1999 TOYOTA CAMRY torque

BO0N5±01
H01875
Rear seatback Board
Rear Seatback frame
RH Rear Side
SeatbackRear Seatback CoverRear Seatback PadHeadrest
Support
LH Seatback Hinge Seatback Lock Knob
Seatback Lock Knob
Cover
Rear Seatback Lock
Control Cable
Rear Seatback
Control Bezel
Seat Cushion Cover LH Side Seatback Headrest
Headrest Suppot
Seatback Pad
Seatback Cover
Seat Cushion Pad
Child Restraint Seat Headrest
Rear Seatback Lock
Control
Center Seatback
Hinge
Center Seatback
Hinge
: Specified torque
N´m (kgf´cm, ft´lbf)
RH Seatback Hinge
Rear Seat center
Armrest
18 (185, 13)18 (185, 13)
18 (185, 13)Center Armrest
Hinge Cover18 (185, 13)
18 (185, 13)
7.8 (79, 69 in.´lbf)
42 (428, 31)
13 (130, 9)
17.5 (178, 12.5)
Child Restraint
Seat Coverw/ CRS: BO±118
± BODYREAR SEAT (TMMK Made)
2466 Author: Date:
REAR SEAT (TMMK Made)
COMPONENTS

BO0N6±01
± BODYREAR SEAT (TMMK Made)
BO±119
2467 Author: Date:
REMOVAL
1. REMOVE SEAT CUSHION ASSEMBLY
(a) Remove the seat cushion assembly.
HINT:
Remove the rear seat inner with center belt from seat cushion slit to remove the seat cushion.
(b) Remove the 2 lock hooks.
2. REMOVE LH SEATBACK ASSEMBLY
(a) Release lock to lean the seatback to front.
(b) Remove the 2 bolts and LH seatback assembly.
3. w/ CRS:
REMOVE CHILD RESTRAINT SEAT
(a) Remove child restraint seat cover.
(b) Remove the 3 bolts and 2 nuts.
Torque: 13 N´m (130 kgf´cm, 9 ft´lbf)
(c) Remove the child restraint seat.
4. w/o CRS:
REMOVE RH SEATBACK ASSEMBLY
(a) Release lock to lean the seatback to front.
(b) Remove the clips.
(c) Remove the bolts and RH seatback assembly.
5. w/ CRS:
REMOVE RH SEATBACK ASSEMBLY
(a) Remove the 3 bolts.
Torque:
RH bolt: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
Center bolt: 42 N´m (428 kgf´cm, 31 ft´lbf)
(b) Remove the RH seatback assembly.
6. REMOVE LH AND RH REAR SIDE SEATBACK
(a) Remove the bolt and LH rear side seatback.
(b) Remove the bolt and RH rear side seatback.
7. REMOVE SEATBACK HINGE
(a) Remove the bolt and LH seatback hinge.
(b) Remove the 2 bolts and center seatback hinge.
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)
(c) w/o CRS:
Remove the bolt and RH seatback hinge.
Torque: 18 N´m (185 kgf´cm, 13 ft´lbf)

BO0N7±01
BO±120
± BODYREAR SEAT (TMMK Made)
2468 Author: Date:
DISASSEMBLY
1. REMOVE SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat cushion pad.
2. REMOVE THESE PARTS:
HINT:
Remove the clips to turn over the seatback cover before performing the following steps.
(a) Headrest
(b) Rear seatback control Bezel
(c) Headrest supports
(d) Seatback lock knob
(e) Seatback lock knob cover
(f) Rear seat center armrest
3. REMOVE SEATBACK COVER
(a) Remove the hog rings and seatback frame from the seatback cover with pad.
(b) Remove the hog rings and seatback cover from the satback pad.
4. REMOVE SEATBACK LOCK
(a) Remove the rear seatback lock control cable.
(b) Remove the 2 bolts and rear seatback lock control.
Torque: 17.5 N´m (178 kgf´cm, 12.5 ft´lbf)

BO0NF±01
H01877
42 (420, 31)
Front Seat
Outer Belt
42 (420, 31)
Rear Seat
Center Belt
42 (420, 31)
Front Seat
42 (420, 31)
Front Seat Inner
Belt
42 (420, 31)
Rear Seat Inner Belt
N´m (kgf´cm, ft´lbf): Specified torque
Rear Seat
Outer Belt
7.8 (79, 69 in.´lbf)
42 (420, 31)
± BODYSEAT BELT
BO±123
2471 Author: Date:
SEAT BELT
COMPONENTS

BO0NL±01
H01352
BO±134
± BODYSEAT BELT PRETENSIONER
2482 Author: Date:
INSTALLATION
NOTICE:
Never use seat belt pretensioner from another vehicle.
When replace parts, replace them with new parts.
1. INSTALL FRONT SEAT OUTER BELT
(a) Install the front seat belt parts by following the reverse or-
der of removal and torque the following bolts.
(1) Front seat outer belt retractor
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
(2) Seat belt shoulder anchor
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
(3) Seat belt floor anchor
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
NOTICE:

Make sure that the front seat outer belt is installed
with the specified torque.

If the front seat outer belt has been dropped, or there
are cracks, dents or other defects in the case or con-
nector, replace the front seat outer belt with a new
one.

When installing the front seat outer belt, take care that
the wiring does not interfere with other parts and is
not pinched between other parts.
(b) Connect the pretensioner connector as shown in the il-
lustration.
(c) w/ Seat Belt Warning:
Connect the retractor switch connector.
2. INSTALL THESE PARTS:
(a) Center pillar lower garnish
(b) Front door scuff plate

BO2DN±01
H09249
Luggage Compartment
Trim Front Cover
Rear Bumper Reinforcement
Rear Bumper Energy Absorber
Rear Bumper
Side Retainer
Quarter Air Duct
Rear Bumper Cover Rear Bumper
Side RetainerInner Luggage Compartment
Trim Cover
34 (350, 25)
4.9 (50, 43 in.´lbf)
4.9 (50, 43 in.´lbf)
N´m (kgf´cm, ft´lbf) : Specified TorqueInner Luggage Compartment
Trim Cover
Spare Wheel Cover
4.9 (50, 43 in.´lbf)
4.9 (50, 43 in.´lbf)
4.9 (50, 43 in.´lbf)
BO±4
± BODYREAR BUMPER
543 Author: Date:
REAR BUMPER
COMPONENTS

BO2DO±02
H09250
Luggage Compartment
Door HingeLuggage Compartment DoorLuggage Compartment
Door Hinge
Door Lock Cylinder
Door Lock StrikerDoor Lock
Door Support
Inner Luggage Compartment
Trim Cover
Spare Wheel
Rear SeatbackSpare Wheel Cover
Spare Wheel
Carrier
Spare Wheel
Carrier Spacer
Luggage Compartment
Trim Front Cover
Rear Floor Finish
Side Plate
Rear Seat Outer BeltInner Lower Luggage
Compartment Trim Cover
Rear Seat Outer Belt Rear Floor Finish
Side Plate
Rear Seat CushionRoof Side
Inner Garnish
No. 1 Upper Back Panel Hole CoverPackage Tray Trim High±mounted
Stop Light
Roof Side
Inner Garnish
41 (420, 31)
41 (420, 31)
7.8 (80, 69 in.´lbf)
5.4 (55, 49 in.´lbf)
Luggage Compartment Door Cover
x11
N´m (kgf´cm, ft´lbf) : Specified TorqueReat Combination Light
22 (224, 16)
22 (224, 16)
5.4 (55, 49 in.´lbf)
18 (185, 13)
7.8 (80, 69 in.´lbf)
22 (224, 16)
Rear Floor
Finish Plate
± BODYLUGGAGE COMPARTMENT DOOR AND HINGE
BO±5
544 Author: Date:
LUGGAGE COMPARTMENT DOOR AND HINGE
COMPONENTS

BO2DP±01
H09251
H09252
BO±6
± BODYLUGGAGE COMPARTMENT DOOR AND HINGE
REMOVAL
1. REMOVE LUGGAGE COMPARTMENT DOOR COVER
Remove the 11 clips and luggage compartment door cover.
2. REMOVE LUGGAGE COMPARTMENT DOOR
(a) Disconnect the connectors.
(b) Using a clip remover, disconnect the clamps.
(c) Remove the 4 bolts and door.
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
3. REMOVE LUGGAGE COMPARTMENT TRIM FRONT
COVER
Using a clip remover, remove the 6 clips and luggage compart-
ment trim front cover.
4. REMOVE SPARE WHEEL COVER
5. REMOVE INNER LUGGAGE COMPARTMENT TRIM
COVER
(a) Using a clip remover, remove the 2 clips and inner lug-
gage compartment trim cover.
(b) Employ the same manner described above to the other
side.
6. REMOVE REAR FLOOR FINISH SIDE PLATES
Using a clip remover, remove the 6 clips and 2 rear floor finish
side plates.
7. REMOVE INNER LOWER LUGGAGE COMPARTMENT
TRIM COVER
(a) Remove the spare wheel carrier, spare wheel carrier
spacer and spare wheel.
(b) Using a clip remover, remove the 3 clips and inner lower
luggage compartment trim cover.
HINT:
Tape the screwdriver tip before use.