Page 436 of 1897

H12118
BO-20
- BODYREAR DOOR
1805 Author: Date:
2001 AVALON (RM808U)
13. REMOVE REAR DOOR GLASS
(a) Open the door glass until the bolts appear in the service
hole.
(b) Remove the 2 bolts.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
NOTICE:
Be careful not to drop the door glass.
(c) Pull the door glass upward to remove it.
14. REMOVE WINDOW REGULATOR ASSEMBLY
(a) Disconnect the connector, then remove the 4 nuts and
window regulator assembly.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
HINT:
Remove the window regulator assembly through the service
hole.
(b) Using a torx driver, remove the 3 torx screws and window
regulator motor from the window regulator guide assem-
bly.
HINT:
At the time of reassembly, please refer to the following
items.
Apply MP grease to the glass guide and rollers of window
regulator assembly.
After installing the window regulator assembly, window
regulator assembly need to be re-initialized.
Refer to BE-80.
15. REMOVE DOOR LOCK
(a) Disconnect the control link from the outside handle.
(b) Disconnect the connector.
(c) Remove the 3 torx screws and door lock.
Torque:
Bolt: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
Screw: 4.9 N´m (50 kgf´cm, 43 in.´lbf)
HINT:
Remove the door lock through the service hole.
HINT:
At the time of reassembly, please refer to the following item.
Apply adhesive to 3 screws.
Part No. 08833-00070, THREE BOND 1324 or equiva-
lent
(d) Remove the 2 screws and door lock protector from the
door lock.
Page 437 of 1897
H12119
- BODYREAR DOOR
BO-21
1806 Author: Date:
2001 AVALON (RM808U)
HINT:
At the time of reassembly, please refer to the following item.
Apply MP grease to the sliding and rotating parts of the door
lock.
16. REMOVE OUTSIDE HANDLE
Remove the 2 bolts and outside handle.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
Page 439 of 1897
BO2QD-01
H12219
Center Armrest
Seat Cushion Pad
with Frame Seat Cushion Cover
Center Armrest Bracket
Center Armrest Hinge
Hog Ring
Shoulder Belt Guide
Headrest
Headrest Support
Headrest Support
Seatback Pad with Frame
Hog Ring
N´m (kgf´cm, ft´lbf): Specified torque
Non-reusable partSeatback Cover
5.9 (60, 52 in.´lbf)
18 (185, 13)
41 (420, 30)
18 (185, 13)
- BODYREAR SEAT
BO-1 19
1904 Author: Date:
2001 AVALON (RM808U)
REAR SEAT
COMPONENTS
Page 440 of 1897
BO2QF-01
H03147
- BODYREAR SEAT
BO-121
1906 Author: Date:
2001 AVALON (RM808U)
DISASSEMBLY
1. REMOVE HEADRESTS
2. REMOVE CENTER ARMREST
Remove the 2 nuts and center armrest.
Torque: 5.9 N´m (60 kgf´cm, 52 in.´lbf)
3. REMOVE SHOULDER BELT GUIDES
Remove the 4 screws and 2 shoulder belt guides.
4. REMOVE HEADREST SUPPORTS
5. REMOVE SEATBACK COVER
Remove the hog rings and seatback cover from the seatback
pad with frame.
6. REMOVE SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat
cushion pad.
Page 443 of 1897
BO2QE-01
H13186
H12220
BO-120
- BODYREAR SEAT
1905 Author: Date:
2001 AVALON (RM808U)
REMOVAL
1. REMOVE REAR SEAT CUSHION ASSEMBLY
Remove the rear seat cushion.
2. REMOVE REAR SEATBACK ASSEMBLY
(a) Remove the 4 bolts.
Torque:
Center: 41 N´m (420 kgf´cm, 30 ft´lbf)
LH, RH Side: 18 N´m (185 kgf´cm, 13 ft´lbf)
(b) Raise the seatback assembly upward to remove the seat-
back assembly.
Page 444 of 1897
BO2PZ-01
H12201
Roof Headlining
Roof Side Inner Garnish
Front Seat Outer
Belt Floor Anchor
Front Door
Opening Trim Assist Grip
w/ Rear personal light:
Rear Personal Light
Roof
Console
Box
Map Light Lens
Assist Grip
Sun Visor
Holder
Front Pillar Garnish
Front Door Scuff
Inside Plate
Center Pillar GarnishLensRoom Light
RH Rear Seat Inner
with Center Belt
Rear Door
Opening Trim
Lower Center
Pillar GarnishInside Rear Door
Scuff Plate
Rear Seatback
LH Rear Seat Inner
with Center Belt
Rear Seat Cushion
w/ Sliding roof:
Roof HeadliningSliding Roof
Opening Trim
41 (420, 30)
Lap Belt Outer Anchor Cover
41 (420, 30)
18 (185, 13)
18 (185, 13)
41 (420, 30)
: Specified torqueN´m (kgf´cm, ft´lbf)Cover
Cover
BO-98
- BODYROOF HEADLINING
1883 Author: Date:
2001 AVALON (RM808U)
ROOF HEADLINING
COMPONENTS
Page 447 of 1897

H12175
H12198
H12199
:5 Clips
H12200Clip
H121452 Clips BO-100
- BODYROOF HEADLINING
1885 Author: Date:
2001 AVALON (RM808U)
7. REMOVE FRONT DOOR SCUFF INSIDE PLATE
(a) Remove the front door scuff inside plate.
(b) Employ the same manner described above to the other
side.
8. REMOVE FRONT DOOR OPENING TRIMS
9. REMOVE LOWER CENTER PILLAR GARNISH
(a) Using a screwdriver, remove the lap belt outer anchor
cover.
(b) Remove the front seat outer belt floor anchor.
Torque: 41 N´m (420 kgf´cm, 30 ft´lbf)
(c) Remove the lower center pillar garnish as shown in the il-
lustration.
(d) Employ the same manner described above to the other
side.
10. REMOVE CENTER PILLAR GARNISH
(a) Remove the 2 clips.
(b) Using a screwdriver, remove the center pillar garnish.
HINT:
Tape the screwdriver tip before use.
(c) Employ the same manner described above to the other
side.
11. REMOVE FRONT PILLAR GARNISH
(a) Remove the front pillar garnish.
(b) Employ the same manner described above to the other
side.
Page 456 of 1897

BO2QO-01
H11075
- BODYSEAT BELT PRETENSIONER
BO-137
1922 Author: Date:
2001 AVALON (RM808U)
INSTALLATION
NOTICE:
Never use seat belt pretensioner from another ve-
hicle. When replacing parts, replace them with new
parts.
Make sure that the front seat outer belt is installed in
the specified torque.
If the front seat outer belt has been dropped, or there
are cracks, dents or any identified other defects in the
case or connector, replace the front seat outer belt
with a new one.
When installing the front seat outer belt, take care that
the wiring does not interfere with other parts and is
not pinched between other parts.
1. INSTALL RETRACTOR OF FRONT SEAT OUTER BELT
(a) Install the retractor of front seat outer belt with the 2 bolts.
Torque:
Upper bolt: 7.5 N´m (76 kgf´cm, 66 in.´lbf)
Lower bolt: 41 N´m (420 kgf´cm, 30 ft´lbf)
(b) Connect the pretensioner connector as shown in the il-
lustration.
2. INSTALL FRONT SEAT OUTER BELT SHOULDER AN-
CHOR
Torque: 41 N´m (420 kgf´cm, 30 ft´lbf)
3. INSTALL CENTER PILLAR GARNISH
4. INSTALL LOWER CENTER PILLAR GARNISH
5. INSTALL FRONT SEAT OUTER BELT FLOOR AN-
CHOR
Torque: 41 N´m (420 kgf´cm, 30 ft´lbf)
6. INSTALL FRONT DOOR SCUFF INSIDE PLATE