2000 SUZUKI SWIFT Transmission Service Workshop Manual

AUTOMATIC TRANSMISSION (4 A/T) 7B-79
4) Remove output shaft speed sensor (1) and input shaft speed
sensor (2).
5) Remove transmission range sensor (3).
6) Remove dropping resistor (4).
7) Remove breather hose (5).
8) Remove A/T fluid level gauge (1) and filler tube (2).
9) Remove vehicle speed sensor (1) (for speedometer), shift
cable bracket (2) and connector clamp bracket (3).
10) Remove oil pan and oil pan gasket.
11) Remove oil strainer assembly (1), and detach transmission
temperature sensor (2).
NOTE:
 For removal of oil pan, do not turn transmission over
as this will contaminate valve body with foreign materi-
als in the bottom of oil pan.
 When removing oil pan, tap around it lightly with a
plastic hammer. Do not force it off by using a screw-
driver or the like.

7B-80 AUTOMATIC TRANSMISSION (4 A/T)
12) Disconnect couplers from solenoid valves, and transmission
temperature sensor.
Remove transmission temperature sensor.
13) Remove valve body assembly (1).
14) Remove solenoid harness assembly.
15) Remove accumulator pistons and springs.
To remove C0 (1), C2 (2) and B1 (3) accumulator pistons
and springs, position a rag on pistons to catch each piston.
To remove pistons, force low-pressure compressed air (1 kg/
cm
2, 15 psi, 100 kPa, max) into hole (4) as shown in figure,
and pop each piston into the rag.
To remove B0 and C1 accumulator pistons and springs,
remove each snap ring and accumulator spacer, then
remove spring and piston.
16) Remove torque converter housing (1).
a) Remove housing bolts.
b) Remove housing while tapping around it lightly with a plas-
tic hammer. CAUTION:
Be careful not to let manual valve fall off when removing
valve body assembly.
NOTE:
There are three kinds of bolts (bolts A, B and C) fixing
valve body assembly.
2. Bolt A
3. Bolt B
4. Bolt C
NOTE:
Do not push accumulator pistons with fingers or any-
thing before removing them. Pushing them may cause
compressed fluid in accumulator to spew out of hole and
get to your face and clothes.
NOTE:
Never reuse bolts A shown in figure.

AUTOMATIC TRANSMISSION (4 A/T) 7B-81
17) Remove thrust needle roller bearing (1) and thrust bearing
race (2) from the top of counter driven gear assembly (3).
18) Remove differential gear assembly (1).
19) Remove oil pump assembly and gasket (1).
20) Remove front clutch assembly (1).
21) Remove thrust bearing race (1) and thrust needle roller bear-
ing (2).

7B-82 AUTOMATIC TRANSMISSION (4 A/T)
22) Remove rear clutch assembly (1).
23) Remove intermediate shaft assembly (1) and follow shaft
assembly (2).
24) Remove reverse brake (B2) snap ring, brake flange, brake
discs, brake plates and cushion plate.
25) Remove oil guide plate (1) parking lock pawl cover (2), shaft,
torsional spring (3) and parking lock pawl (4).
26) Remove parking lock pawl sleeve (5).

AUTOMATIC TRANSMISSION (4 A/T) 7B-83
27) Remove counter driven gear assembly (1) and thrust needle
roller bearing (2).
28) Remove control shift lever (1), nuts (2), washer (3) from
manual shift shaft (4).
29) Remove detent spring (1).
30) Remove manual shift shaft (1) with parking lock rod (2), and
washer (3) from transmission case.

7B-84 AUTOMATIC TRANSMISSION (4 A/T)
31) Remove rear cover assembly (1), thrust washer (2) and
thrust needle roller bearing (3).
Remove gasket (4).
32) Remove direct clutch (C0) assembly (1), thrust roller bearing
(2) and rear planetary sun gear No.1 assembly (3).
33) Remove planetary set (1) with bearing, thrust needle roller
bearing (2).
34) Remove O/D brake (B0) piston adapter (1), B0 plates (2)
and discs (3).

AUTOMATIC TRANSMISSION (4 A/T) 7B-85
35) Remove planetary sun gear No.2 (1) and thrust needle roller
bearing (2).
36) Remove snap ring, then remove brake flange and disc.
37) Remove snap ring, then remove brake discs and plates (B1
brake).
38) Remove snap ring (1), then O/D brake return spring seat (2),
return spring (3) and spring retainer (4).
39) Remove snap ring (1) then remove 1st & 2nd brake piston
return spring subassembly (2) and 1st & 2nd brake piston
(3).
To remove 1st & 2nd brake piston, force low-pressure com-
pressed air (1 kg/cm
2, 15 psi, 100 kPa, max) into hole (5)
shown in figure and pop out 1st & 2nd brake piston into a
rag.
4. Air gun

7B-86 AUTOMATIC TRANSMISSION (4 A/T)
40) Remove counter drive gear (1).
41) Use hydraulic press (8) and special tool to compress wave
spring (4), then remove snap ring (1).
Special tool
(A) : 09926-96040
42) Remove reverse brake piston seat (3), wave spring (4) and
reverse brake piston (5).
To remove reverse brake piston, force low-pressure com-
press air (1 kg/cm
2, 15 psi, 100 kPa, max) into hole (7)
shown in figure, and pop out piston into a rag.
NOTE:
 Do not compress wave spring more than necessary.
 Do not reuse snap ring (1).
2. Flat end rod or the like
6. Air gun