1999 TOYOTA CAMRY torque

DOOR MIRROR INSTALLATION ± BO015-00 March 24, 2000
Page 2 of 2
4. For vehicles without a speaker,
tighten the three mirror mounting nuts.
Torque: 5.5 Nm (56 kgfcm, 49 inlbf)
Connect the mirror wire.
5. For vehicles with a speaker, tighten
the two mirror mounting nuts.
Torque: 5.5 Nm (56 kgfcm, 49 inlbf)
Connect the mirror wire.
While lightly pulling the mirror wire
backward, reinstall the door speaker (one
nut at the lower bracket) onto the door as
shown in the illustration.
Torque: 5.5 Nm (56 kgfcm, 49 inlbf)
NOTE:
Do NOT mount the upper speaker
bracket behind the nut.
6. Check the following items:
There is no clearance between
the door mirror base and the door
molding lip.
The mirror wire is free from the
speaker bracket.
The door frame molding lip is not
tucked under the mirror base.
The speaker wire does not
contact the mirror mounting
screw.
Make sure the power mirror
adjustment and the door speaker
functions properly.
7. Install the front door lower frame
bracket garnish/speaker cover.
8. Install the black cap onto the nut.
Installation
Procedure
(Continued)Mounting
Nuts
Mounting
Nuts
Speaker
INCORRECTCORRECT
Mounting Lip
Mirror Base
Speaker Cover
Garnish
Cap

POWER SEAT MOTOR CABLE REPAIR TIP ± BO017-01 Revised May 25, 2001
Page 2 of 2
1. Remove the seat assembly from the
vehicle.
Turn the seat over and detach motors
from the mounting brackets.
NOTE:
The lower seat cushion must be
removed from the seat frame to access
the motor mounting screws on some
models.
2. Remove the drive cable from the motor gear boxes. Slide a shrink wrap tube
(3/4º diameter x 1.75º, 3M P/N 36596) on each end of the flex shaft, as shown in
the illustration.
The Camry and Sienna will require six (6) shrink tubes.
The Solara will require only one (1) shrink tube.
Camry/Sienna Solara
Front
3. Attach the drive cables to the motors and reinstall motors to the motor mounts.
4. Position each shrink wrap tube so that it overlaps the drive cable housing and motor
housing or gear box housing, as necessary.
5. Using a heat gun, apply heat to the
shrink tubes in a direction from the
center of the drive cable toward the
gear box or motor housing. Be sure to
apply just enough heat to shrink the
tubing.
6. Reinstall the seat cushion to the seat
frame. Tighten the mounting screws to
torque specifications listed in the BO
section of the Repair Manual.
7. Reinstall the seat assembly to the
floor of the vehicle. Assure all
connectors are secure and the power
seat adjustments properly function.
Torque: 37 Nm, 380 kgfcm, 27 ftlbs
Repair
Procedure
Heat Gun
Shrink Tube

DOOR MIRROR WIND NOISE ± BO019±99 December 3, 1999
Page 2 of 2
INCORRECT POSITION A INCORRECT POSITION B INCORRECT POSITION C
Mirror Housing
ConnectorGrommetMirror Housing
Mirror Housing
Grommet Grommet
ConnectorConnector
3. To reposition the grommet and/or
harness connector onto the mirror
housing:
Remove the mirror housing (3
nuts) from the door and carefully
unclip the mirror from the housing.
This will allow easier access and
reinstallation of the grommet
and/or harness connector.
Reposition the grommet so it is
fully seated to the mirror housing.
Assure the harness connector is
inside the grommet.
NOTE:
Refer to the 1998 Camry Repair Manual
pages BO±23 through BO±26.
4. Reinstall the door mirror and speaker
assembly:
Secure the mirror to the housing.
Properly align and reinstall the
mirror assembly to the door.
tighten the three nuts. Torque:
5.5 Nm (56 Kgfcm, 49 inlb)
Reinstall the door speaker (one
nut) and speaker cover onto the
door.
Assure the power mirror
adjustment and the door speaker
functions properly.
ConnectorRear View MirrorOutside Door
Mirror
Mirror Housing
Grommet
CORRECT POSITION
Repair
Procedure
CoverOutside Rear
View Mirror
Door Trim
Specified Torque Nm (kgfcm, ftlbf) :5.5 (55, 49, ftlbf)

SEAT COVER LOOSENESS ± BO020±99 December 17, 1999
Page 3 of 3
6. Reassemble the seat cushion.
7. Bend the locking tabs over the
cushion.
8. After reinstallation of the seat and
manual seat adjuster handle
(if removed), check the seat cushion
retention and seat operation
(sit on seat and push cushion down).
9. Tighten the seat mounting screws to
the torque specifications in the Repair
Manual.Repair
Procedure
(Continued)
Locking Tabs

BR002±94
BRAKE VIBRATION AND/OR PULSATIONPage 6 of 6
C. Phase Match Rotor To Hub
± If rotor runout is at the maximum value or greater, (refer to appropriate repair manual)
index the rotor one lug and measure the runout again. Repeat this process, moving the
rotor one lug each time, until the position is found where the runout is at the minimum and
within the maximum value listed in the appropriate repair manual
(See Figure 6 below).
± Tighten lug nuts to the specified torque following a star sequence when installing wheel
(See Figure 7 below).
Note: DO NOT USE AIR IMPACT WRENCH.
Four Holes Five Holes
Figure 7Figure 6

BRAKE PAD CLICKING NOISE ± BR004±00 October 20, 2000
Page 2 of 4
There are two types of brake calipers: floating and fixed. Check the type of brake caliper
installed on the vehicle by removing the wheel assembly.
1. Floating Type Brake Caliper
A. Lift up or remove the brake caliper
and suspend it securely.
HINT:
Do not disconnect the flexible hose
from the brake caliper.
B. If equipped with anti±squeal
spring: Remove the anti±squeal
springs.
C. Remove the brake pads with
anti±squeal shims.
D. Remove the pad support plates
from the torque plate. Clean any
dust from the pad support plates,
torque plates and brake pads.
E. Apply a small amount of the
disc brake caliper grease
(1±2 mm thick) to both sides
of the pad support plates.
NOTE:
Do NOT apply grease to the friction
surfaces of the brake pads or the
disc rotor.
F. If the pad support plate is fixed to
the torque plate with adhesive tape,
perform the operation according to
the following flow chart.
Without removing the pad
support plate, apply a small
amount of grease to the portion
where the pad touches the
surface of the support plate.Fixed firmly in placeThere is adhesive tape, but
it is not fixed firmly in placeAdhesive tape is peeled offRemove the pad support plate,
peel off the adhesive tape and
apply a small amount of grease to
both sides of the support plate.Remove the pad support plate
and apply a small amount of
grease to both sides of the
support plate.
Check whether or not the pad support plate
and the torque plate are fixed firmly in place
with adhesive tape.
Application
Procedure
Pad Support
PlatesTorque
Plate
Apply Disc Brake Caliper Grease
Pad Support Plates

DOOR MIRROR WIND NOISE ± NV007±00 March 31, 2000
Page 2 of 2
Examples of improperly installed assemblies are shown below:
ConnectorGrommet Mirror Housing
INCORRECT POSITION A
Connector
GrommetMirror Housing
INCORRECT POSITION B
Connector
GrommetMirror Housing
INCORRECT POSITION C
3. To reposition the grommet and/or
harness connector onto the mirror
housing:
Remove the mirror housing (the
remaining 2 nuts) from the door
and carefully unclip the mirror
from the housing. This will allow
easier access and reinstallation of
the grommet and/or harness
connector.
Reposition the grommet so it is
fully seated to the mirror housing.
Assure the harness connector is
inside the grommet.
NOTE:
Refer to the 1998 Camry Repair Manual
pages BO±23 through BO±26.
4. Reinstall the door mirror and speaker
assembly:
Secure the mirror to the housing.
Properly align and reinstall the
mirror assembly to the door.
Tighten the upper and forward
nuts. Torque: 5.5 Nm (56
Kgfcm, 49 inlb)
Reinstall the door speaker (one
nut at the lower bracket
) and
speaker cover onto the door as
shown in the illustration. Torque:
5.5 Nm (56 Kgfcm, 49 inlb)
Assure the power mirror
adjustment and the door speaker
functions properly.
NOTE:
Do NOT mount the UPPER speaker
bracket behind the nut.
Repair
Procedure
(Continued)
Rear View
Mirror
Grommet
CORRECT POSITIONOutside Door
Mirror
Mirror Housing
Connector
Cover
Door Trim
Nm (kgfcm, ftlbf) : Specified TorqueOutside Rear
View Mirror
5.5 (55, 49, ftlbf)
INCORRECTCORRECT

TOYOTA MOTOR SALES U.S.A., INC.
The following bolt mark and class identification information is currently not included in the Standard
Bolt Torque Specifications found in the Introduction section of each Toyota Repair Manual.
BOLT MARK CLASS
(Hexagon flange bolt or 4 Protruding Lines 9T
Hexagon bolt with washer)
(Hexagon flange bolt or 5 Protruding Lines 10T
Hexagon bolt with washer)
(Hexagon flange bolt or 6 Protruding Lines 11T
Hexagon bolt with washer)
SPECIFIED TORQUE FOR STANDARD BOLTS
SPECIFIED TORQUE
CLASS DIAMETER PITCH HEXAGON HEAD BOLT HEXAGON FLANGE BOLT
mm mm Nm kgfcm ftlbf Nm kgfcm ftlbf
8 1.25 34 340 25 37 380 27
9T 10 1.25 70 710 51 78 790 57
12 1.25 125 1300 94 140 1450 105
8 1.25 38 390 28 42 430 31
10T 10 1.25 78 800 58 88 890 64
12 1.25 140 1450 105 155 1600 116
8 1.25 42 430 31 47 480 35
11T 10 1.25 87 890 64 97 990 72
12 1.25 155 1600 116 175 1800 130
STANDARD BOLT TORQUE SPECIFICATIONSPage 1 of 1
PRODUCT GENERAL
INFORMATION
PG95-006
JULY 21, 1995
ALL MODELS