2006 ACURA CSX Engine filter

µµ
µµµµµµ
µµ
µµ
•••
µµ
µµ
µµ
µµ
µµ
µµ
µµ
µµ
Engine Lubrication
Item Measurement QualificationStandard or New Service Limit
2-5
Engine oil Capacity (K20Z2) Engine overhaul 5.3 L (5.6 US qt)
Oil change
including filter 4.2L(4.4USqt)
Oil change
without filter 4.0L(4.2USqt)
Capacity (K20Z3) Engine overhaul 5.5 L (5.8 US qt)
Oil change
including filter 4.4L(4.6USqt)
Oil change
without filter 4.2L(4.4USqt)
Oil pump Inner-to-outer rotor clearance 0.06 0.16 mm (0.002 0.006 in.) 0.20 mm (0.008 in.)
Pump housing-to-outer rotor clearance 0.15 0.21 mm (0.006 0.008 in.) 0.23 mm (0.009 in.)
Pump housing-to-rotor axial clearance 0.035 0.070 mm (0.0014 0.0028 in.) 0.12 mm (0.005 in.)
Balancer shafts, journal diameter No. 1 journal, front shaft19.938 19.950 mm (0.7850 0.7854 in.) 19.92 mm (0.784 in.)
No. 1 journal,
rear shaft 23.938 23.950 mm (0.9424 0.9429 in.) 23.92 mm (0.942 in.)
No. 2 journal,
front and rear
shaft 32.949 32.961 mm (1.2972 1.2977 in.) 32.93 mm (1.296 in.)
Balancer shafts, journal taper 0.005 mm (0.0002 in.) max.
Balancer shafts, end play Front0.063 0.108 mm (0.0025 0.0043 in.) 0.14 mm (0.0055 in.)
Rear 0.063 0.108 mm (0.0025 0.0043 in.) 0.14 mm (0.0055 in.)
Balancer shafts, shaft-to-bearing
clearance No. 1 journal,
front shaft0.050 0.082 mm (0.0020 0.0032 in.) 0.10 mm (0.004 in.)
No. 1 journal,
rear shaft 0.050 0.082 mm (0.0020 0.0032 in.) 0.10 mm (0.004 in.)
No. 2 journal,
front and rear
shaft 0.060 0.120 mm (0.0024 0.0047 in.) 0.15 mm (0.006 in.)
Balancer shaft bearings, I.D. No. 1 journal,
front shaft 20.000 20.020 mm (0.7874 0.7882 in.) 20.03 mm (0.789 in.)
No. 1 journal,
rear shaft 24.000 24.020 mm (0.9449 0.9457 in.) 24.03 mm (0.946 in.)
No. 2 journal,
front and rear
shaft 33.021 33.069 mm (1.3000 1.3019 in.) 33.09 mm (1.303 in.)
Relief valve, oil pressure with oil
temperature at 80 °C (176 °F) At idle
70 kPa (0.7 kgf/cm , 10 psi) min.
At 3,000 rpm 300 kPa (3.1 kgf/cm , 44 psi) min.
2
2
08/08/21 14:07:14 61SNR030_020_0005
ProCarManuals.com
DYNOMITE -2009-

(#')Symbol Maintenance Main Items
3-7
Maintenance Main Items
If the message ‘‘SERVICE’’ does not appear more than 12 months after the display is reset, change the engine oil every
year.
NOTE:


 Replace the brake fluid every 3 years independent of the maintenance messages in the information display.
Inspect idle speed every 160,000 miles (256,000 km).
Adjust the valves during services A, B, 1, 2 or 3, only if they are noisy.

















A Replace engine oil (see page 8-10).
Engine oil capacity without oil filter:
K20Z2: 4.0 L (4.2 US qt)
K20Z3: 4.2 L (4.4 US qt)
B Replace engine oil and oil filter (see page 8-11). Engine oil capacity with oil filter:
K20Z2: 4.2 L (4.4 US qt)
K20Z3: 4.4 L (4.6 US qt)
Check front and rear brakes (see page 19-3). Check pad and disc for wear (thickness), damage, and cracks.
Check calipers for damage, leaks, and tightness of mounting bolts.
Check parking brake adjustment (see page 19-7). Check the number of clicks (8 to 10) when the parking brake lever is pulled with 196 N (20 kgf,
44 lbf) of force.
Inspect tie-rod ends, steering gearbox, and gearbox boots (see page 17-5). Check steering linkage.
Check boots for damage and leaking grease.
Check fluid lines for damage and leaks.
Inspect suspension components (see page 18-3). Check bolts for tightness.
Check condition of ball joint boots for deterioration and damage.
Inspect driveshaft boots (see page 16-4). Check boots for cracks and boot bands for tightness.
Inspect brake hoses and lines including VSA lines (see page 19-37). Check the master cylinder and VSA modulator-control unit for damage or leakage.
Inspect all fluid levels and condition of fluids. Engine coolant (see page 10-7)
Automatic transmission fluid (ATF-Z1) (see page 14-231)
Manual transmission fluid (MTF)
5M/T (see page 13-5), 6M/T (see page 13-82)
Clutch fluid (see page 12-7)
Brake fluid (see page 19-9)
Windshield washer fluid (see page 22-234)
Inspect exhaust system: K20Z2 (see page 9-13), K20Z3 (see page 9-14)
Check catalytic converter heat shields, exhaust pipes, and muffler for damage, leaks, and tightness.
Inspect fuel lines (see page 11-326) and connections (see page 11-328). Check for loose connections, cra cks, and deterioration; retighten loose connections and replace
damaged parts.
NOTE: According to state and federal regulations, failure to do the maintenance items marked with an asterisk ( ) will
not void the client’s emissions warranties. However, Acura recommends that all maintenance services be done at the
recommended interval, to ensure long-term reliability.
08/08/21 14:08:32 61SNR030_030_0007
ProCarManuals.com
DYNOMITE -2009-

µµ µµ
µµ µµ
(#')
Number Maintenance Sub Items
3-8
Maintenance Minder
Maintenance Sub Items
1 Rotate tires, and check tire inflation and condition.
Follow the pattern shown in the Owner’s Manual.


2 Replace air cleaner element (see page 11-346).
Replace every 15,000 miles (24,000 km) if the vehicle is driven in dusty conditions.
Replace dust and pollen filter (see page 21-75). If the vehicle is driven mostly in urban areas that have high concentrations of dust, pollen, or soot in
the air, replace every 15,000 miles (24,000 km).
Replace the filter whenever airflow from the heating and air c onditioning system is less than normal.
Inspect drive belt (see page 4-30). Look for cracks and damage, then check the position of the drive belt auto-tensioner indicator.
3 Replace automatic transmission fluid (see page 14-232). Capacity:2.9L(3.1USqt);useAcuraATF-Z1.
Replace manual transmission fluid. 5M/T (see page 13-5), 6M/T (see page 13-82)
Capacity:1.5L(1.6USqt);useAcuraMTF.




4 Replace spark plugs (see page 4-21).
K20Z2: Use SKJ20DR-M11 (DENSO).
K20Z3: Use SK22PR-M11S (DENSO).
Inspect valve clearance (cold). K20Z2 (see page 6-12)
Intake: 0.21 0.25 mm (0.008 0.010 in.), Exhaust: 0.28 0.32 mm (0.011 0.013 in.)
K20Z3 (see page 6-14)
Intake: 0.21 0.25 mm (0.008 0.010 in.), Exhaust: 0.25 0.29 mm (0.010 0.011 in.)


5 Replace engine coolant (see page 10-8).
Capacity (including the reservoir):
K20Z2: M/T 4.3 L (1.14 US gal), A/T 4.2 L (1.11 US gal)
K20Z3: 4.5 L (1.19 US gal)
Use Honda Long Life Antifreeze/Coolant Type 2.
08/08/21 14:08:32 61SNR030_030_0008
ProCarManuals.com
DYNOMITE -2009-

(#')
Symptom Diagnostic procedure Also check for
4-4
Starting System
Symptom Troubleshooting Index


Engine does not start
(does not crank)
1.
2.
3.
4.
5.
6.
7.Check for loose battery terminals or connections.
Test the battery for a low state of charge (see page
22-67).
Check the starter (see page 4-6).
Check the starter cut relay (see page 22-70).
Check the clutch interlock switch (M/T model) (see page
4-8).
Check the transmission range switch (A/T model)
(see page 14-265).
Check the ignition switch or wire (see page 22-72). Poor ground at G101
(A/T model) or G401
(M/T model)
Engine cranks, but does
not start 1.
2.
3.
4.
5.
6.
7.
8.
9.Check for PGM-FI DTCs (see page 11-3).
Check for IMMOBI status and function (see page
22-325).
Check the fuel pressure (see page 11-325).
Check for a plugged or damaged fuel line (see page
11-326).
Check for a plugged fuel filter (see page 11-337).
Check the throttle body (see page 11-
343).
Check for low engine compression (see page 6-7).
Check for a damage or broken cam chain (see page
6-21).
Do the engine control module (ECM)/powertrain control
module (PCM) reset in the PGM-FI INSPECTION menu
to cancel the ALL INJECTORS STOP with the Honda
Diagnostic System (HDS). Empty fuel tank
Weak or fouled spark
plugs
Engine is hard to start 1. 2.
3.
4.Check for PGM-FI DTCs (see page 11-3).
Check the fuel pressure (see page 11-325).
Check for a plugged or damaged fuel line (see page
11-326).
Check for a plugged fuel filter (see page 11-337). Weak or fouled spark
plugs
Engine cranks slowly 1. 2.
3.
4.Check for loose battery terminals or connections.
Test the battery for a low state of charge (see page
22-67).
Check the starter for binding (see page 4-13).
Check for excessive drag in the engine.
08/08/21 14:09:21 61SNR030_040_0005
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
7-11
Oil Pan Removal
1. If the engine is already out of the vehicle, go to step 18.
2. Raise the vehicle on the lift.
3. Drain the engine oil (see page 8-10).
4. Remove the front wheels.
5. Remove the splash shield (see step 25 on page 5-5).
6. Separate the stabilizer links (see page 18-25).
7. Separate the knuckles from the lower arms (see step 6 on page 18-21).
8. Remove the steering gearbox bracket. Remove the steering gearbox mounting bolt, the stiffener
mounting bolt, and the stiffener (see step 36 on
page 5-6).
9. Remove the steering gearbox mounting bolt, the stiffener mounting bolt, and the stiffener. Remove
the harness clamp from the front subframe (see
step 38 on page 5-6).
10. A/T model: Remove the bolt securing the automatic transmission fluid (ATF) filter.
11. Install the front leg assembly, the hook, and the wing nut to an A and Reds engine support hanger
(AAR-T1256) onto the 2006 Civic engine hanger
(VSB02C000025). Carefully position the engine
hanger on the vehicle, and attach the hook to the
slotted hole in the support eyelet. Tighten the wing
nut by hand to lift and support the engine/
transmission (see step 47 on page 5-8). 12. Remove the lower torque rod (see step 49 on page
5-8).
13. M/T model: Remove the front mount mounting bolt (see step 50 on page 5-9).
14. Make the appropriate reference line at both sides of the front subframe that line up with the edges on
the body (see step 51 on page 5-9).
15. Loosen the mid-stiffener mounting bolts on both sides(seestep52onpage5-9).
16. Attach the front subframe adapter (VSB02C000016) to the front subframe, and hang the belt of the front
subframe adapter over the front of the subframe.
Secure the belt with its stop, then tighten the wing
nut (see step 53 on page 5-9).
17. Remove the front subframe (see step 55 on page 5-10).
18. Remove the lower torque rod bracket.
(cont’d)
08/08/21 14:32:34 61SNR030_070_0011
ProCarManuals.com
DYNOMITE -2009-


7-31
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft)
19. Raise the vehicle on the lift.
20. Install the lower torque rod, then tighten the newlower torque rod mounting bolts in the numbered
sequence shown (see step 21 on page 5-18).
21. M/T model: Loosely tighten the new front mount mounting bolt (see step 22 on page 5-19).
22. Lower the vehicle on the lift.
23. Remove the engine support hanger and engine hanger adapter.
24. Tighten the upper torque rod mounting bolt (see step 25 on page 5-19).
25. Raise the vehicle on the lift.
26. M/T model: Tighten the front mount mounting bolt (see step 27 on page 5-19).
27. A/T model: Install the bolt securing the automatic transmission fluid (ATF) filter. 28. Install the stiffener, then tighten the steering
gearbox mounting bolt and the stiffener mounting
bolt. Install the harness clamp to the front subframe
(see step 29 on page 5-20).
29. Install the steering gearbox bracket. Install the stiffener, then tighten the steering gearbox
mounting bolt and the stiffener mounting bolt (see
step 32 on page 5-20).
30. Connect the lower arms to the knuckles (see step 9 on page 18-16).
31. Connect the stab ilizer links (see page 18-25).
32. Install the splash shield (see step 40 on page 5-20).
33. Install the front wheels.
34. Refill the engine with engine oil (see step 4 on page 8-10).
08/08/21 14:33:12 61SNR030_070_0031
ProCarManuals.com
DYNOMITE -2009-

(#'
/)
Engine Mechanical
Engine Lubrication
...................................................................................................................................... ..............
.......................................... .........................................
............................................. ..............................
.......................................................... ................................................................................................................
..............................................
....................................................
......................................................... ......................................................
................................................................
...................................................................... ..............
.......................................... .........................................
............................................. ..............................
.......................................................... ................................................................................................................
..............................................
....................................................
......................................................... ......................................................
Special Tools . 8-2
Component Location Index . 8-3
Symptom Troubleshooting Index . 8-5
Low Oil Pressure Indicator Circuit Diagram . 8-6
Low Oil Pressure Indicator Circuit
Troubleshooting (Open) . 8-7
Low Oil Pressure Indicator Circuit Troubleshooting (Short) . 8-8
Oil Pressure Switch Test . 8-9
Oil Pressure Switch Replacement . 8-9
Oil Pressure Test . 8-10
Engine Oil Replacement . 8-10
Engine Oil Filter Replacement . 8-11
Oil Filter Feed Pipe Replacement . 8-12
Oil Cooler Replacement . 8-13
Oil Jet Replacement . 8-13
Oil Jet Inspection . 8-14
Oil Pump Overhaul . 8-15
08/08/21 14:36:35 61SNR030_080_0001
ProCarManuals.com
DYNOMITE -2009-


(#'
%)Ref. No. Tool Number Description Qty
8-2
Engine Lubrication
Special Tools
07HAA-PJ70101
Oil Filter Wrench 1
08/08/21 14:36:35 61SNR030_080_0002
ProCarManuals.com
DYNOMITE -2009-