1997 TOYOTA SUPRA drain bolt

MT06O-01
Q04417
Q06365
Q09475
Filler Plug
Drain PlugOil Level
0 - 5 mm
Q04419
R06858
- MANUAL TRANSMISSION (V160)MANUAL TRANSMISSION UNIT
MT-3
1571 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE UPPER CONSOLE PANEL, SHIFT LEVER
BOOT RETAINER AND SHIFT AND SELECT LEVER
BOOTS NO.1 AND NO.2
(a) Remove the shift lever knob.
(b) Using a screwdriver, pry out the upper console panel.
(c) Remove the 4 bolts and boot retainer.
(d) Remove the shift and select lever boots No.1 and No.2.
2. REMOVE 4 TRANSMISSION SHIFT LEVER SET
BOLTS
Torque: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
3. RAISE VEHICLE
NOTICE:
Make sure that the vehicle is securely supported.
4. DRAIN TRANSMISSION OIL
Oil type: TOYOTA GEAR OIL V160 or ESSO ATF
DEXRON®D-21065
Capacity: 1.8 liters (1.9 US qts, 1.6 Imp. qts)
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
5. REMOVE ENGINE UNDER COVER
6. REMOVE EXHAUST FRONT PIPE AND PIPE SUP-
PORT BRACKET
(a) Remove the 2 nuts, cover, oxygen sensor and gasket.
Torque: 20 N´m (200 kgf´cm, 14 ft´lbf)
(b) Remove the 2 bolts, nuts and gasket.
Torque: 58 N´m (590 kgf´cm, 43 ft´lbf)
(c) Remove the 2 bolts and pipe support bracket from the
clutch housing.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
(d) Remove the 2 bolts, nuts and gasket.
Torque: 58 N´m (590 kgf´cm, 43 ft´lbf)
(e) Remove the exhaust front pipe.

AC0QC-01
N08378
I03519
- AIR CONDITIONINGAIR CONDITIONING UNIT
AC-25
2173 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. DISCHARGE REFRIGERANT FROM REFRIGERANT
SYSTEM
HINT:
At the time of installation, please refer to the following item.
Evacuate air from refrigeration system.
Charge system with the refrigerant and inspect for leakage of
refrigerant.
Specified amount: 700 ± 50 g (24.96 ± 1.76 oz.)
2. DRAIN ENGINE COOLANT FROM RADIATOR
HINT:
It is not necessary to drain out all coolant.
3. REMOVE THESE PARTS:
(a) Engine wire harness bracket mounting bolt
(b) Brake tube bracket mounting bolts
4. DISCONNECT WATER HOSE FROM HEATER RADIA-
TOR PIPES
(a) Using priers, grip the claw of the hose clip and slide the
clip along the hose.
(b) Disconnect the water hoses from heater radiator pipes.
5. REMOVE INSULATOR RETAINER
Remove the 2 bolts and the insulator retainer.

N08379
N08536
N09037
I03520
AC-26
- AIR CONDITIONINGAIR CONDITIONING UNIT
2174 Author
: Date
:
1997 SUPRA (RM502U)
6. REMOVE LIQUID TUBE AND SUCTION TUBE
(a) Remove the ABS actuator.
(See page BR-70)
(b) Remove the bolt and slide the plate, then disconnect the
both tubes.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
NOTICE:
Cap the open fittings immediately to keep moisture or dirt
out of the system.
HINT:
At the time of installation, please refer to the following item.
Lubricante 2 new O-rings with compressor oil and install tubes.
7. REMOVE PLATE COVER
Remove the 2 bolts and the plate cover.
8. REMOVE INSTRUMENT PANEL AND REINFORCE-
MEN
(See page BO-50)
9. REMOVE HEATER TO REGISTER NO.3 DUCT
Remove the 3 screws and the heater to radister No.3 duct.
10. REMOVE A/C UNIT
(a) Disconnect connecters from the A/C unit.
(b) Remove the 6 bolts and the A/C unit.
HINT:
At the time of installation, please refer to the following item.
Pull the drain hose of the A/C unit forward until the yellow paint
on the hose is visible in the engine compartment.
Insert the drain hose into the engine compartment hose until the
matchmarks are aligned.

BR0GZ-01
R07130
R07131
- BRAKEFRONT BRAKE CALIPER (2JZ-GTE)
BR-37
1837 Author
: Date
:
1997 SUPRA (RM502U)
REMOVAL
1. REMOVE FRONT WHEEL
2. DISCONNECT FLEXIBLE HOSE
(a) Remove the union bolt and 2 gaskets from the caliper,
then disconnect the flexible hose from the caliper.
Torque: 30 N´m (310 kgf´cm, 22 ft´lbf)
HINT:
At the time of installation, please refer to the following item.
Install the flexible hose lock securely in the lock hole in the cali-
per.
(b) Use a container to catch the brake fluid as it drains out.
3. REMOVE CALIPER
Remove the 2 mounting bolts and caliper.
Torque: 118 N´m (1,200 kgf´cm, 87 ft´lbf)
4. REMOVE THESE PARTS
(a) Clip and 2 pins
(b) Anti-rattle spring
(c) 2 pads
(d) 2 pad spacers and anti-squeal shims

P25846
Drain Hose
- COOLINGWATER PUMP
CO-9
1422 Author
: Date
:
1997 SUPRA (RM502U)
(f) Remove the 6 bolts, water pump and gasket.
(g) Remove the drain hose.
(h) Remove the O-ring from the cylinder block.

CO08O-01
P03945
New
O-Ring
P02574
New Gasket
S00913
A
B A
B
AB
BB
- COOLINGWATER PUMP
CO-1 1
1424 Author
: Date
:
1997 SUPRA (RM502U)
INSTALLATION
1. INSTALL WATER PUMP
(a) Install a new O-ring to the cylinder block.
(b) Install the drain hose.
(c) Install a new gasket to the water pump.
(d) Connect the water pump to the water bypass pipe. Do not
install the nut yet.
(e) Install the water pump with the 2 bolts (A) and 4 bolts (B).
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
HINT:
Hand tighten the (A) bolts first.
(f) Install the 2 nuts holding the No.2 water bypass pipe to
the water pump.
Torque: 21 N´m (210 kgf´cm, 15 ft´lbf)
(g) 2JZ-GTE:
Connect the No.3 turbo water hose to the water pump.
(h) 2JZ-GE:
Install the connector bracket (for crankshaft position sen-
sor connector) with the bolt.
(i) 2JZ-GE:
Install the engine clamp bracket with the bolt.
(j) Install the generator with the bolt and nut.
Torque: 40 N´m (400 kgf´cm, 30 ft´lbf)
2. 2JZ-GE:
INSTALL NO.1 WATER BYPASS PIPE AND
WATER BYPASS OUTLET
(a) Install 2 new O-rings to the No.1 water bypass pipe.
(b) Install a new O-ring and the water bypass outlet with the
2 bolts.
Torque: 9.0 N´m (90 kgf´cm, 80 in.´lbf)
3. 2JZ-GTE:
INSTALL NO.1 WATER BYPASS PIPE AND
WATER OUTLET
(a) Install 2 new O-rings to the No.1 water bypass pipe.
(b) Apply soapy water to the O-rings.
(c) Install the No.1 water bypass pipe to the water pump.

P11908
(A)
Z16741
Drain
Hose
ECT Switch (2JZ-GTE)
S05171
- COOLINGRADIATOR
CO-23
1436 Author
: Date
:
1997 SUPRA (RM502U)
10. REMOVE RADIATOR ASSEMBLY
(a) 2JZ-GTE:
Disconnect the ECT switch (for electric cooling fan con-
nector) and wire harness.
(b) 2JZ-GTE:
Disconnect the 2 electric cooling fan connectors and wire
harness.
(c) Remove the bolt and upper radiator support. Remove the
2 upper radiator supports.
HINT:
At the time of installation, please refer to the following items.
Check that the rubber cushion (A) of the support is not de-
pressed.
Torque: 15 N´m (155 kgf´cm, 11 ft´lbf)
(d) Lift out the radiator assembly.
(e) Remove the 2 lower radiator supports.
11. REMOVE DRAIN HOSE FROM RADIATOR
12. 2JZ-GTE:
REMOVE ENGINE COOLANT TEMPERATURE (ECT)
SWITCH FROM RADIATOR
(a) Remove the ECT switch.
HINT:
At the time of installation, please refer to the following item.
Apply soapy water to the O-ring, and install the ECT switch.
Torque: 7.4 N´m (75 kgf´cm, 65 in.´lbf)
(b) Remove the O-ring from the ECT switch.
HINT:
At the time of installation, please refer to the following item.
Use a new O-ring.
13. REMOVE NO.1 FAN SHROUD FROM RADIATOR
(a) 2JZ-GE:
Remove the 4 bolts and No.1 fan shroud.
(b) 2JZ-GTE:
Remove the 5 bolts and No.1 fan shroud.

P02648
H
P04580
SST
B02745
Clearance
Lock
Plate
O-Ring
- COOLINGRADIATOR
CO-27
1440 Author
: Date
:
1997 SUPRA (RM502U)
(b) Check the lock plate height (H) after completing the caulk-
ing.
Plate height:
7.40 - 7.80 mm (0.2959 - 0.3119 in)
If not within the specified height, adjust the stopper bolt of the
handle again and caulk again.
6. INSPECT FOR WATER LEAKS
(a) Tighten the drain plug.
(b) Plug the inlet and outlet pipes of the radiator with SST.
SST 09230-01010
(c) Using a radiator cap tester, apply pressure to the radiator.
Test pressure:
177 kPa (1.8 kgf/cm
2, 26 psi)
(d) Inspect for water leaks.
HINT:
On radiators with resin tanks, there is a clearance between the
tank and lock plate where a minute amount of air will remain,
giving the appearance of an air leak when the radiator is sub-
merged in water. Therefore, before doing the water leak test,
move the radiator around in the water until all air bubbles disap-
pear.
7. INSTALL CUSHIONS TO RADIATOR