1990 MITSUBISHI SPYDER clutch

-Transaxle
COMPONENTS
Lubricate all internal
parts with automatic
Itransmission fluid
during reassembly.
22200100127
1.Torque converter
assembly
Thrust washer 5.Front clutch assembly6.Thrust race
7.Thrust bearing 8.Thrust washer
9. Rear clutch assembly
10. Thrust bearing
11.Rear clutch hub
12. Thrust bearing
13. Thrust race 14. band15. drum
16.Snap ring
17. Center support
s p r i n g ,
1 9 . R e t u r n
20.Pressure plate
21.Brake
22.Brake23.Reaction plate:,.
24. Reverse sun gear25. Thrust bearing 26.Thrust race 27. sun 28. carrier. 29.Thrust bearing,30.Output flange..
TSBRevision

AUTOMATIC TRANSAXLE
OVERHAUL
Transaxle
3218
38 78
Nm
9 Nm 7
41
24 Nm
46
11 Nm8I
- -
42 during reassembly.
44. Oil temperature 45. Oil filter”
46: Valve body assembly
47. Manual control lever
48.
position switch (PNPswitch) End clutch’ shaft 50. Bearing retainer
51. Thrust bearing 52. End clutch 53. Thrust washer
54. End clutch assembly:
55. O-ring
31.Oil dipstick
32. Oil filler tube
33.Snap ring34. servo switch35.Snap ring
36. servo piston37.Spring
38.Anchor rod
39.Detent plate40. Manual control shaft 41. Parking roller support
42.Oil pan43.Gasket
TSB Revision

A U T O M A T I C T R A N S A X L E
OVERHAUL -Transaxle
56. End clutch cover57.Pulse58.Lock bolt59.Idler shaft60.Idler gear61.Spacer62.Gasket63. Idler gear cover
64. Differential bearing retainer
65.Spacer66. Differential front bearing cap
67.Differential assembly
6 8 . G a s k e t69. Differential cover70. Output retainer
71. Center differential assembly
72. Center bearing retainer’
73. Stopper ring
74. unit75. Center bearing retainer7 6 . F r o n t
77. Rear output shaft 78. Transaxle case
DISASSEMBLY
(1) Clean away any sand, mud,. etc. adhered the
transaxle.
(2) Place the transaxle assembly on the workbench w ith the
oil pan down.
(3) Remove the torque converter.
(4) Use the special tool to mount the dial gauge on trans-
axle case and the” play the .-
,
.
(5) Remove the pulse generator “A” and “B”.
(6) Remove the manual control lever, then remove th e
neutral position switch (PNP
(7)Remove the oil pan, magnets and gasket.

AUTOMATIC .
OVERHAUL
the cover the cover
the differential the differential
the differential bearing retainer,
.
,
differential,
.
end clutch cover
holder and end
the end clutch
a

AUTOMATIC TRANSAXLE
OVERHAUL
Transaxle
Thrust bearina
the input shaft and remove the front clutch assemb ly
and rear clutch assembly together.
thrust bearing
the clutch hub.
NOTE
The thrust race may be stuck to clutch hub.
thrust bearing
the drum.
TSB Revision

AUTOMATIC TRANSAXLE
OVERHAUL -Transaxle
thrust bearing and thrust
rear clutch.
the rear clutch assembly and the front
assembly..
thrust bearing on the rear clutch hub.
I
the rear clutch hub on the
thrust race onthe end of
the rear clutch hub.
TSB Revision

A U T O M A T I C T R A N S A X L E
OVERHAUL Transaxle
thrust bearing in the
. .
the. clutch assembly in the
__
the clutch assembly and drum into
transaxle case at the same time.
. .
I .
.. .
.
thrust race and thrust washer
of the oil pump with petrolatum.
the special tool to new
and oil pump assembly.
Oil pump assembly mounting 21
. ,
TSB RevisionI

A U T O M A T I C T R A N S A X L E
OVERHAUL -Transaxle
end play of the If not the standard
value, replace thrust race and thrust washer
adjust to the standard value.
Standard value: mm in.)
. . . the spacer, idler and then insert
the idler shaft.
Caution
Assemble so that the
groove ‘on
idler gear faces backward. ,
the idler shaft lock together
lock to the specified torque. Bend the three fingers
of the lock plate to prevent turning..
Idler shaft lock bolt: 38
the idler gear cover and a new
Idler gear cover(8
the end clutch shaft from the end with the long
.,
TSB RevisionI