1999 TOYOTA CAMRY torque

REAR BEARING O±RING SERVICE TIP ± SU001-02March 1, 2002
Page 2 of 2
4. Remove Rear Axle Hub.
A. Remove the 4 bolts and rear
axle hub.
Torque: 80 Nm (820 kgfcm, 59 ftlbf)
B. Remove the O±ring.
HINT:
At the time of installation, coat the new
O±ring with MP grease.
NOTE:
Please ensure that the O±ring is
replaced with a new service part when
installing the bearing assembly.
C. With Drum Brake:
Remove the bolt, and disconnect
the flexible hose from the shock
absorber.
Torque: 29 Nm (300 kgfcm, 22 ftlbf)
D. Support the backing plate
securely.
5. With ABS:
Remove ABS Speed Sensor.
Torque: 8.0 Nm (82 kgfcm, 71 inlbf)
INSTALLATION
Installation is in the reverse order of
removal.
Bolt
BoltBolt
Bolt

Page 3 of 6
TRANSMISSION OIL COOLER INSTALLATION ± TC003±97 October 17, 1997
Procedure2. Cooler Installation:
(Continued)
A. Install the 140 mm (5.51º) hose to
the oil cooler tube No. 1 as shown.
NOTE:
Install the hose clamp with the hose
clamp clip at the position shown, and
use pliers to pull off the clip in the
direction indicated by the arrow.
B. Install the tube bracket onto the left
side of the front suspension
member with the 2 bolts as shown.
Torque: 62 in±lbf
(7 N±m / 71 kgf±cm)
C. Install the 130 mm (5.12º) hoses
and the 180 mm (7.09º) hose to the
oil cooler tube No. 2 as shown.
NOTE:
Install the hose clamps with the hose
clamp clips at the positions shown,
and use pliers to pull off the clips in
the direction indicated by the arrows.
Fig. 5
Oil Cooler Tube No. 1
140 mm Hose
5 mm (0.20º)
Fig. 6
Fig. 7
5 mm (0.20º)
180 mm Hose Oil Cooler Tube No. 2
130 mm Hose

TRANSMISSION OIL COOLER INSTALLATION ± TC003±97 October 17, 1997
ProcedureD. Remove the lower side clip of the
(Continued) radiator side LH deflector.
E. Install the tube bracket with the bolt
on the side member.
Torque: 62 in±lbf
(7 N±m / 71 kgf±cm)
F. Reinstall the lower side clip
of the radiator LH deflector.
G. Connect the hoses from the oil
cooler tube No. 2 to the oil cooler
tube No.1.
NOTE:
Install the hose clamps with the hose
clamp clips at the positions shown, and
use pliers to pull off the clips in the
direction indicated by the arrows.
H. Disconnect the hose from the oil
cooler pipe of the radiator LH side.
NOTE:
Place a container below vehicle to catch
any leaking ATF. Remove the other end
of this hose from transaxle and discard.
I. Connect the hose from oil cooler
tube No.1 to the oil cooler pipe of
the radiator LH side.
NOTE:
Install the hose clamps with the hose
clamp clips at the positions shown, and
use pliers to pull off the clips in the
direction indicated by the arrows.
Page 4 of 6
Fig. 8
Oil Cooler Tube No. 1
Front Suspension Member
5 mm (0.20º)
Fig. 9
Fig. 10
5 mm (0.20º)

Page 5 of 6
TRANSMISSION OIL COOLER INSTALLATION ± TC003±97 October 17, 1997
ProcedureJ. Install the 190 mm (7.48º) hose
(Continued) between the oil cooler tube No.1
and transaxle oil cooler tube.
NOTE:
Install the hose clamps with the hose
clamp clips at the positions shown, and
use pliers to pull off the clips in the
direction indicated by the arrows.
K. Install the oil cooler onto the center
brace and front cross member
using the two bolts and nut as
illustrated in figure 12.
Torque: 65.5 in±lbf
(7.4 N±m/75.5 kgf±cm)
L. Connect the hoses to the pipes.
NOTE:
Install the hose clamps with the hose
clamp clips at the positions shown, and
use pliers to pull off the clips in the
direction indicated by the arrows.
Fig. 11
5 mm (0.20º)
190 mm Hose
5 mm (0.20º) Oil Cooler Tube No. 1
Fig. 13

A/C COMPRESSOR INSTALLATION PROCEDURE ± AC003-04March 1, 2004
Page 2 of 2
1. AZ Series Engine:
Install A/C Compressor
A. Loosely install the compressor
(with the 3 bolts and nut or
4 bolts.)
Push down on the rear side of the
compressor and tighten the
bolts/nut in the order shown.
Torque: 24.5 Nm (250 kgfcm, 18 ftlbf)
2. ZZ Series Engine:
Install A/C Compressor
A. Loosely install the compressor
(with the 2 bolts and nut or
3 bolts).
Push down on the rear side of
the compressor and tighten the
bolts/nut in the order shown.
Torque: 29 Nm (295 kgfcm, 21 ftlbf) Installation
Procedure
(Continued)
BoltBoltPush
Nut or Bolt
Bolt12
34
BoltPush
Nut or Bolt Bolt
12
3