1990 MITSUBISHI SPYDER coolant

ENGINE
Engine (Turbo)>
Pre-removal OperationlEngine Coolant Draining (Refer to GROUP 00 Maintenance Service.)
Post-installation.
lEngine Coolant Supplying and GROUP 00 l A/T Fluid Checking and Refilling if with (Refer to GROUP 00 Maintenance
8.710
6
Radiator removal steps
1. Drain plug
2. Radiator cap
3. Overflow tube
4. Reserve tank 5. Reserve tank bracket
u p p e r h o s e 8. Radiator lower hose 9. Transaxle cooler hose and assembly 13. Condenser fan motor assembly
fan motor assembly
Radiator fan motor
17. Shroud
Radiator fan motor removal steps
Transaxle fluid hose and
pipe. with fan motor assembly
f a n 17.
.
.
TSB

ENGINE Radiator
Pm-removal Operationl Engine Coolant Draining(Refer to GROUP 00 Maintenance Service.)II
Post-installation OperationlEngine Coolant Supplying and GROUP 00 Maintenance l Fluid Checking -andRefilling Necessary with (Refer to GROUP 00 Maintenance
12 Nm8.7
Radiator removal steps
1. Drain plug
2. Radiator cap
3. Overflow tube
4. Reserve tank
5. Reserve tank bracket
8. Radiator upper hose 7. Radiator lower hose8. Transaxle fluid cooler hose and pipe assembly with 9. Upper insulator10. Radiator assembly11. Lower insulator
12. Condenser fan motor assembly
fan motor assembly
Radiator fan motor16. Shroud
12
Radiator fan steps
4.
8. Transaxle fluid ‘hose and with 13. fan
14..
.
TSB Revision

ENGINE COOLING
T H E R M O S T A T
REMOVAL AND INSTALLATION
Pre-removal and Post-installation OperationEngine Coolant Draining and Supplying (Refer to
GROUP 00 Maintenance Service.)
lAir Hose(C) Removal and Installation Engine(Turbo)> (Refer to GROUP 15 -Charge Cooler.)II
Engine (Turbo)>
Ermine
16
Engine> - -
9.40 0 0 0 4 0 4 2
Removal steps
1. Radiator upper hose connection Engine (Non-turbo)> or
radiator lower hose connection
Engine and En-
-
3. Gasket Engine (Non-turbo)> 4. Thermostat
2.
outlet fitting Engine(Non-turbo)> orwater inlet fitting Engine
(Turbo) and Engine>
Revision

ENGINE COOLING Water Pump Engine (Non-turbo)>
WATER PUMP
ENGINE (NON-TURBO)>
REMOVAL AND INSTALLATION
and Post-Installation l Engine Coolant Draining and Supplying (Refer to
GROUP 00 Maintenance Service.)
l Timing Belt Rear Cover Removal and Installation
(Refer to GROUP
Timing Belt.)
.
12 Nm8.7
Removal steps
1. Water pump
2. O-ring
TSB Revision

E N G I N E C O O L I N G Water Pump Engine
P O I N T
O-RING INSTALLATION ,
Insert the O-ring to the and
of the O-ring with water or coolant.By with
water or engine coolant, the insertion the will become
easier.
Caution1.Do not allow engine oil or othei grease to to theO-ring.2. When inserting the water pump, check that there is no
sand, dirt, etc. on its inner surface’.
Revision

ENGINE COOLING Water Pump Engine (Turbo) and.
WATER PUMP ENGINE (TURBO) AND 1 4 1 0 0 2 7 0 1 5 5 ,
REMOVAL AND INSTALLATION
Pm-removal and Post-installation lEngine Coolant Draining and Supplying (Refer to
GROUP 00 Maintenance Service.)lFor Timinig Belt Removal and Installation,
Refer to the Following
GROUP Timing Belt.
GROUP Timing Belt.
,
12-15
TSB Revision
12-15
2417
12-15
Removal steps
1.Generator brace2.Waterpump
3. Water pump gasket4.O-ring

Water Pump Engine (Turbo) ENGINE COOLING
I N S T A L L A T I O N S E R V I C E P O I N T
O-RING INSTALLATION
Insert the O-ring to the water inlet pipe, and coat the outer
of the O-ring with or coating Water
or engine coolant, the insertion to the water pump will become easier.
Caution
1.Do not allow engine other grease to to the
O-ring.
2.When inserting the pipe, check that is’ no dirt,
etc. on its inner surface.
TSB Revision

Water: Hose and Water Pipe EngineE N G I N E C O O L I N G ( N o n - t u r b o ) >
WATER HOSE AND WATER PIPE
~ 4 1 0 0 5 5 0 1 1 5
REMOVAL AND INSTALLATION
Pre-removal and Post-installation OperationlEngine Coolant Draining and Supplying (Refer toGROUP 00 Service.)lUnder Cover Removal and Installation (Refer to
GROUP 42 Under Cover.)I I
3.92.9
7
33
Removal steps
1. Air intake hose
2. Air hose connection 7. Radiator fan motor assembly
8. Radiator lower hose connection
3. Control wiring harness connection
4. Water pipe assembly
5. Water hose6. Heater hose connection
9. Water hose10. Front exhaust pipe connection Water inlet pipe assembly 12. O-ring
TSB Revision