1997 TOYOTA SUPRA lock

BO0R0-01
N08453
BO5232
BO1689
BO-32
- BODYWINDSHIELD
2112 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE THESE PARTS:
(a) Inner rear view mirror
(b) Sun visors and holders
(c) Assist grip (See page BO-61)
HINT:
Tape a screwdriver tip before use.
(d) Front pillar garnishes (See page BO-61)
(e) Wiper arms and blades
(f) Cowl top ventilator louver
2. REMOVE WINDSHIELD MOULDING
(a) Using a knife, cut off the moulding as shown.
(b) Cut away the adhesive at the moulding installation area
as much as possible.
NOTICE:
Do not damage the body with the knife.
3. REMOVE WINDSHIELD GLASS
(a) Push piano wire through from the interior.
(b) Tie both wire ends to a wooden block or similar object.
HINT:
Apply adhesive tape to the outer surface of the glass to keep
the surface from being scratched.
NOTICE:
When separating the glass, take care not to damage the
paint and interior and exterior ornaments. To prevent
scratching the instrument panel when removing the wind-
shield, place a plastic sheet between the piano wire and
instrument panel.
(c) Cut the adhesive by pulling the piano wire around it.
(d) Remove the glass.
NOTICE:
Leave as much of the adhesive on the body as possible
when cutting off the glass.

N08522
N08520
N08521
1
Retainer
2
3
N08523
- BODYQUARTER WINDOW GLASS
BO-39
2119 Author
: Date
:
1997 SUPRA (RM502U)
4. REMOVE QUARTER WINDOW GLASS
(a) Remove the 3 nuts.
(b) Push piano wire through from the interior.
(c) Tie both wire ends to a wooden block or similar object.
HINT:
Apply adhesive tape to the outer surface to keep the surface
from being scratched.
NOTICE:
When separating the glass, take care not to damage the
paint and exterior.
(d) Cut the adhesive by pulling the piano wire around it.
HINT:
Cut the adhesive areas in the order as shown in the illustration,
so leave the adhesive where the glass retainer stays.
(e) Let the piano wire pass as shown on the illustration, cut
off the adhered part to the pin.
NOTICE:
Do not damage the glass retainers.
(f) Remove the glass.
NOTICE:
Leave as much of the adhesive on the body as possible
when cutting off the glass.

BO0R6-01
N19394

Removable Roof Moulding RH

Roof Side Rail Weatherstrip RH
Removable Roof PanelShim
Bracket No.2 RH
Bracket No.2 LHShim
Roof Headlining
Removable Roof Lock

Roof Side Rail Weatherstrip LH

Removable Roof Moulding LH

Non-reusable part BO-46
- BODYSPORT ROOF
2126 Author
: Date
:
1997 SUPRA (RM502U)
COMPONENTS

BO0R7-01
- BODYSPORT ROOF
BO-47
2127 Author
: Date
:
1997 SUPRA (RM502U)
DISASSEMBLY
REMOVE THESE PARTS:
(a) Roof side rail weatherstrip
(b) Removable roof moulding
(c) Roof headlining
(d) Removable roof lock
(e) Bracket No.2

BO0R9-01
N09281Seal Packing
N11800Butyl Tape
- BODYSPORT ROOF
BO-49
2129 Author
: Date
:
1997 SUPRA (RM502U)
REASSEMBLY
1. INSTALL THESE PARTS:
(a) Bracket No.2
(b) Removable roof lock
(c) Roof headlining
(d) Removable roof moulding
2. APPLY SEAL PACKING
Apply seal packing on the removable roof moulding as shown
in the illustration.
L: 4 mm (0.16 in.)
Part No. 08826-00080 or equivalent
3. INSTALL ROOF SIDE RAIL WEATHERSTRIP

N11812
No.1 Pin
Defroster Nozzle No.1 Garnish
Defroster Nozzle
Defroster Lower Nozzle
Heater to Register No.3 Duct
Instrument Panel Wire Harness KKKKKK
K
Solar Sensor
Room Temperature Sensor
Heater to Register No.4 DuctJ
Tweeter Speaker RH K
K
K
K
K
KK Tweeter Speaker LH
Side Defroster
No.1 Nozzle
Heater to Register
No.1 DuctNo.3 Register
Instrument Panel
Heater to Register No.5 Duct
No.4 Register
Theft Deterrent and
Door Lock ECU
PPS ECU K BO-52
- BODYINSTRUMENT PANEL
2132 Author
: Date
:
1997 SUPRA (RM502U)

BO0RC-02
- BODYINSTRUMENT PANEL
BO-57
2137 Author
: Date
:
1997 SUPRA (RM502U)
DISASSEMBLY
1. REMOVE THESE PARTS FROM INSTRUMENT PANEL
(a) Defroster nozzle No.1 garnish
(b) Defroster nozzle
(c) Defroster lower nozzle
(d) Heater to register No.3 duct
(e) Solar sensor
(f) Tweeter speakers
(g) Side defroster No.1 nozzle
(h) Heater to register No.5 duct
(i) No.4 register
(j) Heater to register No.1 duct
(k) No.3 register
(l) Room temperature sensor
(m) Theft deterrent and door lock ECU
(n) PPS ECU
(o) No.1 pins
2. REMOVE INSTRUMENT PANEL WIRE HARNESS

BO0RO-01
N16673
Luggage Compartment Mat
Seatback Lock KnobSeatback Board
Lock Knob Cover
Reclining Control
Cable LH Seatback Frame Reclining Control Cable RH
Tension Spring
Reclining Adjuster
Cover RH
Reclining
Adjuster RH
Reclining Adjuster
Cover LH
Tension Spring
Reclining Adjuster LH
Seatback Pad

Hog Ring
Seatback Cover
Seat Cushion Pad
Seat Cushion Cover

Non-reusable part
25 (260, 19)
18 (185, 13)
N´m (kgf´cm, ft´lbf): Specified torque BO-66
- BODYREAR SEAT
2146 Author
: Date
:
1997 SUPRA (RM502U)
REAR SEAT
COMPONENTS