2000 SUZUKI SWIFT Transmission Service Workshop Manual

AUTOMATIC TRANSMISSION (4 A/T) 7B-23
ENGINE BRAKE TEST
1) While driving vehicle in 3rd gear of “D” range, shift select lever down to “2” range and check if engine brake
operates.
2) In the same way as in Step 1), check engine brake for operation when select lever is shifted down to “L”
range.
3) Engine brake should operate in above test.
“P” RANGE TEST
1) Stop vehicle on a slope, shift select lever to “P” range and at the same time apply parking brake.
2) After stopping engine, depress brake pedal and release parking brake.
3) Then, release brake pedal gradually and check that vehicle remains stationary.
4) Depress brake pedal and shift select lever to “N” range.
5) Then, release brake pedal gradually and check that vehicle moves.WARNING:
Before test, make sure that there is no vehicle behind so as to pre-
vent rear-end collision.
Test result Possible cause
Fails to operate when shifted down to “2”
rangeDefective shift switch
1st & 2nd brake defective
Direct clutch defective
Fails to operate when shifted down to “L”
range
WARNING:
Before test, check to make sure no one is around vehicle or
down on a slope and keep watchful for safety during test.
Test result Possible cause
Vehicle moves at “P” range or
remains stationary at “N” rangeDefective parking lock pawl or
spring

7B-24 AUTOMATIC TRANSMISSION (4 A/T)
ELECTRONIC CONTROL SYSTEM DIAGNO-
SIS
TCM has on-board diagnostic system (a system self-diagnosis
function). Investigate where the trouble is by referring to “DIAG-
NOSTIC FLOW TABLE” and “DTC TABLE” in this section.
PRECAUTIONS IN DIAGNOSING TROUBLES
[PRECAUTIONS IN IDENTIFYING DTC]
For vehicle equipped with immobilizer indicator lamp (2)
(which comes on when turning on ignition switch leaving
engine OFF), malfunction indicator lamp (MIL) (1) comes on
when TCM detects malfunction of automatic transmission
system.
For vehicle equipped without immobilizer indicator lamp (2),
malfunction indicator lamp (MIL) (1) does not come on
although TCM detects malfunction of automatic transmission
system.
Don’t disconnect couplers from TCM, battery cable from bat-
tery, TCM ground wire harness from engine or main fuse
before checking DTC stored in TCM memory.
Such disconnection will clear memorized information in TCM
memory.
Using SUZUKI scan tool (Tech-1) (4), diagnostic trouble
code (DTC) stored in TCM memory can be checked and
cleared as well.
Before its use, be sure to read Operator’s (instruction) Man-
ual supplied with it carefully to have good understanding of
its functions and usage.
Not using scan tool, the DTC stored in TCM memory also
can be checked and cleared.
DTC stored in the TCM memory is outputted by flashing of
“O/D OFF” lamp (3) with diagnosis switch terminal of monitor
connector No.2 (5) grounded.
If no DTC is stored in TCM memory, DTC No.12 is outputted
repeatedly.
If one or more DTCs are stored in TCM memory, they are
outputted starting from smallest code number in increasing
order.
After all DTCs are outputted, all DTCs are outputted repeat-
edly.
Be sure to read “PRECAUTIONS FOR ELECTRICAL CIR-
CUIT SERVICE” in Section 0A before inspection and
observe what is written there.
When replacing TCM with used one, all learned contents
which are stored in TCM memory should be erased after the
replacement referring to “LEARNING CONTROL INITIAL-
IZATION” in this section.

AUTOMATIC TRANSMISSION (4 A/T) 7B-25
[INTERMITTENT TROUBLES] and [NOTES ON SYSTEM CIR-
CUIT INSPECTION]
Refer to Section 0A.
DTC CHECK
[Check DTC with SUZUKI scan tool]
1) Turn ignition switch OFF.
2) After setting cartridge, connect SUZUKI scan tool to data link
connector (DLC) (1) located on underside of instrument
panel at driver’s seat side.
Special tool
(A) : 09931-76011 (SUZUKI scan tool)
(B) : Mass storage cartridge
(C) : 09931-76030 (16/14 pin DLC cable)
3) Turn ignition switch ON.
4) Read DTC according to instructions displayed on SUZUKI
scan tool and print it or write it down. Refer to SUZUKI scan
tool operator’s manual for further details.
5) After completing the check, turn ignition switch OFF and dis-
connect SUZUKI scan tool from data link connector (DLC)
(1).
[Check DTC without SUZUKI scan tool]
1) Turn ignition switch ON and make sure that O/D OFF lamp is
OFF in combination meter (O/D off switch OFF).
2) Turn ignition switch OFF.
3) Pull out clip (3) and remove glove box (2) from instrument
panel (1).

7B-26 AUTOMATIC TRANSMISSION (4 A/T)
4) Using service wire, ground diagnosis switch terminal (2) of
monitor connector No.2 (1).
5) Turn ignition switch ON.
6) Read DTC from flashing pattern of O/D OFF lamp.
7) After completing the DTC check, turn ignition switch OFF
and disconnect service wire from monitor connector No.2
(1).
3. Ground terminal
1
2
3

AUTOMATIC TRANSMISSION (4 A/T) 7B-27
DTC CLEARANCE
[Clear DTC with SUZUKI scan tool]
1) Turn ignition switch OFF.
2) After setting cartridge to scan tool, connect it to data link
connector (DLC) (1) located on underside of instrument
panel at driver’s seat side.
Special tool
(A) : 09931-76011 (SUZUKI scan tool)
(B) : Mass storage cartridge
(C) : 09931-76030 (16/14 pin DLC cable)
3) Turn ignition switch ON.
4) Erase DTC according to instructions displayed on scan tool.
Refer to SUZUKI scan tool operator’s manual for further
details.
5) After completing the clearance, turn ignition switch OFF and
disconnect scan tool from data link connector (DLC) (1).
[Clear DTC without SUZUKI scan tool]
1) Turn ignition switch ON.
2) Using service wire, ground diagnosis switch terminal (2) of
monitor connector No.2 (1) five times within 10 seconds.
3) Perform “DTC check” and confirm that only DTC12 (normal
DTC) is displayed. If not, repeat step 1) and 2) and check
again.
3. Ground terminal
1
2
3

7B-28 AUTOMATIC TRANSMISSION (4 A/T)
DTC TABLE
DTC NO.
“O/D OFF” Lamp
Flashing Pattern of DTC
(Not using scan tool)DETECTING ITEMSMIL
Using
scan toolNot using
scan toolVehicle
equipped
with
immobi-
lizer indi-
cator lampVehicle
equipped
without
immobi-
lizer indi-
cator lamp
–12 Normal––
P0715 14Input/Turbine speed sensor circuit
malfunction1 driving
cycleNot
applicable
P0730 18 Incorrect gear ratio2 driving
cyclesNot
applicable
P075321
Shift solenoid-A (No.1) electrical1 driving
cycleNot
applicable
22
P075823
Shift solenoid-B (No.2) electrical1 driving
cycleNot
applicable
24
P0763 43 Shift solenoid-C (No.3) electrical1 driving
cycleNot
applicable
P0768 45 Shift solenoid-D (No.4) electrical1 driving
cycleNot
applicable
P0773 48 Shift solenoid-E (No.5) electrical1 driving
cycleNot
applicable
P074325
Torque converter clutch (lock-up)
system electrical1 driving
cycleNot
applicable
26

AUTOMATIC TRANSMISSION (4 A/T) 7B-29
P0741 29Torque converter clutch (lock-up)
solenoid performance or stuck off2 driving
cyclesNot
applicable
P0720 31Output shaft speed sensor circuit
malfunction1 driving
cycleNot
applicable
P170032
Throttle position signal input mal-
function1 driving
cycleNot
applicable
33
P0705 34Transmission range sensor circuit
malfunction1 driving
cycleNot
applicable
P0725 35Engine speed input circuit malfunc-
tion2 driving
cyclesNot
applicable
P071036
Transmission temperature sensor
circuit malfunction2 driving
cyclesNot
applicable
38
P1709 51Engine coolant temperature signal
circuit1 driving
cycleNot
applicable
P0702
52Transmission control system elec-
trical1 driving
cycleNot
applicable
P1702 Internal malfunction of TCMDTC NO.
“O/D OFF” Lamp
Flashing Pattern of DTC
(Not using scan tool)DETECTING ITEMSMIL
Using
scan toolNot using
scan toolVehicle
equipped
with
immobi-
lizer indi-
cator lampVehicle
equipped
without
immobi-
lizer indi-
cator lamp

7B-30 AUTOMATIC TRANSMISSION (4 A/T)
TCM POWER AND GROUND CIRCUIT CHECK
1. Battery 4. Circuit fuse (IG) 7. TCM
2. Main fuse 5. Ground
3. Ignition switch 6. A/T relay
DTC DETECTING CONDITION
Automatic transmission doesn’t shift to 1st gear at vehicle start in “D” range.
Step Action Yes No
1 Check voltage between terminal “C44-2” of
TCM coupler and body ground with ignition
switch ON.
Is it 10 – 14 V?Go to Step 2. YEL/BLK wire open or
faulty
A/T relay.
2 Check voltage between terminal “C44-15” of
TCM coupler and body ground with ignition
switch ON.
Is it about 0 V?Poor “C44-2” or “C44-15”
connection.
If all above are OK,
replace known-good TCM
and recheck.“BLK” wire open.