2005 NISSAN NAVARA control unit

CONTROL UNIT CONFIGURATION PROCEDURE
GI-39
C
D
E
F
G
H
I
J
K
L
MB
GI
R51/D40 (SPEC1)
*:For UK models
Touch “BACK” on “READ CONFIGURATION” screen.
PKIC1798E
PKIC1799E

GI-40
CONTROL UNIT CONFIGURATION PROCEDURE
R51/D40 (SPEC2)
*:Except for UK models
Touch “BACK” on “READ CONFIGURATION” screen.
PKIC1792E
PKIC1793E

CONTROL UNIT CONFIGURATION PROCEDURE
GI-41
C
D
E
F
G
H
I
J
K
L
MB
GI
WRITE CONFIGURATION PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1. With ignition switch OFF, connect CONSULT-II and CONSULT-II
CONVERTER to data link connector, and then turn ignition
switch ON.
2. Touch “START (NISSAN BASED VHCL)”.
3. Touch “BCM” on “SELECT SYSTEM” screen.
If “BCM” is not indicated, refer toGI-50, "
CONSULT-II Data Link
Connector (DLC) Circuit"in “GI” section.
4. Touch “BCM” on “SELECT TEST ITEM” screen.
PKIC0644E
BCIA0029E
BCIA0030E
PKIA5226E

GI-42
CONTROL UNIT CONFIGURATION PROCEDURE
5. Touch “CONFIGURATION” on “SELECT DIAG MODE” screen.
6. Touch “R51/D40 (SPEC1)” (for UK models) or “R51/D40
(SPEC2)” (Except for UK models) and “OK” on “VEHICLE
SELECT” screen.
For canceling, touch “CANCEL” on “VEHICLE SELECT” screen.
*: Nissan Anti-Theft System
7. Touch “WRITE CONFIGURATION” on “SELECT CONFIG
ITEM” screen.
8. Touch YES”.
For canceling, touch “NO”.
9. Using the following flow chart, identify the correct model and configuration list. Confirm and/or change set-
ting value for each item according to the configuration list.
PKIB1959E
PKIC1790E
PKIC1791E
PKIB1962E

CONTROL UNIT CONFIGURATION PROCEDURE
GI-43
C
D
E
F
G
H
I
J
K
L
MB
GI
R51/D40 (SPEC1)
l*:For UK models
R51/D40 (SPEC2)
l*:Except for UK models
10. Touch “CHNG SETTING” on “WRITE CONFIGURATION” screen.
CAUTION:
Make sure to touch “CHNG SETTING” even if the indicated configuration of brand-new BCM is
same as the desirable configuration.
If not, configuration which is set automatically by selecting vehicle model cannot be memorized.
PKIC1800E
PKIC1794E

GI-44
CONTROL UNIT CONFIGURATION PROCEDURE
11. Touch “OK” on “WRITE CONFIGURATION” screen.
lR51/D40 (SPEC1)
lR51/D40 (SPEC2)
If “CANCEL” is touched, it will return to previous screen.
12. Wait until the next screen during setting.
lR51/D40 (SPEC1)
lR51/D40 (SPEC2)
13. WRITE CONFIGURATION results are printed out automatically. Confirm “WRITE CONFIGURATION” is
correctly executed by comparing sheet automatically printed out with applicable configuration list shown in
step 9.
PKIC1801E
PKIC1795E
PKIC1802E
PKIC1796E

CONTROL UNIT CONFIGURATION PROCEDURE
GI-45
C
D
E
F
G
H
I
J
K
L
MB
GI
lR51/D40 (SPEC1)
lR51/D40 (SPEC2)
14. Touch “OK” on “WRITE CONFIGURATION” screen.
lR51/D40 (SPEC1)
PKIC1798E
PKIC1792E
PKIC1803E

GI-46
CONTROL UNIT CONFIGURATION PROCEDURE
lR51/D40 (SPEC2)
WRITE CONFIGURATION is completed.
PKIC1797E