1999 TOYOTA AVENSIS Supplement

I04818
SPEEDOMETER
TACHOMETER
WATER TEMP.
FUEL
OIL LEVEL
ODO / TRIP
METER
OUTSIDE TEMP.
CLOCK
RHEOSTATLCD
DISPLAY
LCD
DISPLAY S
T
W
FA18
B7
B20 A5
A15
A3
A6
A7
A8
A12
A11
A19
A10
A9
B11
B24
B5
A22
B4
A23
B14
A23
A25
B16
B14
B21
A22
A14VOLTAGE
STABILIZER
B17
B22
B9
B26
A24 Brake Warning
Fuel filter Warning
Discharge Waring
Economy Indicator
Turbo / Glow Plug Indicator
Glow Plug Indicator
ABS Warning
Low Oil Pressure Warning
Check Engine Warning
O / D OFF Indicator
ECT SNOW Indicator
ECT PWR Indicator
Rear Fog Light Indicator
High Beam Indicator
Right Turn Indicator
Left Turn Indicator
Open Door Warning
SRS Warning
Front Fog light Indicator A1
B15
B18A26
B2
A17
B1
B13
B6
B3 B19
BE–4
– BODY ELECTRICALCOMBINATION METER

No.
AGround (Power)
Tacho Pick–UP Sensor
EFI ECU (3S–FE, 2C–TE Engine)
EGR (2C–T Engine)
Vehicle Speed Sensor
EFI ECU
Water Temperature Sender Gauge (2C–T Engine)
Ground (Engine)
Ground
Outside Temperature Sender Gauge
Ground (Fuel)
Fuel Sender Gauge
Ground (Power)
Ground (Speed)
Turn Signal Switch (Right)
Other Parts
Oil Level Warning Switch
O/D OFF Switch
ECT ECU (Gasoline Engine)
Fuel Filter Warning Switch (Diesel Engine)
Glow Plug Timer (Diesel Engine)
EFI ECU (Gasoline Engine)
ECT Pattern Select Switch
ABS ECU
Rear Fog Light Switch 1
3
5
6
7
8
9
10
11
12
14
15
17
18
19
21
22
23
24
25
26Wire Harness Side
1
2
3
4
5
6
7
9
11
13
14
15
16
17
18
19
20
22
24
26Turn Signal Switch (Left)
H–LP Fuse
Front Fog Light Switch
Alternator L Terminal
Brake Fluid Level Warning Switch
Parking Brake Switch
ECU+B Fuse
Taillight Relay
GAUGE Fuse
Ground (Signal)
DOOR Fuse
EFI ECU (Gasoline Engine)
EGR ECU (Diesel Engine)
Headlight Dimmer Switch
Low Oil Pressure Warning Switch
IGN Fuse
Door Courtesy Switch
Airbag ECU
Taillight Relay
GAUGE Fuse
Ground (Signal)
DOOR Fuse
B
– BODY ELECTRICALCOMBINATION METER
BE–5

BE199–02
I01273
1
2 3
BE–6
– BODY ELECTRICALCOMBINATION METER
INSPECTION
1. INSPECT SPEEDOMETER ON–VEHICLE
Using a speedometer tester, inspect the speedometer for allow-
able indication error and check the operation of the odometer.
HINT:
Tire wear and tire over or under inflation will increase the indica-
tion error.
Europe Models
(mph)(km/h)
Standard indication Allowable range Standard indication Allowable range
20 20 – 24.5 20 20 – 26
40 40 – 46.5 40 40 – 48
60 60 – 68.5 60 60 – 70
80 80 – 90.5 80 80 – 92
100 100 – 112.5 100 100 – 114
120 120 – 136
140 140 – 158
160 160 – 180
If error is excessive, replace the speedometer.
2. INSPECT VEHICLE SPEED SENSOR OPERATION
(a) Connect the positive (+) lead from battery to terminal 1
and negative (–) lead to terminal 2.
(b) Connect the positive (+) lead from tester to terminal 3 and
the negative (–) lead to terminal 2.
(c) Rotate the shaft.
(d) Check that the voltage changes from approx. 0 V to 11 V
or more between terminals 2 and 3.
HINT:
The voltage changes be 4 times every revolution of the speed
sensor shaft.
If operation is not as specified, replace the sensor.
3. INSPECT TACHOMETER/
ON–VEHICLE
(a) Connect a tune–up test tachometer, and start the engine.
NOTICE:

Reversing the connection of the tachometer will dam-
age the transistors and diodes inside.

When removing or installing the tachometer, be care-
ful not to drop or subject it to heavy shocks.

I01275
Ignition
Switch
BatterySender
Gauge Receiver
Gauge
I01276
Ignition
Switch
BatteryReceiver
Gauge
Test Bulb
(3.4 W)
I01277
Battery Ignition
SwitchWarning Light
Wire Harness Side
1
– BODY ELECTRICALCOMBINATION METER
BE–7
(b) Compare the tester and tachometer indications.
DC 13.5 V 25
C at (77
F)
Standard indicationAllowable range
700630 – 770
1,000900 – 1,100
2,0001,850 – 2,150
3,0002,800 – 3,200
4,0003,800 – 4,200
5,0004,800 – 5,200
6,0005,750 – 6,250
7,0006,700 – 7,300
4. INSPECT ENGINE COOLANT TEMPERATURE RE-
CEIVER GAUGE OPERATION
(a) Disconnect the connector from the sender gauge.
(b) Turn the ignition switch ON and check that the receiver
gauge needle indicates COOL.
(c) Ground terminal on the wire harness side connector
through a 3.4 W test bulb.
(d) Turn the ignition switch ON, and check that the bulb lights
up and the receiver gauge needle moves to the hot side.
If operation is as specified, replace the sender gauge.
Then recheck the system.
If operation is not as specified, measure the receiver gauge re-
sistance.
5. INSPECT LOW OIL PRESSURE WARNING LIGHT
(a) Disconnect the connector from the warning switch and
ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
If the warning light does not light up, test the bulb.

I01278
BE–8
– BODY ELECTRICALCOMBINATION METER
6. INSPECT LOW OIL PRESSURE SWITCH CONTINUITY
(a) Disconnect the connector from the switch.
(b) Check that continuity exists between terminal and ground
with the engine stopped.
(c) Check that no continuity exists between terminal and
ground with the engine running.
HINT:
Oil pressure should be over 24.5 kPa (0.25 kgf/cm
2, 3.55 psi).
If operation is not as specified, replace the switch.

BODY
CLIP BO–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WINDSHIELD BO–3. . . . . . . . . . . . . . . . . . . . . . . . . . .
SLIDING ROOF BO–11. . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL BO–13. . . . . . . . . . . . . . . . . . . .
ROOF HEADLINING (Sedan) BO–22. . . . . . . . . . . . . .
ROOF HEADLINING (Liftback) BO–27. . . . . . . . . . . . .
ROOF HEADLINING (Wagon) BO–32. . . . . . . . . . . . .
REFER TO AVENSIS/CORONA REPAIR MANUAL FOR
CHASSIS AND BODY (Pub. No. RM599E)
NOTE: The above pages contain only the points which differ
from the above listed manual.

BO19D–01
V00005
Clip RemoverPliers
Screwdriver
Scraper Shape (Example) Removal/Installation
– BODYCLIP
BO–1
CLIP
REPLACEMENT
The removal and installation methods of typical clips used in body parts are shown in the table below.
HINT:
If the clip is damaged during the operation, always replace it with a new clip.