1999 TOYOTA CAMRY torque

BO2E0±01
H09269
Anchor Cover Cap
Front Seat Outer Belt
Rear Seat Outer Belt
41 (420, 30)
LH Rear Seat Inner
with Center Belt Front Seat
RH Rear Seat Inner
with Center Belt
41 (420, 31)
41 (420, 30)
41 (420, 31)
41 (420, 30)
41 (420, 30)
41 (420, 30)
N´m (kgf´cm, ft´lbf): Specified torque
41 (420, 30)
7.8 (80, 69 in.´lbf)
BO±26
± BODYSEAT BELT
565 Author: Date:
SEAT BELT
COMPONENTS

F05595
F05596
BR0AB±03
F05597
R00252
BR±4
± BRAKEBRAKE FLUID
2027 Author: Date:
BRAKE FLUID
BLEEDING
HINT:
If any work is done on the brake system or if air is suspected in
the brake lines, bleed the air from the system.
NOTICE:
Do not let brake fluid remain on a painted surface. Wash it
off immediately.
1. FILL BRAKE RESERVOIR WITH BRAKE FLUID
Check the fluid level in the reservoir after bleeding each wheel.
Add fluid, if necessary.
Fluid: SAEJ1703 or FMVSS No.116 DOT 3
2. BLEED MASTER CYLINDER
HINT:
If the master cylinder has been disassembled or if the reservoir
becomes empty, bleed the air from the master cylinder.
(a) Disconnect the 2 brake lines from the master cylinder.
(b) Slowly depress the brake pedal and hold it.
(c) Block off the outlet plugs with your fingers, and release
the brake pedal.
(d) Repeat (b) and (c) 3 or 4 times.
3. CONNECT VINYL TUBE TO BRAKE CALIPER OR
WHEEL CYLINDER BLEEDER PLUG
Insert the other end of the tube in a half±full container of brake
fluid.
NOTICE:
Bleed air of the rear brake first. If front brake is bled first,
rear brake air cannot be bled.
4. BLEED BRAKE LINE
(a) Slowly depress the brake pedal several times.
(b) While an assistant depresses the pedal, loosen the
bleeder plug until fluid starts to run out. Then tighten the
bleeder plug.
(c) Repeat this procedure until there are no more air bubbles
in the fluid.
Torque: (Bleeder plug)
8.3 N´m (85 kgf´cm, 74 in.´lbf)
5. REPEAT PROCEDURE FOR EACH WHEEL

R00954
Stop Light
Switch
Push Rod
Pedal HeightBR0YH±01
R00935
Pedal Freeplay
± BRAKEBRAKE PEDAL
BR±5
2028 Author: Date:
BRAKE PEDAL
ON±VEHICLE INSPECTION
1. CHECK PEDAL HEIGHT
Pedal height from asphalt sheet:
152.0 ± 162.0 mm (5.984 ± 6.378 in.)
2. IF NECESSARY, ADJUST PEDAL HEIGHT
(a) Disconnect the connector from the stop light switch.
(b) Loosen the stop light switch lock nut and remove the stop
light switch.
(c) Loosen the push rod lock nut.
(d) Adjust the pedal height by turning the pedal push rod.
(e) Tighten the push rod lock nut.
Torque: 25 N´m (260 kgf´cm, 19 ft´lbf)
(f) Install the stop light switch and turn it until it lightly con-
tacts the pedal stopper.
(g) Push in the brake pedal 5±15 mm (0.20±0.59 in.), turn the
stop light switch to lock the nut in the position where the
stop light goes off.
(h) Connect the connector to the stop light switch.
(i) After installation, push in the brake pedal 5±15 mm
(0.20±0.59 in.), check that stop light lights up.
(j) Connect the connector to the stop light switch.
(k) After adjusting the pedal height, check the pedal freeplay.
3. CHECK PEDAL FREEPLAY
(a) Stop the engine and depress the brake pedal several
times until there is no more vacuum left in the booster.
(b) Push in the pedal by hand until the resistance begins to
be felt, then measure the distance.
Pedal freeplay: 1 ± 6 mm (0.04 ± 0.24 in.)
HINT:
The freeplay to the 1st resistance is due to the play between the
clevis and pin. This is magnified up to 1 ± 6 mm (0.04 ± 0.24 in.)
at the pedal.
If incorrect, check the stop light switch clearance.
If the clearance is OK, then troubleshoot the brake system.
Stop light switch clearance:
0.5 ± 2.4 mm (0.020 ± 0.094 in.)

BR0YI±01
F07004
Lower Panel Insert

Bushing ClipClevis PinNo.1 Lower Panel
Return Spring
Cushion Plate
Collar
Brake Pedal
Cowl Side Trim Front Opening Cover
Brake Pedal
Inside Scuff PlateM/T: Stop Light Switch
Wave Washer
Cruise Control ECU
Lithium soap base glycol grease
13 (130, 9)
5.0 (51, 44 in.´lbf)
13 (130, 9)
Pedal Pad
Pedal Pad
Bushing A/T:
39 (400, 29)
: Specified torqueN´m (kgf´cm, ft´lbf)

Non±reusable partBrake Pedal Bracket
± BRAKEBRAKE PEDAL
BR±7
2030 Author: Date:
COMPONENTS

W03254
W03255
Lock Nut
Adjusting Nut
BR0AD±03
BR±8
± BRAKEPARKING BRAKE LEVER
2031 Author: Date:
PARKING BRAKE LEVER
ON±VEHICLE INSPECTION
1. CHECK THAT PARKING BRAKE LEVER TRAVEL
Pull the parking brake lever all the way up, and count the num-
ber of clicks.
Parking brake lever travel at 196 N (20 kgf, 44.1 lbf):
5 ± 8 clicks
If incorrect, adjust the parking brake.
2. IF NECESSARY, ADJUST PARKING BRAKE LEVER
TRAVEL
HINT:
Before adjusting the parking brake lever travel, make sure that
the rear brake shoe clearance has been adjusted. For shoe
clearance adjustment, see step 2 on page BR±35 or step 1 on
page BR±48.
(a) Remove the console box.
(b) Loosen the lock nut and adjust the adjusting nut until the
lever travel is correct.
(c) Tighten the lock nut.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(d) Install the console box.

BR0AE±02
Z19120
w/ ABS (& TRAC)
2±way
15 (155, 11)
13 (130, 9)
Master Cylinder

GasketBrake Booster
N´m (kgf´cm, ft´lbf) : Specified torque

Non±reusable part w/o ABS
3±way
W03569
N´m (kgf´cm, ft´lbf) : Specified torque
Lithium soap base glycol grease
Grommet
Cylinder BodyNo. 2 PistonNo. 1 Piston SpringSpring Cap
Strainer
Reservoir
Grommet Straight PinReservoir Set Screw
1.7 (18, 16 in.´lbf)
w/ TRAC
± BRAKEBRAKE MASTER CYLINDER
BR±9
2032 Author: Date:
BRAKE MASTER CYLINDER
COMPONENTS

Z19122
w/o ABS
w/ ABSCap
Strainer
Reservoir
No. 2 Piston and Spring
No. 1 Piston and Spring
Cylinder Body
Stopper Bolt
Gasket Reservoir Set Screw
GrommetSnap Ring
Grommet
Cap
Strainer
Reservoir
Reservoir Set Screw
Cylinder Body

Gasket
Stopper Bolt GrommetGrommet
No. 1 Piston and SpringNo. 2 Piston and SpringSnap Ring
Lithium soap base glycol grease
Non±reusable part
N´m (kgf´cm, ft´lbf): Specified torque
1.7 (18, 16 in.´lbf)
10 (100, 7)
1.7 (18, 16 in.´lbf)
10 (100, 7)
BR±10
± BRAKEBRAKE MASTER CYLINDER
2033 Author: Date:

BR0AF±03
W04697
SST
R11405
± BRAKEBRAKE MASTER CYLINDER
BR±11
2034 Author: Date:
REMOVAL
1. DISCONNECT LEVEL WARNING SWITCH CONNEC-
TOR
2. TAKE OUT FLUID WITH SYRINGE
NOTICE:
Do not let brake fluid remain on a painted surface. Wash it
off immediately.
3. DISCONNECT BRAKE LINES
(a) w/ ABS (& TRAC):
Using SST, disconnect the 4 brake lines.
SST 09023±00100
Torque: 15 N´m (155 kgf´cm, 11 ft´lbf)
(b) w/o ABS:
Using SST, disconnect the 5 brake lines.
SST 09023±00100
Torque: 15 N´m (155 kgf´cm, 11 ft´lbf)
4. REMOVE MASTER CYLINDER
Remove the 2 nuts, and pull out the 2 or 3±way, master cylinder
and gasket.
Torque: 13 N´m (130 kgf´cm, 9 ft´lbf)