Page 377 of 402

u (0 ...... N r--. N ...... 0
0
:E
.. Or: pull sharply on the trim in the direction of
the arrow to remove
c:> fig. 295.
.. Insert the towing loop all the way into the
threaded opening and tighten it with a wheel
wrench .
.. After using, place the towing loop back in the
vehicle tool kit.
_& WARNING
If the towing loop is not tightened unti l it
stops when installing, the threads may be
pulled o ut when towing the vehicle and that
cou ld cause an acc ident .
(D Note
The trim is attached to the bumper with sev
eral hooks. To reduce the risk of damage, do
no t use any force when remov ing and instal
ling .
Rear towing loop
Fig. 296 Rear bumper: installi ng the tow ing loop
Vehicles with a towing loop
On vehicles w ithout a factory-installed trailer
hitch*, the towing loop threads a re located on
the right rear side of the bumper.
-
.,. Remove the tow ing loop from the veh icle tool
k it
c:> page 360 .
.. Press the cap inward wi th brief, forcef ul pres
s ur e
c:>fig. 296. The cap will loosen from the
bumper.
.. Inse rt the towing loop all the way into the
threaded opening and tighten it with a wheel
wrench .
.. After using, place the towing loop back in the
vehicle tool kit.
Emergency situations
Vehicles with a trailer hitch*
.. Attach the towing bar or the towing cable to
the trailer hitch.
Vehicles with a facto ry -installed trailer hitch* are
not equipped with towing loop threads at the
rear.
_& WARNING
If the towing loop is not tightened until it
stops when installing, the threads may be pulled out when towing the vehicle and that
could cause an accident.
_& WARNING
-Applies to: vehicles with trailer hitch
- Only use a spec ial towing bar to prevent
damaging the ball hitch. These towing bars
have been specially designed for trailer tow
i ng hitches.
- Only use special towing cables.
Loading the vehicle onto a flat bed truck
Fig. 297 Vehicle on flat bed truck
Front hook up
.. Align the vehicle with the centerline of the car
carrier ramp .
.,. Attach the w inch hook to the front towline eye
previously installed .
Rear hook up
.. Align the vehicle with the centerline of the car
carrier ramp.
.. Attach the w inch hook to the rear towline eye
previously installed . .,.
375
Page 378 of 402

Emergency situations
@ Tips
Check carefully to make sure the hook-up is
secure before moving the car up the flatbed
truck ramp.
Raising the vehicle
Lifting with workshop hoist and with floor
jack
The vehicle may only be li~ed at the lifting
poin ts illus trated .
Fig . 298 Front lift ing point
Fig . 299 Rear lifti ng po int
• Read and heed WARNING c::> .&_ .
• Locate lifting po ints c::> fig . 298 and ¢ fig. 299.
• Adjus t lifting arms of workshop ho ist o r floo r
ja ck to match veh icle lif ting poin ts.
• Inse rt a rubber pa d between t he f loor jack/
w ork shop hoist and the lifting poin ts.
If you must lift your vehicle with a floor jack to
work underneath , be sure the vehicle is safely
s upported on stands intended for this purpo se.
Front lifting point
The lift ing po int is located on the floor pan re in
forcement about at the same level as the jack
376
moun ting poin t c::> fig. 298 . Do not lift the vehi
cle at the ve rtical sill reinfo rcement.
Rear lifting point
The lifting poin t is lo cated on t he ve rti cal rein
fo rcemen t of t he lower s ill for the onboard j ack
¢fig. 2 99 .
Lifting with vehicle jack
Refer to c::> page 363.
A WARNING
-To r educe th e risk of s erious inju ry an d vehi
cle damage.
- Always lift the vehicle o nly at the special
workshop hoist and f loor jack lift points i l
l ustrated
c::> fig. 298 and c::> fig. 299.
- Failure to lift the ve hicle a t these points
could ca use the vehicle to tilt o r fall from
a lift if there is a change in ve hicle weight
dist ribution and balance . This might hap
pen, fo r example, whe n heavy compo
nen ts su ch as the eng in e b lock o r trans
mi ssion are removed.
- Whe n removing heavy co mponen ts lik e
these, anchor vehicle to hois t or ad d c orre
s p ondin g weights to maintai n the ce nt er of
g ra vity. Oth erw ise, the vehicle mig ht tilt or
slip off the hoist, ca using serio us persona l
in jur y.
(D Note
-Be aw are of the fo ll ow ing poi nts bef ore lift
ing the vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine oil pan, the transmission hous ing, the front
or rear axle or the body side members.
This could lead to serious damage .
- To avoid damage to the underbody or
chassis frame, a rubber pad must be in
serted between the floor jack and the lift
points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity of
the hoist. ..,.
Page 379 of 402
u co ...... N r-... N ...... 0
0
:E: '
-Before driving over a workshop hoist, en
sure that there is sufficient clearance be
tween the hoist and low parts of the ve
hicle.
Vehicle transport
A ppl ies to: ve hicles with a ir susp en sio n
The following contains information you should
know about transporting your vehicle.
Wh en transporting the vehicle on a ca r ca rri
er, tra in, sh ip or by ot her means , only t ie the
ve hicle down at t he r unnin g surface of the
tires, w hich i s t he outer circumference. Secur
ing the vehicle at the axle components, sus
p ens io n struts or tow ing eyes is no t per mitted
b ecause the pressure in the air suspens io n
str uts ca n cha nge dur in g tra ns port. Th e vehi
cle may no t be se cu red su ffici entl y if this ha p
pe ns.
Emergency situations
377
Page 380 of 402

Technical data
Technical data
Vehicle specifications
Fig. 300 Windsh iel d (fro nt left) : Ve hicl e Iden tific ation
N um ber ( VIN )
XXXXX XX -X -XXXX XXX XX
@-+ ~J:~t::1 ::: xxxxxxxx xx x xxxxxxxx
I YP lf'VPE XXX XXX
XX XXXXXXX XX X X XX
XXX
KW XXX
15\_L I MOIOlll
@-+ ~~
1
:tr:~i XXXX I XXXX XXX I XX
II. -AUSST . / OPTIONS
.__ __
E0A 7D5 4UB
2EH JOZ lLB
3FC
F0 A 9G3
TL6 3 KA 8EH
lXW 803
7T6 CV7 7KO
3L4 4KC
lS A 7GB
6XM SSG
lAS
SMU 7Xl
0G7 0YH
UlA X9B
908 8Z4
4X3 2K2
3Y0 413
01A
SRW
1BA
OJF
027
020
502
4G0
XX X XX X XX X XXXX
Fig . 301 Vehicle identificat ion lab el
Vehicle Identification Number (VIN) in the
Infotainment system
~ Select in the Infotainment system: the I MENU I
button > Vehicle > left contro l button > Service
& checks> Vehicle information.
Vehicle Identification Number (VIN)
The VIN can be found in the Infotainment sys
tem, on the vehicle data label, and under the
windshield on the front left side* <=:>
fig. 300 . The
VIN is also in the right side of the luggage com
partment (the fende r) under a cover.
378
Vehicle identification label
The vehicle identification label <=:> fig. 301 is locat
ed in the luggage compartment under the cargo
floor cover.
The information of the vehicle identification label
can also be found in your Warranty
& Mainte
nance booklet.
The st icker contains the follow ing vehicle data:
(D Vehicle Iden tifica tion Number (VIN)
@ Vehicle type, eng ine output, transmission
® Engine and transmission cod es
@ Paint and interior codes
® Optional equipment numbers
Safety compliance sticker
The safety compliance sticker is your assurance
that your new veh icle complies with all applicable
Federal Motor Vehicle Safety Standards which
were in effect at the time the vehicle was manu
factured. You can find this sticker on the driver's
s id e B-pillar .
It shows the month and year of pro
duction and the vehicl e identification number of
your vehicle (perfo ration) as well as the Gross Ve
hicle Weight Rating (GVWR) and the Gro ss Axle
Weight Rating (GAWR).
H igh voltage warning label
The high voltage warn ing label is located in the
e ngine compartment next to the engine hood re
lease. The spark ignit ion system complies w ith
the Canadian s tand ard IC ES-002.
Notes about technical
data
The values may vary based on special equipment
as well as market-specific equipment and meas
u ring methods.
Please note that the specifications listed in the
vehicle documentation a lways take precedence .
(D Tips
Missing technical data was not available at
the time of printing .
Page 381 of 402

u co ,....,
N r-... N ,....,
0
0
:E: '
Weights
Gross Vehi cle We ight Rating
The G ross Veh icle Weight Rating (GVWR) , and
the Gross Axle Weight Rating (GAWR) for front
and rear ar e listed on a sticker on the driver's side
B-pillar.
The G ross Veh icle Weight Rating includes the
weight of the basic vehicle p lus full fuel tank, oi l
and coolant, p lus maximum load, which includes
passeng er w eight (150 lbs/68 kg p er designated
seating position) and luggage we ight
c:> A .
Gross Axle Weight Rating
The Gross Axle We ight Rating is the max imum
l oad that can be applied at each axle of the vehi
cle
c:> &, .
Vehicle capacity weight
The vehicle capac ity we ight (max . load) is listed
on the drive r's side 8-p illar.
& WARNING
-
- T he act ual Gross Ax le Weight Rating at the
front and rear axles sho uld not exceed the
permissible weights, and their combination
must not exceed the Gross Vehicle We ight
Rating.
- Exceedi ng perm iss ible weight ratings can
result in vehicle damage, acc idents and per
sonal injury .
Dimensions
Technical data
(D Note
- The vehicle capacity weig ht figures apply
when the load is d istributed evenly in the
vehicle (passengers and luggage) . When
transport ing a heavy load in the luggage
compartment, carry the load as near to the
rear axle as possible so that the vehicle's
hand ling is no t impa ired .
- Do not exceed the maximum perm iss ible
ax le loads or the maximum g ross ve hicle
we igh t. A lways remember that the vehi cle's
hand ling will be affected by the extra load.
T he refore, adjust your speed acco rd ingly.
- Always observe lo cal regulations.
Length (in (mm)) Width (in (mm ))
Width across the Height at curb
mirrors (in (mm )) weight (in (mm))
Q7 199
.6 (5069) 7 7.5 (1968) 8 7.1 ( 2212) 68.5 (1740)
Capacities
Approximate capaci-
ties
Fuel tank 2
2.5 gal (85 L)
Windsh ield and headlight washer system* 7.4 qt (7 L)
379
Page 382 of 402

Tech nical data
Gasoline engines
Q7 2.0, 6 cylinder
Maximum output SAE net
M ax im um torq ue SAE net
Displacement
Engine oil with filter change
1>
Fuel
Q7 3.0, 6 cylinder
Maximum output SAE net
Maximum torque SAE net
Displacement
Engine oil with fi lter change
1
)
Fuel
Diesel engines
Q7 3 .0 TOI, 6 cylinder
Maximum output SA E net
Maximum torq ue SAE net
Displacement
Engine oil with filter change
1
)
Fuel
l ) For specific engine oil capac ities, please see
the mos t cur rent informa tion fo r the USA at
http ://www. audi usa.com/he lp/ma in tenance o r
for Canada a t ht tp://www.aud i.ca/ca/brand/ en/
your _aud i/ aud i_ services _a nd/Ca re _and _M a i nte
na nce/ schedule.htm l or call 800-822 -2834.
380
hp@ rpm 252 @ 5000 -6000
lb-ft@ rpm 272@
1600 - 4500
CID (cm
3
) 121 (1984)
¢ page 314, Gasoline
hp@ rpm 333@ 5500 -6500
lb -ft@ rpm 325@ 2900 - 5300
CID (cm
3 ) 183 (2995)
¢ page 314, Gasoline
hp@ rpm 258@ 3250 -4250
lb -ft@ rpm 443@ 1500 -3000
C ID (cm
3
) 181.1 ( 296 7)
ULSD No . 2 ¢ page 315, Diesel fuel
Page 383 of 402

u co ...... N r-... N ...... 0
0
:E: '
Consumer Information
Warranty coverages
Y our Audi is co vered b y the following war ran
tie s:
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfora-
tion
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Control Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regard ing your warranties
can be found in yo ur
W arranty & M ainten ance
bookl et.
Operating your vehicle
outside the U.S.A. or
Canada
Government reg ulations in the Un ited States and
Canada require that automobiles meet specific
emission regulations and safety standards.
Therefore, vehicles built for the U .S.A. and Cana
da d iffer from vehicles sold in other countries.
I f you p lan to take your vehicle outside the conti
nenta l limits of the United States or Canada,
there is the poss ibility that:
- u nleaded fue ls for vehicles with cata lytic con
verter may not be available;
- fuel may have a considerably lower octane rat
i ng . Imprope r fuel may ca use engine damage;
- service may be inadequate due to lack of p roper
service facilities, tools or testing eq uipment;
- r eplacement parts may not be readily ava ilable.
- Navigat ion systems for veh icles built for the
U .S .A . and Canada will not necessa rily work in
Eur ope, and may not wo rk in other countries
o utside of North Amer ica.
Consumer Inf ormation
(D Note
Audi cannot be respons ible for mechanical
damage that could resu lt from inadequate
fuel, service or parts ava ilability.
Audi Service Repair
Manuals and Literature
Audi Official Factory Service Manuals and L itera
ture are published as soon as poss ible after mod
el i ntroduction. Service Ma nua ls and literature
are avai lab le to order from the Audi Tec hni cal Lit
erature Orde ring Center at :
www.audi.t e chlit eratur e.com
Maintenance
General
Your vehicle has been designed to he lp keep
maintenance requirements to a min imum. How
ever, a certain amount of regular maintenance is
still necessary to assure your veh icle's safety,
economy and reliab ility . For detailed vehicle
maintenance consult your Wa rranty
& Mainte
nance boo klet .
Und er diff icult op erating condition s, for exam
ple at extremely low outside temperatures, in
very dusty regions, when towing a trai le r very fre
quently, etc., some se rvice work shou ld be pe r
fo rmed between the in terv als specified. This ap
plies particularly to:
- oil changes , and
- cleaning or replac ing the a ir filter .
(® For the sake of the environment
By regularly maintain ing your vehicle, you
help make sure that emiss ion standards are
maintai ned, thus min imizing adverse effects
on the environment .
Important considerations for you and your
vehicle
The increasing use of electronics, sophisticated
fuel injection and emission control systems, and
the genera lly increas ing techn ica l complexity of ""'
381
Page 384 of 402

Consumer Info rmation
today's a utomo biles, have steadily reduced the
scope of maintenance and repairs which can be
carried out by veh icle owners.
Also , sa fet y and
en vironmental
concerns place very strict limits
on the nature of repairs and adjustmen ts to en
g ine and transmission parts wh ich an owner can
perform .
Maintenance, adjustments and repairs usually re
qu ire special tools, testing devices and other
equ ipment available to specially trained work
shop personnel in order to assure proper per
forma nce, re liability and safety of the veh icle and
its many systems .
Improper maintenance, adjustments and repairs
can impair the operation and reliab ility of your
ve hicle and eve n void your vehicle warranty .
Therefo re, proof of se rvicing in a ccordance w ith
the m aintenance sched ule may be a condition for
up ho ld ing a possible wa rranty claim made within
the wa rranty pe riod.
Above all , ope rational safety can be adversely af
fected, cre ating unne cessa ry risks fo r you and
your passengers.
I f in doubt about any servicing, have it done by
your author ized Audi dealer or any other properly
eq uipped and qualified workshop . We strongly
urge you to g ive your author ized Audi dealer the
opportunity to perform a ll scheduled mainte
nance and necessa ry repairs. Your dealer has the
facilities, origina l parts and tra ined specialists to
keep your veh icle runn ing prope rly.
Performing limited maintenance yourself
The fo llow ing pages describe a limited number of
procedures whic h can be performed on your vehi
cle with ordinary tools, should the need arise and
tra ined personnel be unava ilable. Before per
forming any of these procedures, always thor
ough ly read all of the app licab le text and carefu l
ly follow the instructions g iven . A lways rigorously
observe the
WARNINGS prov ided .
Befo re yo u check anything in the engine com
partment, always read and heed all WARNINGS
c::> & and c::> & in Working in the engine compart
ment on page 322 .
382
A WARNING
-
-Ser ious personal in jury may occur as a result
of imp roperly performed maintenance, ad
justments or repairs .
- Always be extreme ly careful when work ing
on the vehicle . Always follow commonly ac
cepted safety practices and general com mon sense. Never r is k personal in jury.
- Do not attempt any of the mainte nance,
checks or repairs described on the following pages if you are no t fu lly fam iliar with these
or other proce dures with respect to the ve
hicle, o r are uncert ain how to p ro ceed.
- Do not do any work wi thout the prope r tools
a nd equi pmen t. H ave the necess ary wo rk
done by your authorized Au di dealer or an
other properly equipped and qualified work
shop.
- The engine compartment of any motor veh i
cle is a potentially hazardous area . Never
reach into the a rea around or touch the radi
ator fan. It is temperature controlled and
can switch on suddenly - even when the en
gine is off and the ignition key has been re
moved. The rad iator fan switches on auto
mat ica lly when the coolant reaches a certain
temperature and will con tinue to ru n until
the coolant temperat ure drops.
- Always remove the igni tion key before any
one gets u nder the vehicle.
- Always support your vehicle with safety
stands if it is necessary to work underneath
the vehicle. The ja ck* s upplied w ith the vehi
cle is no t ad equate fo r thi s pu rpose and
could collapse causing se rious personal in
jury .
- If you must wor k underne ath the vehicle
with the wheels on t he ground, always make
sure the vehicle is on level ground, that the
wheels a re always sec urely blocked and that
the engine cannot be started.
- Always make sure the transmission se lector
lever (automatic t ransm iss ion) is in P (Park
position) and the park b rake is applied.