1999 TOYOTA CAMRY torque

H092532 Clips
H09254
3 Clips
Clip
H09255
2
1 1
H07599
2
1
± BODYLUGGAGE COMPARTMENT DOOR AND HINGE
BO±7
8. REMOVE REAR FLOOR FINISH PLATE
(a) Using a clip remover, remove the 2 clips.
HINT:
Tape the screwdriver tip before use.
(b) Insert a screwdriver between the rear floor finish plate and
body to pry out the rear floor finish plate.
HINT:
Tape the screwdriver tip before use.
9. REMOVE REAR SEAT CUSHION AND SEATBACK
(See page BO±22)
10. REMOVE ROOF SIDE INNER GARNISH
(a) Using a clip remover, remove the clip.
(b) Insert a screwdriver between the roof side inner garnish
and body to pry it out.
HINT:
Tape the screwdriver tip before use.
(c) Employ the same manner described above to the other
side.
11. REMOVE HIGH±MOUNTED STOP LIGHT
Remove the high±mounted stop light as shown in the illustra-
tion, then disconnect the connector.
12. REMOVE PACKAGE TRAY TRIM
(a) Remove the bolts and rear seat outer belt floor anchors.
Torque: 41 N´m (420 kgf´cm, 31 ft´lbf)
(b) Using a screwdriver, remove the seat belt bezels from the
package tray trim.
HINT:
Tape the screwdriver tip before use.
(c) Using a hexagon wrench, remove the 2 hexagon screws.
(d) Remove the package tray trim, then disconnect the con-
nectors.
HINT:
Remove the package tray trim through out the rear seat outer
belt floor anchors from the hole in the package tray trim.
13. REMOVE NO. 1 UPPER BACK PANEL HOLE COVER
Remove the 2 clips and No. 1 upper back panel hole cover.
14. REMOVE LUGGAGE COMPARTMENT DOOR SUP-
PORTS
Remove the 4 bolts and luggage compartment door support.
Torque: 22 N´m (224 kgf´cm, 16 ft´lbf)
15. REMOVE LUGGAGE COMPARTMENT DOOR HINGES
Remove the pins and luggage compartment door hinges.

BO2DQ±01
BO±8
± BODYLUGGAGE COMPARTMENT DOOR AND HINGE
DISASSEMBLY
1. REMOVE DOOR LOCK
(a) Disconnect the control link.
(b) Remove the 2 bolts and door lock.
Torque: 5.4 N´m (55 kgf´cm, 49 in.´lbf)
2. REMOVE REAR COMBINATION LIGHTS
(a) Disconnect the connectors.
(b) Remove the 6 nuts and rear combination lights.
3. REMOVE DOOR LOCK CYLINDER
Remove the 2 bolts and door lock cylinder.
Torque: 5.4 N´m (55 kgf´cm, 49 in.´lbf)

BO2DR±01
H09256
N21779
± BODYLUGGAGE COMPARTMENT DOOR AND HINGE
BO±9
ADJUSTMENT
1. ADJUST LUGGAGE COMPARTMENT DOOR
(a) Remove the 11 clips and luggage compartment door cov-
er.
(b) Loosen the bolts to adjust the lggage compartment door
in forward/rearward and left/right directions.
(c) Tighten the loosened bolts again.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
(d) Increase or decrease the number of washers between the
hinge and door panel to adjust vertical direction.
2. ADJUST DOOR LOCK STRIKER
(a) Remove the rear floor finish side plates.
(b) Remove the rear floor finish plate.
(c) Loosen the 2 lock striker set bolts.
(d) Using a hammer and brass bar, tap the striker to adjust it.
(e) Tighten the loosened bolts again.
Torque: 5.4 N´m (55 kgf´cm, 49 in.´lbf)

H09251
BO2DU±01
H11085
Hole Here
150 mm (5.91 in.) BO±12
± BODYLUGGAGE COMPARTMENT DOOR SUPPORT
551 Author: Date:
LUGGAGE COMPARTMENT DOOR
SUPPORT
REPLACEMENT
1. REMOVE LUGGAGE COMPARTMENT TRIM FRONT
COVER
Using a clip remover, remove the 6 clips and luggage compart-
ment trim front cover.
HINT:
Tape the screwdriver tip before use.
2. REMOVE LUGGAGE COMPARTMENT DOOR SUP-
PORT
(a) Remove the 2 bolts and luggage compartment door sup-
port from the luggage compartment door panel.
HINT:
While supporting the door with your hand, remove the support.
(b) Remove the 2 bolts and support from the body.
3. IF NECESSARY, REPLACE LUGGAGE COMPART-
MENT DOOR SUPPORT
NOTICE:
When handling the luggage compartment door support.

Do not disassemble the luggage compartment door
support because the cylinder is filled with pressur-
ized gas.

If the luggage compartment door support is to be re-
placed, drill a 2.0 ± 3.0 mm (0.079 ± 0.118 in.) hole in
the bottom of the luggage compartment door support
as shown in the illustration to completely release the
high±pressure gas before disposing of it.

When drilling, chips may fly out so work carefully.

The gas is colorless, odorless and non±toxic.

When working, handle the luggage compartment
door support carefully. Never score or scratch the ex-
posed part of the piston rod, and never allow paint or
oil to get on it.

Do not turn the piston rod and cylinder with the lug-
gage compartment door support fully extended.
4. INSTALL LUGGAGE COMPARTMENT DOOR SUP-
PORT
(a) Install the bolt and luggage compartment door support to
the body.
Torque: 22 N´m (224 kgf´cm, 16 ft´lbf)

± BODYLUGGAGE COMPARTMENT DOOR SUPPORT
BO±13
552 Author: Date:
(b) Install the 2 bolts and luggage compartment door support
to the luggage compartment door panel.
Torque: 22 N´m (224 kgf´cm, 16 ft´lbf)
5. INSTALL LUGGAGE COMPARTMENT TRIM FRONT
COVER

BO2E2±01
H09257
N´m (kgf´cm, ft´lbf) : Specified Torque
Stopper
Back Window Outside Moulding
High±mounted Stop Light Rear SeatbackBack Window Glass
Roof Side Inner Garnish
Package Tray Trim
Rear Seat Cushion
Roof Side Inner Garnish

Non±reusable part
18 (185, 13)
LH Rear Seat
Outer Belt
41 (420, 30)
RH Rear Seat Outer Belt
BO±14
± BODYBACK WINDOW GLASS
553 Author: Date:
BACK WINDOW GLASS
COMPONENTS

BO2DV±02
H09268
Headrest SupportHeadrest
Headrest
Rear Seatback Pad
Rear Seatback Cover
Rear Seat Cushion Cover

Hog Ring
HookRear Seat Cushion Cover Headrest Support
Hook
Rear Seat Cushion Cover
18 (185, 13)
N´m (kgf´cm, ft´lbf): Specified torque
Hog Ring
18 (185, 13)
± BODYREAR SEAT
BO±21
560 Author: Date:
REAR SEAT
COMPONENTS

BO2DW±01
BO±22
± BODYREAR SEAT
REMOVAL
1. REMOVE REAR SEAT CUSHION ASSEMBLY
Pull up the front part of seat cushion assembly to remove the rear seat cushion assembly.
HINT:
When removing the rear seat cushion assembly, pass the rear seat inner with center belt through the hole
on the seatback.
2. REMOVE REAR SEATBACK ASSEMBLY
(a) Remove the 3 bolts.
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)
HINT:
At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent
wrinkles as little as possible.
(b) Pull up the seatback assembly to remove it.