2006 ACURA CSX lock


(#'
 )
Removal
19-171
VSA Modulator-Control Unit Removal and Installation
A C
B
I
E
F
G
H
J
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft) 9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
15 N·m (1.5 kgf·m, 11 lbf·ft)
D
22 N·m
(2.2 kgf·m, 16 lbf·ft)
NOTE: Do not spill brake fluid on the vehicle; it may damage the paint; if brake fluid gets on the paint, wash it off immediately with water.
 Be careful not to damage or deform the brake lines during removal and installation.
 Plug the ends of the hoses and the joints to prevent spilling brake fluid.
1. Turn the ignition switch to LOCK (0).
2. Disconnect the VSA modulator-control unit 37P connector (A) by pushing the lock (B) and pu lling down the lever
(C); the connector disconnects itself.
3. Disconnect the six brake lines from the VSA modulator-control unit. NOTE: Brake lines are connected to the master cylinder (D) and to the right-front (E), the left-rear (F), the right-rear
(G), and the left-front (H) brake systems.
4. Remove the VSA modulator-control unit (I) with the bracket (J) from the body.
5. Remove the VSA modulator-control unit from the bracket. (cont’d)
08/08/21 15:06:47 61SNR030_190_0171
ProCarManuals.com
DYNOMITE -2009-


(#'

 ) Special Tools Required
Front
19-173
Wheel Speed Sensor Replacement
A
B
C9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
Guide pin tool 07AAG-SVBA100
1. Turn the ignition switch to LOCK (0).
2. Release the clamp (A), then disconnect the wheel speed sensor connector (B).
3. Remove the clips, the bolt, and the wheel speed sensor (C).
4. Install the wheel speed sensor in the reverse order of removal, and note these items:  Install the sensor carefully to avoid twisting the wires.
 If the wheel speed sensor comes in contact with the wheel bearing, it is faulty, investigate the cause beforereplacing the sensor.
5. Start the engine, and make sure the ABS and the VSA indicators go off.
6. Test-drive the vehicle, and make sure the ABS and the VSA indicators do not come on.
(cont’d)
08/08/21 15:06:47 61SNR030_190_0173
ProCarManuals.com
DYNOMITE -2009-

Î
Rear
19-174VSA System Components
Wheel Speed Sensor Replacement (cont’d)
Right side
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft) A
B
C
1. Turn the ignition switch to LOCK (0).
2. Release the clamp (A), then disconnect the wheel speed sensor connector (B).
3. Remove the clips, the bolt, and the wheel speed sensor (C).
08/08/21 15:06:47 61SNR030_190_0174
ProCarManuals.com
DYNOMITE -2009-

(#'
/)
Body
Doors
Mirrors
Glass
MoonroofInterior Trim
Consoles
Dashboard
.............................................. ..............................................
Special Tools . 20-2
............................................ ..
.... ...
................
...........................................
........................................... ...
..... ....
..................
...........................................
........................................... .......
.............................................
............................................. ............................................
..
.... ...
................
...........................................
........................................... ...
..... ....
..................
...........................................
........................................... .......
.............................................
.............................................
Component Location Index
- Front Door . 20-3
Component Location Index - Rear Door . 20-5
Front Door Panel Removal/Installation . 20-7
Front Door Outer Handle Replacement . 20-9
Front Door Latch Replacement . 20-12
Front Door Glass and Regulator Replacement . 20-14
Front Door Glass Outer Weatherstrip Replacement . 20-15
Front Door Weatherstrip Replacement . 20-16
Rear Door Panel Removal/Installation . 20-17
Rear Door Outer Handle Replacement . 20-19
Rear Door Latch Replacement . 20-21
Rear Door Glass and Regulator Replacement . 20-23
Rear Door Glass Outer Weatherstrip Replacement . 20-26
Rear Door Weatherstrip Replacement . 20-27
Front and Rear Door Glass Adjustment . 20-28
Front and Rear Door Position Adjustment . 20-29
Front and Rear Door Striker Adjustment . 20-31
......................
......................
.......................................
......................
......................
......................
.................
Component Location Index . 20-32
Power Mirror Replacement . 20-33
Mirror Holder Replacement . 20-34
Rearview Mirror Replacement . 20-35
......................
.......................... .............
...................... ......................
.......................... .............
......................
Component Location Index
. 20-36
Windshield Replacement . 20-38
Front Corner Glass Replacement . 20-43
Rear Window Replacement . 20-47
...................... ............
.......................
.................................... ....................
.....................
............................
................................... .......
......................... ..
......................
............
.......................
.................................... ....................
.....................
............................
................................... .......
......................... ..
Component Location Index
. 20-53
Symptom Troubleshooting Index . 20-54
Glass Position Adjustment . 20-55
Glass Replacement . 20-55
Wind Deflector Replacement . 20-56
Drain Channel Replacement . 20-57
Sunshade Replacement . 20-58
Motor Replacement . 20-59
Frame and Drain Tube Replacement . 20-60
Drain Channel Slider and Cable Assembly Replacement . 20-62
Closing Force and Opening Drag Check . 20-64 ......................
..
..
.................................... ..
.....
...........
................
.................................. ......................
..
..
.................................... ..
.....
...........
................
..................................
Component Location Index
. 20-65
Trim Removal/Installation - Door Areas . 20-66
Trim Removal/Installation - Pillar Areas . 20-69
Trim Removal/Installation - Rear Shelf Area . 20-78
Trim Removal/Installation - Trunk Area . 20-80
Trim Removal/Installation - Trunk Lid . 20-82
Grab Handle Removal/Installation . 20-82
Headliner Removal/Installation . 20-84
Carpet Replacement . 20-88
......
..................... ....
...................... ......
..................... ....
......................
Center Console Removal/Installation . 20-92
Center Console
Disassembly/Reassembly . 20-95
Center Console Armrest Replacement . 20-96
Armrest Lock Replacement . 20-96
..............................
.............................. ...
..............................
.............................. .........
.............................. ....................
...............
..............................
..............................
.............................. .....................
..............................
..............................
...
..............................
.............................. .........
.............................. ....................
...............
..............................
..............................
.............................. .....................
Instrument Panel
Removal/Installation . 20-98
Gauge Control Module (Speedo) Trim Removal/Installation . 20-99
Subdisplay Visor Removal/Installation . 20-100
Driver’s Dashboard Lower Cover Removal/Installation . 20-102
Driver’s Dashboard Undercover Removal/Installation . 20-103
Center Pocket Removal/Installation . 20-103
Passenger’s Dashboard Undercover Removal/Installation . 20-104
Glove Box Removal/Installation . 20-104
Dashboard Vent Removal/Installation . 20-105
Glove Box Striker Replacement . 20-107
Dashboard Side Trim Removal/Installation . 20-107
Side Defogger Vent Trim Removal/Installation . 20-108
Dashboard/Steering Hanger Beam Removal/Installation . 20-108
Dashboard/Steering Hanger Beam Disassembly/Reassembly . 20-114
08/08/21 14:58:49 61SNR030_200_0002
ProCarManuals.com
DYNOMITE -2009-

Seats
Bumpers
Hood
Trunk Lid
Fuel Fill Door
Exterior TrimFenderwell
Openers
Frame......................
............................................... ...............
................ .......
........................................... .........................
..............................
........................................... ......................
........................................... ...
...
......................
............................................... ...............
................ .......
........................................... .........................
..............................
........................................... ......................
........................................... ...
...
Component Location Index
. 20-116
Front Seat Active Head Restraint Inspection . 20-117
Front Seat Removal/Installation . 20-118
Front Seat Frame Replacement . 20-120
Front Seat-back Cover Replacement . 20-123
Front Seat Cushion Cover Replacement . 20-127
Rear Seat Removal/Installation . 20-131
Rear Seat-back Latch Replacement . 20-135
Rear Seat-back Release Lever/Cable Removal/Installation . 20-136
Rear Seat Armrest Beverage Holder Replacement . 20-137
Rear Seat Armrest Replacement . 20-138
Rear Seat-back Cover Replacement . 20-139
Rear Seat Side Bolster Cover Replacement . 20-143
Rear Seat Cushion Cover Replacement . 20-143
Rear Seat Armrest Cover Replacement . 20-144
.........
...........................................
........................................... ..........
........................................... .........
...........................................
........................................... ..........
...........................................
Front Bumper Removal/Installation . 20-146
Front Bumper Lower Grille
Replacement . 20-148
Front Bumper Lower Side Plate Replacement . 20-148
Rear Bumper Removal/Installation . 20-149
Rear Bumper Lower Cover Replacement . 20-151
...................................... ................................................
......................................
................................................
Hood Adjustment
. 20-152
Hood Seal Replacement . 20-153
Hood Insulator Replacement . 20-154
................................ ..............
..............
................................
..............
..............
Trunk Lid Adjustment
. 20-155
Trunk Lid Torsion Bar Replacement . 20-156
Trunk Lid Weatherstrip Replacement . 20-157
Trunk Lid Cushion Replacement . 20-157
.........................................
.........................
................
Fuel Fill Door Adjustment
. 20-158
Fuel Cap Adapter Replacement . 20-159
........................................
...............
.......................... ......................
...................... ...
..............
................
..................
..........................
..............
...............
.......................... ......................
...................... ...
..............
................
..................
Front Grille Replacement
. 20-160
Front Fender Trim Replacement . 20-162
Front Grille Cover Replacement . 20-163
Cowl Cover Replacement . 20-163
Roof Molding Replacement . 20-165
Door Molding Replacement . 20-167
Side Sill Protection Tape Replacement . 20-168
Rear License Trim Replacement . 20-168
Trunk Lid Spoiler Replacement . 20-169
Emblem/Sticker Replacement . 20-170 .............
...................... ............
......
.............
.............
......................... .................... .............
...................... ............
......
.............
.............
......................... ....................
Front Inner Fender Replacement . 20-171
Splash Shield Replacement
. 20-172
Front Fender Fairing Replacement . 20-173
Middle Floor Undercover Replacement . 20-174
Rear Floor Undercover Replacement . 20-174
Fuel Pipe Protector Replacement . 20-175
Rear Fender Cover Replacement . 20-175
Rear Strake Replacement . 20-176
Rear Air Outlet Replacement . 20-176
...................... ............
..................
..........................
........................................... .....
...................
......................
............
..................
..........................
........................................... .....
...................
Component Location Index
. 20-177
Hood Opener Cable Replacement . 20-178
Trunk Lid Opener Cable/Fuel Fill Door Opener Cable Replacement . 20-179
Hood Latch Replacement . 20-181
Trunk Lid Opener/Fuel Fill Door Opener Replacement . 20-182
Trunk Lid Lock Cylinder Replacement . 20-184
Trunk Lid Latch Replacement . 20-185
...........................................
........................................... ............................
...................................
...........................................
...........................................
............................
...................................
Upper Dashboard Support Gusset
Replacement . 20-186
Rear Floor Upper Cross-member Gusset Replacement . 20-186
Subframe Replacement . 20-187
Frame Repair Chart . 20-188
08/08/21 14:58:49 61SNR030_200_0003
ProCarManuals.com
DYNOMITE -2009-



(#'



 )
20-920-9
Front Door Outer Handle
Replacement
A B
62 mm (2.44 in.)
A
B C
B
A
10. Install the door panel in the r everse order of
removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Replace any damaged cable fasteners with new ones.
 The latch cable (A) should be fixed to the cable fastener (B) with the latch in lock position.
 Make sure the connectors are plugged in properly, and the cables are connected securely.
 Make sure the window and power door lock operate properly. NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel and inner handle (see page 20-7).
3. Disconnect the power door lock actuator connector (A).
4. Remove the plug caps (B), then remove the plastic cover (C), as needed.
5. Detach the rod fastener (A).
(cont’d)
08/08/21 14:58:59 61SNR030_200_0011
ProCarManuals.com
DYNOMITE -2009-



(#'



 )
20-920-9
Front Door Outer Handle
Replacement
A B
62 mm (2.44 in.)
A
B C
B
A
10. Install the door panel in the r everse order of
removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Replace any damaged cable fasteners with new ones.
 The latch cable (A) should be fixed to the cable fastener (B) with the latch in lock position.
 Make sure the connectors are plugged in properly, and the cables are connected securely.
 Make sure the window and power door lock operate properly. NOTE: Put on gloves to protect your hands.
1. Raise the glass fully.
2. Remove the door panel and inner handle (see page 20-7).
3. Disconnect the power door lock actuator connector (A).
4. Remove the plug caps (B), then remove the plastic cover (C), as needed.
5. Detach the rod fastener (A).
(cont’d)
08/08/21 14:58:59 61SNR030_200_0011
ProCarManuals.com
DYNOMITE -2009-


Î
20-11
Fastener Locations
:Screw,2
A
B
C
D D
A
A B
A
A
10. If necessary, remove the special screws, then separate the door cylinder (A) and the outer handle
protector (B). If the retainer (C) is damaged, release
the hooks (D), and replace it.
NOTE: If removed, the special screws must be
replaced.
11. While pulling the outer handle (A), remove the handle from the holes in the door panel. Take care
not to scratch the door. 12. Remove the rod fastener (A) from the outer handle
(B), then replace it with a new one.
13. Install the handle in the reverse order of removal, and note these items:
 Make sure the cylinder cable and each rod is connected securely.
 Make sure the door key cylinder/door locks operate properly.
 Make sure the door handle works properly.
 When reinstalling the door panel, make sure the
plastic cover is installed properly and sealed
around its outside perimeter to seal out water.
 Check for water leaks (see step 9 on page 20-29).
Replace.
08/08/21 14:59:00 61SNR030_200_0013
ProCarManuals.com
DYNOMITE -2009-