to the motor body or termi-
nal 4, and check that the motor operates at high speed.
If operation is not as specified, replace the motor.
7. Stopping at Stop Position:
INSPECT WIPER MOTOR OPERATION
(a) Operate the motor at low speed and stop the motor opera-
tion anywhere except at the stop position by disconnect-
ing positive (+) lead from terminal 5.
(b) Connect terminals 1 and 5.
(c) Connect the positive (+) lead from the battery to terminal
2 and the negative (±) lead from the battery to the motor
body or terminal 4, and check that the motor stops run-
ning at the stop position after the motor operates again.
If operation is not as specified, replace the motor.
8. INSPECT WASHER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 2 and
the negative (±) lead to terminal 1, and check that the motor op-
erates.
NOTICE:
These tests must be performed quickly (within 20 seconds)
to prevent the coil from burning out.
If operation is not as specified, replace the motor.

I21530
Ignition
Switch
Battery(Wire Harness Side)(3.4W) Fuel Gauge
Z05730
Warning Light
Ignition
Switch
Battery
1
23
45
Wire
Harness Side:
I28772
I01278
BE±56
± BODY ELECTRICALCOMBINATION METER
3460 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Connect terminals 2 and 3 on the wire harness side con-
nector through a 3.4 watts test bulb.
(d) Turn the ignition switch ON, check that the bulb comes on
and the receiver gauge needle moves towards the full
side.
HINT:
Because of silicon oil in the gauge, it will take a short time for
the needle to stabilize.
If operation is not as specified, inspect the receiver gauge resis-
tance.
4. INSPECT FUEL LEVEL WARNING LIGHT OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Connect terminals 2 and 3 on the wire harness side con-
nector.
(c) Turn the ignition switch ON and check that the warning
light comes on.
If the warning light does not come on, test the bulb or inspect
the wire harness.
5. INSPECT ENGINE COOLANT TEMPERATURE SEND-
ER GAUGE RESISTANCE
(a) Disconnect the engine coolant temperature sender
gauge.
(b) Measure the resistance between terminals 1 and 2 of the
connector according to the value(s) in the table below.
Temperature °C (°F)Resistance (W)
±20 (±4)13,840 to 16,330
20 (68)2,320 to 2,590
80 (176)310 to 326
110 (230)139.9 to 143.5
If resistance value is not as specified, replace the engine cool-
ant sender gauge.
6. INSPECT OIL PRESSURE SENDER OPERATION
(a) Disconnect the connector from the oil pressure sender.
(b) Check that no continuity exists between terminal and
ground with the engine stopped.
(c) Check that continuity exists between terminal and ground
with the engine running.
HINT:
Oil pressure should be over 24.5 kPa (0.25 kgf/cm
2, 3.55 psi).
If operation is not as specified, replace the oil pressure sender.

I05027
2
13 5
2 5
135
I01291
Tester Probe
Tin FoilHeat Wire
I01292
At Center
I01293
0 Volts
Broken
WireSeveral
Volts
Battery
Side Ground SideFoil Strip

 BE±66
± BODY ELECTRICALDEFOGGER SYSTEM
3470 Author: Date:
2005 SEQUOIA (RM1146U)
4. INSPECT MIRROR HEATER RELAY CONTINUITY
ConditionTester connectionSpecified condition
Always1 ± 2Continuity
Always3 ± 5No continuity
Apply B+ between
terminals 1 and 2.3 ± 5Continuity
If continuity is not as specified, replace the relay.
5. INSPECT DEFOGGER WIRE
NOTICE:

When cleaning the glass, use a soft, dry cloth, and
wipe the glass in the direction of the wire. Take care
not to damage the wires.

Do not use detergents or glass cleaners with abrasive
ingredients.

When measuring voltage, wrap a piece of tin foil
around the tip of the negative probe and press the foil
against the wire with your finger, as shown in the il-
lustration.
(a) Turn the ignition switch ON.
(b) Turn the defogger switch ON.
(c) Inspect the voltage at the center of each heat wire, as
shown.
VoltageCriteria
Approx. 5 VOkay (No break in wire)
Approx. 10 V or 0 VBroken wire
HINT:
If there is approximately 10 V, the wire is broken between the
center of the wire and the positive (+) end. If there is no voltage,
the wire is broken between the center of the wire and ground.
(d) Place the voltmeter positive (+) lead against the defogger
wire on the battery side.
(e) Place the voltmeter negative (±) lead with the foil strip
against the wire on the ground side.
(f) Slide the positive (+) lead from the battery to the ground
side.
(g) The point where the voltmeter deflects from several V to
zero V is the place where the defogger wire is broken.
HINT:
If the heat wire is not broken, the voltmeter indicates 0 V at the
positive (+) end of the heat wire but gradually increases to about
12 V as the meter probe moves to the other end.

BE0D8±11
I28395
Transponder Key Coil
Transponder Key AmplifierECM
Instrument
Panel J/B

IGN 1 Fuse
Engine Room J/B

ECU±B Fuse

EFI No. 1 Fuse
Combination Meter

Security Indicator Light
DLC3
Transponder Key ECU
(Located behind the combination meter)
BE±142
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
3546 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

BE2D6±02
I10154
I24870
12
6
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE±143
3547 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECTION TRANSPONDER KEY COIL CONTINU-
ITY
Check that there is continuity between terminals 1 and 2.
If continuity is not as specified, replace the coil.
2. INSPECT TRANSPONDER KEY ECU CIRCUIT
Connect the wire harness side connector to the ECU and in-
spect the wire harness side connector from the back side, as
shown in the table below.
ConditionTester connectionSpecified condition
Always6 ± 12Battery positive voltage
If the circuit is as specified, replace the ECU with a new one.
If the circuit is not as specified, inspect the circuit connected to
other parts.

BO45K±01
H04840
150 mm (5.91 in.)Hole Here BO±8
± BODYHOOD SUPPORT
3561 Author: Date:
2005 SEQUOIA (RM1146U)
HOOD SUPPORT
REPLACEMENT
1. REMOVE HOOD SUPPORT
(a) Remove the bolt and hood support from the hood.
HINT:
While supporting the hood by hand, remove the hood support
from the hood.
(b) Remove the bolt and hood support.
2. IF NECESSARY, REPLACE HOOD SUPPORT
NOTICE:
Handling the hood support

Do not disassemble the support as the cylinder is
filled with pressurized gas.

If the hood support is to be replaced, drill a 2.0 ± 3.0
mm (0.079 ± 0.118 in.) hole in the area shown in the il-
lustration to completely release the high pressure
gas before disposing of it.

When drilling, chips may fly out so work carefully.

The gas is colorless, odorless and non ± toxic.

When working, handle the hood support carefully.
Never score or scratch the exposed part of the piston
rod, and allow any paint or oil to get on it.

Do not turn the piston rod and cylinder with the hood
support fully extended.
3. INSTALL HOOD SUPPORT
(a) Install the bolt and hood support to the body.
Torque: 22 N´m (224 kgf´cm, 16 ft´lbf)
(b) Install the bolt and hood support to the hood.
Torque: 22 N´m (224 kgf´cm, 16 ft´lbf)

BO45T±01
H16689
Back Door Side Garnish
Back Door Center Garnishw/o Rear spoiler:
High Mount Stop Light
Outside MouldingBack Door Hingew/ Rear spoiler:
Rear Spoiler
Back Door Hinge
Rear Wiper Arm
Wiper
Motor
Grommet
Rear Wiper
Motor
Service Hole Plug
Outside MouldingStep Liner Back Door Glass Back Door Side
Garnish
Back Door Glass Run
Outer Weatherstrip
Back Door
Glass Guide Rail
Outer Cover
Power Window Regulator
Back Door
Glass Guide RailOutside Handle
Key Cylinder
Rear Light
Lower Stopper Rear Light Opening Hole Cover
Stopper Cushion
Back Door Lock ProtectorControl
Cable
Stopper Cushion
: Specified torque Strap Cover
Back Door Pull StrapBack Door Trim Board Inner WeatherstripNo. 1 Service
Hole Cover
Opening Hole Cover
19.5 (199, 14.4)
8.0 (82, 71 in.´lbf)
5.5 (56, 49 in.´lbf)
5.5 (56, 49 in.´lbf)
8.0 (82, 71 in.´lbf)
N´m (kgf´cm, ft´lbf)No. 2 Service
Hole Cover
Back Door
Handle
Protector
Licence Plate
Light
Assembly
Outside
Garnish
Washer Nozzle
Lower Stopper
Power Window
Regulator Motor
Back Door Lock
19.5 (199, 14.4)
8.0 (82, 71 in.´lbf)
± BODYBACK DOOR
BO±25
3578 Author: Date:
2005 SEQUOIA (RM1146U)
BACK DOOR
COMPONENTS