Page 111 of 1807
I01390
Condition: Insufficient cooling
I01392
Condition: Insufficient cooling
NOTE : These gauge indica-
tions are shown when the
refrigeration system has
been opened and the refrig-
erant charged without vacu-
um purging.
- AIR CONDITIONINGAIR CONDITIONING SYSTEM
AC-7
2155 Author: Date:
1997 SUPRA (RM502U)
(6) Refrigerant overcharged or insufficient cooling of
condenser
Symptom seen in
refrigeration systemProbable causeDiagnosisRemedy
Pressure too high on both low
and high pressure sides
No air bubbles seen through the
sight glass even when the engine
rpm is lowered Unable to develop sufficient per-
formance due to excessive refrig-
eration system
Insufficient cooling of condenser Excessive refrigerant in
cycle " refrigerant over charged
Condenser cooling " condenser
fins clogged of condenser fan
faulty
(1) Clean condenser
(2) Check condenser fan motor
operation
(3) If (1) and (2) are in normal
state, check amount of refrigerant
Charge proper amount of refriger-
ant
(7) Air present in refrigeration system
Symptom seen in
refrigeration systemProbable causeDiagnosisRemedy
Pressure too high on both low
and high pressure sides
The low pressure piping hot to
touch
Bubbles seen in sight glass
Air entered in refrigeration system
Air present in refrigeration sys-
tem
Insufficient vacuum purging
(1) Check compressor oil to see if
it is dirty or insufficient
(2) Evacuate air and charge new
refrigerant
Page 152 of 1807
AC0RG-01
N08405
AC-74
- AIR CONDITIONINGPRESSURE SWITCH
2222 Author: Date:
1997 SUPRA (RM502U)
REMOVAL
1. DISCONNECT REFRIGERANT FROM REFRIGERA-
TION SYSTEM
HINT:
At the time of installation, please refer to the following item.
Evacuate air from refrigeration system.
Charge system with refrigerant and inspect for leakage of refrig-
erant.
Specified amount: 700 ± 50 g (24.69 ± 1.76 oz.)
2. REMOVE PRESSURE SWITCH FROM LIQUID TUBE
Disconnect the connector and remove the pressure switch.
Torque: 10 N´m (100 kgf´cm, 7 ft´lbf)
HINT:
Lock the switch mounted on the tube with an open end
wrench, being careful not to deform the tube and remove
the switch.
At the time of installation, please refer to the following
item.
Lubricate a new O-ring with the compressor oil and install
the switch.
Page 163 of 1807
- BODY ELECTRICALBODY ELECTRICAL SYSTEM
BE-7
1985 Author: Date:
1997 SUPRA (RM502U)
WARNING LIGHTS:
SymptomSuspect AreaSee page
Warning lights do not light up.
(Except Discharge and Door Open)
1. Bulb
2. IGN Fuse (J/B No.1)
3. Ignition Switch
4. Meter Circuit
5. Generator
6. Wire Harness
BE-13
BE-40
Brake Warning Light does not light up.
1. Bulb
2. Brake Fluid Level Warning Switch
3. Parking Brake Switch
4. Bulb Check Relay
5. Meter Circuit
6. Wire Harness
BE-43
BE-43
BE-40
Seat Belt Warning Light does not light up.
1. Bulb
2. Seat Belt Buckle Switch
3. Integration Relay
4. Meter Circuit
5. Wire Harness
BE-43
BE-13
BE-40
Engine Oil Level Warning Light does not light up.
1. Bulb
2. Engine Oil Level Warning Switch
3. Meter Circuit
4. Wire Harness
BE-43
BE-40
Low Oil Pressure Warning Light does not light up.
1. Bulb
2. Low Oil Pressure Warning Switch
3. Meter Circuit
BE-43
BE-40
Door Open Warning Light does not light up.
1. Bulb
2. DOME Fuse (R/B No.2)
3. Door Courtesy Switch
4. Luggage Room Light Switch
5. Integration Relay
6. Meter Circuit
7. Wire Harness
BE-28
BE-28
BE-13
BE-40
Master Warning Light does not light up.
1. Bulb
2. Telltale Light Circuit
3. Meter Circuit
4. Wire Harness
BE-40
BE-40
INDICATOR LIGHTS:
SymptomSuspect AreaSee page
SRS Indicator Light does not light up.
1. Bulb
2. Center Airbag Sensor
3. Wire Harness
DI-555
ABS Indicator Light does not light up.
1. Bulb
2. Traction ECU
3. Wire Harness
DI-499
Malfunction Indicator Light does not light up.
1. Bulb
2. ECM
3. Wire Harness
DI-1
DI-145
TRAC OFF Indicator Light does not light up.
1. Bulb
2. Traction Solenoid Relay
3. Traction ECU
4. Wire Harness
DI-499
DI-499
Page 195 of 1807
Z18230
Brake Fluid Level Warning Switch
Parking Brake Switch
Telltale Light LH
Telltale Light RHVehicle Speed Sensor
Light Failure Sensor
DOME Fuse
Combination Meter
Door Courtesy Switches GAUGE Fuse
ECU-B Fuse
IGN Fuse
PANEL Fuse
TAIL Fuse Integration
Fuel Sender Gauge
: Engine Coolant Temperature Sensor
: Engine Oil Level Sensor
: Low Oil Pressure Warning Switch
: Park/Neutral Position Switch
: Vehicle Speed Sensor 2JZ-GE2JZ-GTE
1
5
4
3
2 Relay R/B No.2
J/B No.1
Meter Circuit
1
1
5 4
3
2 1
2
3
4
5
BE0E7-01
- BODY ELECTRICALCOMBINATION METER
BE-39
2017 Author: Date:
1997 SUPRA (RM502U)
COMBINATION METER
LOCATION
Page 198 of 1807
I02082I02081
I02080
I02079
I05022
Security Indicator
TRAC OFF Indicator
Low Oil Pressure Warning
Engine Oil Level Warning
Malfunction Indicator
ABS Indicator
No.
Combination Meter (Terminal B2)
ECM
ECM
Low Oil Pressure Warning Switch
Combination Meter (Terminal B4)
TRAC ECU, Traction Solenoid Relay
Ground
Theft Deterrent and Door Lock ECUWire Harness Side
1
2
3
4
5
6
8
9
10
No.Wire Harness Side
GAUGE Fuse
ECU-B Fuse
IGN Fuse
PANEL Fuse
Vehicle Speed Sensor (Terminal 3)
Ground
DOME Fuse
Light Control Rheostat
Combination Meter (Terminal B1)
Generator Terminal
Door Courtesy Switch
Integration Relay (Terminal 9)
Light Failure Sensor Center Airbag Sensor 1
2
3
4
5
6
8
107
11
12
14
15
16
18GAUGE Fuse
PPS ECU, Cruise Control ECU, ECM OD/TRIP
Meter
Open Door Warning
Seat Belt Warning
SRS Warning 8
6 5
3
4
110
2 9
7
10
5
14
18
12
16
15
114
6
1
8
3
2Air Conditioning Amplifier Telltale Light LH:
Telltale Light RH:
Rear Light Warning
Discharge Warning BE-42
- BODY ELECTRICALCOMBINATION METER
2020 Author: Date:
1997 SUPRA (RM502U)
2. TELLTALE LIGHT:
Page 203 of 1807
N06640
BE0044
Ignition
Switch
BatteryWarning Light
N09645
ON
OFF
N09646
ON
OFF
Z07431
Ignition
Switch
BatteryWarning Light
- BODY ELECTRICALCOMBINATION METER
BE-47
2025 Author: Date:
1997 SUPRA (RM502U)
13. INSPECT LOW OIL PRESSURE SWITCH CONTINUITY
(a) Check that there is continuity between terminal and
ground with the engine stopped.
(b) Check that there is no continuity between terminal and
ground with the engine running.
HINT:
Oil pressure should be over 29 kPa (0.3 kgf/cm
2, 4.3 psi)
If operation is not as specified, replace the switch.
14. INSPECT LOW OIL PRESSURE WARNING LIGHT
(a) Disconnect the connector from the warning switch and
ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON, check that the warning light
lights up.
If the warning light does not light up, test the bulb or inspect wire
harness.
15. INSPECT ENGINE OIL LEVEL WARNING SWITCH
CONTINUITY
(a) Check that there is continuity between terminal with the
switch in each position.
(b) Heat the switch to above 60°C (140°F) in an oil bath.
(c) Check that there is continuity between terminals with the
switch ON (float up).
(d) Check that there is no continuity between terminals with
the switch OFF (float down).
If operation is not as specified, replace the switch.
16. INSPECT ENGINE OIL LEVEL WARNING LIGHT
(a) Disconnect the connector from the switch.
(b) Ground terminal 1 on the wire harness connector.
(c) Turn the ignition switch ON. Check that the warning light
lights up approximately 40 seconds later.
If the warning light does not light up, inspect bulb or wire har-
ness.
Page 273 of 1807
BO0QI-01
N08508
100 mm (3.94 in.)
Hole Here
N08509
Adhesive BO-16
- BODYBACK DOOR
2096 Author: Date:
1997 SUPRA (RM502U)
REPLACEMENT
1. REMOVE ROOF SIDE INNER GARNISH
(See page BO-14)
2. REMOVE DAMPER STAY
NOTICE:
When handling the damper.
Do not disassemble the damper because the cylinder
is filled with pressurized gas.
If the damper is to be replaced, drill a 2.0 - 3.0 mm
(0.079 - 0.118 in.) hole in the area shown in the il-
lustration to completely release the high-pressure
gas before disposing of it.
When drilling, chips may fly out so work carefully.
The gas is colorless, odorless and non-toxic.
When working, handle the damper carefully. Never
score or scratch the exposed part of the piston rod,
and never allow paint or oil to get on it.
Do not turn the piston rod and cylinder with the damp-
er fully extended.
3. INSTALL DAMPER STAY
Apply adhesive to the bolts before tightening.
Part No.08833-00070, THREE BOND 1324 or equiva-
lent.
Torque:
Bolt: 7.8 N´m (80 kgf´cm, 69 in.´lbf)
Nut: 5.9 N´m (60 kgf´cm, 52 in.´lbf)
4. INSTALL ROOF SIDE INNER GARNISH
(See page BO-14)
Page 528 of 1807
CO08J-01
- COOLINGCOOLANT
CO-1
1414 Author: Date:
1997 SUPRA (RM502U)
COOLANT
INSPECTION
1. CHECK ENGINE COOLANT LEVEL AT RADIATOR RESERVOIR
The engine coolant level should be between the ºLOWº and ºFULLº lines, when the engine is cold.
If low, check for leaks and add engine coolant up to the ºFULLº line.
2. CHECK ENGINE COOLANT QUALITY
(a) Remove the radiator cap.
CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator
are still hot, as fluid and steam can be blown out under pressure.
(b) There should not be any excessive deposits of rust or scale around the radiator cap or radiator filler
hole, and the coolant should be free from oil.
If excessively dirty, replace the coolant.
(c) Reinstall the radiator cap.
