1997 TOYOTA SUPRA warning

Illustration:
what to do and where
21. CHECK PISTON STROKE OF OVERDRIVE BRAKE
(a) Place SST and a dial indicator onto the overdrive brake
piston as shown in the illustration.
Task heading : what to do
SST 09350-30020 (09350-06120)
Set part No. Component part No.
Detailed text : how to do task
(b) Measure the stroke applying and releasing the compressed
Piston stroke: 1.40
1.70 mm (0.0551
0.0669 in.)
Specification
air (392 - 785 kPa, 4 - 8 kgf.cm2 or 57 - 114 psi) as
shown in the illustration. IN-2
- INTRODUCTIONHOW TO USE THIS MANUAL
2 Author
: Date
:
1997 SUPRA (RM502U)
The procedures are presented in a step-by-step format:

The illustration shows what to do and where to do it.

The task heading tells what to do.

The detailed text tells how to perform the task and gives other information such as specifications
and warnings.
Example:
This format provides the experienced technician with a FAST TRACK to the information needed. The upper
case task heading can be read at a glance when necessary, and the text below it provides detailed informa-
tion. Important specifications and warnings always stand out in bold type.
6. REFERENCES
References have been kept to a minimum. However, when they are required you are given the page to refer
to.
7. SPECIFICATIONS
Specifications are presented in bold type throughout the text where needed. You never have to leave the
procedure to look up your specifications. They are also found in Service Specifications section, for quick
reference.

CAUTIONS are presented in bold type, and indicate there is a possibility of injury to you or other
people.

NOTICES are also presented in bold type, and indicate the possibility of damage to the compo-
nents being repaired.

HINTS are separated from the text but do not appear in bold. They provide additional information
to help you perform the repair efficiently.
8. SI UNIT
The UNITS given in this manual are primarily expressed according to the SI UNIT (International System of
Unit), and alternately expressed in the metric system and in the English System.
Example:
Torque: 30 N´m (310 kgf´cm, 22 ft´lbf)

B02917
- INTRODUCTIONFOR ALL OF VEHICLES
IN-1 1
11 Author
: Date
:
1997 SUPRA (RM502U)
(3) Even in cases of a minor collision where the SRS
does not deploy, the steering wheel pad, front pas-
senger airbag assembly and front airbag sensor
should be inspected (See page SR- 8, RS- 22,
RS-34).
(4) Never use SRS parts from another vehicle. When
replacing parts, replace them with new parts.
(5) Before repairs, remove the airbag sensor if shocks
are likely to be applied to the sensor during repairs.
(6) Never disassemble and repair the airbag sensor as-
sembly, steering wheel pad or front passenger air-
bag assembly in order to reuse it.
(7) If the airbag sensor assembly, steering wheel pad
or front passenger airbag assembly have been
dropped, or if there are cracks, dents or other de-
fects in the case, bracket or connector, replace
them with new ones.
(8) Do not expose the airbag sensor assembly, steer-
ing wheel pad and front passenger airbag assembly
directly to hot air or flames.
(9) Use a volt/ohmmeter with high impedance (10 kW/V
minimum) for troubleshooting of the electrical cir-
cuit.
(10) Information labels are attached to the periphery of
the SRS components. Follow the instructions on
the notices.
(11) After work on the supplemental restraint system is
completed, check the SRS warning light (See page
RS-1).
(c) SPIRAL CABLE (in Combination Switch)
The steering wheel must be fitted correctly to the steering
column with the spiral cable at the neutral position, other-
wise cable disconnection and other troubles may result.
Refer to of this manual concerning correct steering wheel
installation.

36SUPRAÐNEW FEATURES
3) ABS ECU
a. Wheel Speed Control
The ECU constantly receives signals form the 4±speed sensors and a deceleration sensor (2JZ±GTE engine model),
and estimates the speed and deceleration rate of the vehicle by calculating the speed and deceleration rate of each
wheel.
b. Initial Check
An initial check is carried out every time once after the engine has started and the initial vehicle speed exceeds 6 km/h
(4 mph).
c. Self±Diagnosis
If the ABS ECU detects a malfunction in the ABS, the ABS warning light and a master warning lights in the
combination meter will light up and alert the driver that a malfunction has occurred. The ECU will also store the codes
of the malfunctions.
 SUSPENSION
1. General
The shock absorber of the 2JZ±GTE engine model with manual transmission has been changed from the
mono±tube, gas±filled shock absorber to the twin±tube, gas±filled shock absorber, which is the same type that is
used on the 2JZ±GE engine model.
The same rubber±integrated ball bushing that is used on the 2JZ±GTE engine model is used for the upper arm
bushing of the rear suspension of the 2JZ±GE engine model.
The brace rod of the rear subframe has been relocated to realize excellent riding comfort, in addition, this provides
excellent stability, an controllability.

BE0DM-02
BE-2
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
1980 Author
: Date
:
1997 SUPRA (RM502U)
PROBLEM SYMPTOMS TABLE
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
SymptomSuspect AreaSee page
Ignition switch is not set to each position.1. Ignition SwitchBE-13
ºKey unlock warning systemº does not operate.
1. GAUGE Fuse (J/B No.1)
2. Key Unlock Warning Switch
3. Door Courtesy Switch
4. Wire Harness
BE-13
BE-28
USA:
HEADLIGHT AND TAILLIGHT SYSTEM
SymptomSuspect AreaSee page
Headlight does not light. (Taillight is normal)
1. Headlight Bulb
2. HEAD (LH, RH) Fuse (R/B No.2)
3. Headlight Control Relay (R/B No.2)
4. Integration Relay
5. Headlight Dimmer Switch
6. Light Control Switch
7. Wire Harness
BE-17
BE-13
BE-17
BE-17
Headlight does not light. (Taillight does not light up)
1. Headlight Bulb
2. Integration Relay
3. Light Control Switch
4. Wire Harness
BE-13
BE-17
Only one side light does not light.
1. Headlight Bulb
2. HEAD (LH, RH) Fuse (R/B No.2)
3. Wire Harness
ºLo-Beamº does not light.1. Headlight Dimmer Switch
2. Wire HarnessBE-17
ºHi-Beamº does not light.1. Headlight Dimmer Switch
2. Wire HarnessBE-17
ºFlashº does not light.1. Headlight Dimmer Switch
2. Wire HarnessBE-17

BE-4
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
1982 Author
: Date
:
1997 SUPRA (RM502U) Taillight does not light with light control SW in TAIL.
1. Taillight Relay (J/B No.1)
2. Integration Relay
3. Light Control Switch
4. Wire HarnessBE-17
BE-13
BE-17
Taillight does not go out with light control SW in OFF.
1. Taillight Relay (J/B No.1)
2. Integration Relay
3. Light Control switch
4. Wire HarnessBE-17
BE-13
BE-17
Headlight and Taillight do not light with engine running and light
control SW in OFF.
1. GAUGE Fuse (J/B No.1)
2. Generator L Terminal
3. D.R.L. Relay
4. D.R.L. No.2 Relay (R/B No.2)
5. D.R.L. No.3 Relay
6. Parking Brake Switch
7. Wire Harness
BE-17
BE-17
BE-17
BE-43
FOG LIGHT SYSTEM
SymptomSuspect AreaSee page
Fog light does not light with light control SW HEAD.
(Headlight is normal.)
1. FOG Fuse (R/B No.2)
2. HEAD Fuse (R/B No.2)
3. Fog Light Relay (R/B No.2)
4. Fog Light Switch
5. Wire Harness
BE-23
BE-23
Fog light does not light with light control SW HEAD.
(Headlight does not light)1. Headlight and Taillight system
2. Wire HarnessBE-15
Only one light does not light.1. Bulb
2. Wire Harness
TURN SIGNAL HAZARD WARNING SYSTEM
SymptomSuspect AreaSee page
ºHazardº and ºTurnº do not light up.
1. Hazard Warning Switch
2. Turn Signal Flasher
3. Wire HarnessBE-26
BE-26
The flashing frequency is abnormal.
1. Bulb
2. Turn Signal Flasher
3. Wire Harness
BE-26
Hazard warning light does not light up.
(Turn is normal.)1. HAZ-HORN Fuse (R/B No.2)
2. Wire Harness
Hazard warning light does not light up in one direction.1. Hazard Warning Switch
2. Wire HarnessBE-26
Turn signal does not light up.
(Combination meter, wiper and washer do not operate.)
1. TURN Fuse (J/B No.1)
2. Ignition Switch
3. Turn Signal Switch
4. Wire Harness
BE-13
BE-26
Turn signal does not light up.
1. TURN Fuse (J/B No.1)
2. Turn Signal Switch
3. Wire Harness
BE-26
Turn signal does not light up in one direction.1. Turn Signal Switch
2. Wire HarnessBE-26
Only one bulb does not light up.1. Bulb
2. Wire Harness

- BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE-7
1985 Author
: Date
:
1997 SUPRA (RM502U)
WARNING LIGHTS:
SymptomSuspect AreaSee page
Warning lights do not light up.
(Except Discharge and Door Open)
1. Bulb
2. IGN Fuse (J/B No.1)
3. Ignition Switch
4. Meter Circuit
5. Generator
6. Wire Harness
BE-13
BE-40
Brake Warning Light does not light up.
1. Bulb
2. Brake Fluid Level Warning Switch
3. Parking Brake Switch
4. Bulb Check Relay
5. Meter Circuit
6. Wire Harness
BE-43
BE-43
BE-40
Seat Belt Warning Light does not light up.
1. Bulb
2. Seat Belt Buckle Switch
3. Integration Relay
4. Meter Circuit
5. Wire Harness
BE-43
BE-13
BE-40
Engine Oil Level Warning Light does not light up.
1. Bulb
2. Engine Oil Level Warning Switch
3. Meter Circuit
4. Wire Harness
BE-43
BE-40
Low Oil Pressure Warning Light does not light up.
1. Bulb
2. Low Oil Pressure Warning Switch
3. Meter Circuit
BE-43
BE-40
Door Open Warning Light does not light up.
1. Bulb
2. DOME Fuse (R/B No.2)
3. Door Courtesy Switch
4. Luggage Room Light Switch
5. Integration Relay
6. Meter Circuit
7. Wire Harness
BE-28
BE-28
BE-13
BE-40
Master Warning Light does not light up.
1. Bulb
2. Telltale Light Circuit
3. Meter Circuit
4. Wire Harness
BE-40
BE-40
INDICATOR LIGHTS:
SymptomSuspect AreaSee page
SRS Indicator Light does not light up.
1. Bulb
2. Center Airbag Sensor
3. Wire Harness
DI-555
ABS Indicator Light does not light up.
1. Bulb
2. Traction ECU
3. Wire Harness
DI-499
Malfunction Indicator Light does not light up.
1. Bulb
2. ECM
3. Wire Harness
DI-1
DI-145
TRAC OFF Indicator Light does not light up.
1. Bulb
2. Traction Solenoid Relay
3. Traction ECU
4. Wire Harness
DI-499
DI-499

BE-8
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
1986 Author
: Date
:
1997 SUPRA (RM502U) Security Indicator Light does not light up.
1. Light Emitting Diode
2. Theft Deterrent and Door Lock ECU
3. Wire Harness
DI-608
A/T Shift Position Indicator Light does not light up.
1. Bulb
2. Park/Neutral Position Switch
3. Light Control Rheostat
4. Meter Circuit
5. Wire Harness
DI-354
DI-423
BE-43
BE-40
MANU Indicator Light does not light up.
1. Bulb
2. ECM
3. Meter Circuit
4. Wire Harness
BE-40
O/D OFF Indicator Light does not light up.
1. Bulb
2. O/D Main Switch
3. ECM
4. Meter Circuit
5. Wire Harness
BE-43
DI-1
DI-145
BE-40
TRAC Indicator Light does not light up.
1. Bulb
2. ABS and Traction ECU
3. Meter Circuit
4. Wire Harness
BE-40
Turn Indicator Light does not light up.
1. Bulb
2. Turn Signal and Hazard Warning System
3. Meter Circuit
4. Wire Harness
BE-25
BE-40
High Beam Indicator Light does not light up.
1. Bulb
2. Headlight and Taillight System
3. Meter Circuit
4. Wire Harness
BE-15
BE-40
CRUISE Indicator Light does not light up.
1. Bulb
2. Cruise Control ECU
3. Meter Circuit
4. Wire Harness
DI-660
BE-40
SNOW Indicator Light does not light up.
1. Bulb
2. Traction ECU
3. Meter Circuit
4. Wire Harness
BE-40
ELECTRIC TENSION REDUCER SYSTEM
SymptomSuspect AreaSee page
Tension Reducer does not operate.
(Driver's and Passenger's)1. ECU-IG fuse (J/B No.1)
2. Wire Harness
Tension Reducer does not operate. (Only one side)
1. Buckle Switch
2. Tension Reducer Solenoid
3. Wire HarnessBE-54
BE-43

BE0DO-02
Z18243
Ignition Switch

Key Unlock Warning Switch BE-12
- BODY ELECTRICALIGNITION SWITCH AND KEY UNLOCK WARNING
SWITCH
1990 Author
: Date
:
1997 SUPRA (RM502U)
IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH
LOCATION