1995 LAND ROVER DISCOVERY Workshop Manual

BRAKES
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Brakes
Brake pipe connections to:
- Modulator unit 15.................................................................................
- Brake calipers 15.................................................................................
- Master cylinder 15................................................................................
Jump hoses to calipers 15..............................................................................
Bleed screws 15..............................................................................................
Brake caliper to swivel pin housing 82............................................................
Servo assembly to pedal box 26.....................................................................
Master cylinder to servo 26.............................................................................

BRAKES
1
SERVICE TOOLS BRAKE SERVICE TOOLS
LRT-70-500 Brake piston compressor
18G 672

WHEELS AND TYRES
1
DESCRIPTION AND OPERATION TYPES OF WHEEL RIMS AND TYRES
Description
Dependent on specification, the vehicle is equipped
with alloy or pressed steel wheel rims, both using
tubeless radial ply tyres.
Tyre codes
The writing, codes and numbers moulded into the tyre
wall vary between tyre manufacturers, however most
tyres are marked with the information shown in the
illustrated example.
NOTE: The illustration is an example of the
type of markings moulded into tyres and is
for guidance only. For specific tyre
specifications.
See GENERAL SPECIFICATION
DATA, Information, Wheels and Tyres
1.Type of tyre construction -Radial Ply
2.Load index -104
3.Speed symbol -SorT
4.USA Tyre quality grading -Tread wear 160
Traction A temperature B
5.Tread wear indicators moulded into tread pattern
are located at intervals around the tyre and
marked by a code -E66 103S6
6.Tyres with 'Mud Snow' type tread pattern are
marked -M&S
7.Tyre reinforcing mark -Reinforced
8.USA Load and pressure specification -
900Kg(1984LBS) at 340KA (50PSI) MACS
PRESS
9.Tyre size -205 16 ot 235/70 R16
10.Type of tyre -TUBELESS
11.Country of manufacture -MADE IN GREAT
BRITAIN
12.USA Compliance symbol and identification -
DOT AB7C DOFF 267
13.European type approval identification -E11
01234
14.Tyre construction -SIDE WALL 2 PLIES
RAYON. TREAD 2 RAYON 2 STEEL
15.Manufacturer's brand name/type -TRACTION
PLUS mzx M

WHEELS AND TYRES
1
FAULT DIAGNOSIS TYRE WEAR CHART
FAULT CAUSE REMEDY
Rapid wear at Tyres under-inflated Inflate to correct pressure
shoulders Worn suspension components Replace worn components
i.e. ball joints, panhard
rod bushes,steering damper
Excessive cornering speeds
Rapid wear at
centreTyres over-inflated Inflate to correct pressure
of tread
Wear at one
shoulderTrack out of adjustment Adjust track to correct figure
Bent panhard rod Check and replace worn or damaged
components
Bald spots or tyre Wheel out of balance Balance wheel and tyre
cupping assembly
Excessive radial runout Check runout and replace tyre
if necessary
Shock absorber worn Replace shock
Excessive braking
Tyre scalloped Track out of adjustment Adjust toe to correct figure
Worn suspension components Replace as necessary
Excessive cornering speeds
CAUTION: This diagnosis chart is for general guidance only and does not necessarily include
every cause of abnormal tyre wear.

74WHEELS AND TYRES
2
FAULT DIAGNOSIS FAULT - SYMPTOMS
Vibration through steering wheel
1.Check tyre pressures.
See Repair, Tyre
Pressures
2.Check condition of tyres.See Tyre Wear Chart
3.Check front wheel alignment.See STEERING,
Adjustment, Front Wheel Alignment
4.Check wheel balance.See Repair, Wheel
Balancing
NOTE: In the event that any apparent
vibration is not eliminated at this stage.
See PROPELLER SHAFTS, Fault
diagnosis, Vibration Harshness
NOTE: In the event that any apparent
vibration is not eliminated at this stage, go
to steering Fault Diagnosis, Fault -
Symptom (Steering vibration, road wheel
shimmy/wobble).
See STEERING, Fault diagnosis,
Steering Faults
NOTE: Radial ply tyres have a flexible
sidewall, which produces a sidewall bulge
making the tyre appear under-inflated.
This is a normal condition for radial ply tyres. Do
not attempt to reduce this bulge by over-inflating
the tyre.
1. Correct inflation.
2. Under-inflation.
3. Over-inflation.
4. Tread contact with road.

WHEELS AND TYRES
1
REPAIR GENERAL INFORMATION
WARNING: This is a multi- purpose vehicle
with wheels and tyres designed for both
on and off road usage. Only use wheels
and tyres specified for use on the vehicle.
The vehicle is equipped with tubeless 'S','T' or 'H'
rated radial ply tyres as standard equipment. The
tyres are of European metric size and must not be
confused with the "P" size metric tyres available in
North America.
Vehicle wheel sets, including spare wheel, must be
fitted with the same make and type of tyre to the
correct specification and tread pattern. Under no
circumstances must cross-ply or bias-belted tyres be
used.
For tyre specification and pressures.
See GENERAL
SPECIFICATION DATA, Information, Wheels and
Tyres
Alloy Wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter cast aluminium alloy wheels.The
surface has a paint finish covered with a clear
polyurethane lacquer. Care must be taken when
handling the wheel to avoid scratching or chipping the
finish.
The alloy wheel rim is of the asymmetric hump
type incorporating a safety hump to improve
location of the tyre bead in its seat. If difficulty is
experienced in fitting tyres to this type of rim.
See
Tyre Fitting
WARNING: Do not fit an inner tube to an
alloy wheel.
Steel wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter steel wheels.TYRE INSPECTION
Inspect tyres at weekly intervals to obtain maximum
tyre life and performance and to ensure compliance
with legal requirements. Check for signs of incorrect
inflation and uneven wear, which may indicate a need
for balancing or front wheel alignment.
See Fault
diagnosis, Tyre Wear Chart
if the tyres have
abnormal or uneven wear patterns.
Check tyres at least weekly for cuts, abrasions, bulges
and for objects embedded in the tread. More frequent
inspections are recommended when the vehicle is
regularly used in off road conditions.
To assist tyre inspection, tread wear indicators are
moulded into the bottom of the tread grooves, as
shown in the illustration below.
When the tread has worn to a remaining depth of 1.6
mm the indicators appear at the surface as bars which
connect the tread pattern across the width of the tread
as shown in the illustration below.

74WHEELS AND TYRES
2
REPAIR When the indicators appear in two or more adjacent
grooves, at three locations around the tyre, a new tyre
must be fitted.
NOTE: Do not attempt to interchange
tyres, e.g. from front to rear, as tyre wear
produces characteristic patterns
depending on their position. If tyre position is
changed after wear has occured, the performance
of the tyre will be adversely affected.
NOTE: Territorial vehicle regulations
governing tyre wear MUST be adhered to.
WHEELS INSPECTION
Regularly check the condition of the wheels. Replace
any wheel that is bent, cracked, dented or has
excessive runout.
VALVES INSPECTION
Check condition of inflation valve. Replace any valve
that is worn, cracked, loose, or leaking air.TYRE PRESSURES
Maximum tyre life and performance will be
obtained only if tyres are maintained at the correct
pressures.
Tyre pressures must be checked at least once a
month and at least once a week, preferably daily, if
the vehicle is used off road.
The tyre inflation pressure is calculated to give the
vehicle satisfactory ride and steering characteristics
without compromising tyre tread life. For
recommended tyre pressures in all conditions.
See
GENERAL SPECIFICATION DATA, Information,
Wheels and Tyres
American vehicles - A label attached to the inside
edge of the driver's door also provides tyre pressure
information.
Always check tyre inflation pressures using an
accurate gauge and inflate tyres to the
recommended pressures only.
Check and adjust tyre pressuresONLYwhen the
tyres are cold, vehicle parked for three hours or more,
or driven for less than 3.2 km (2 miles) at speeds
below 64 km/h (40 mph). Do not reduce inflation
pressures if the tyres are hot or the vehicle has been
driven for more than 3.2 km (2 miles) at speeds over
64 km/h (40 mph), as pressures can increase by 0.41
bars (6 p.s.i) over cold inflation pressures.
CheckALLtyre pressures including the spare. Refit
the valve caps as they form a positive seal and keep
dust out of the valve.

WHEELS AND TYRES
3
REPAIR WHEEL BALANCING
CAUTION: It is essential that all wheel
balancing is carried out off the vehicle.
The use of on the vehicle balancing could
cause component damage or personal injury and
MUST NOT be attempted.
NOTE: Before attempting to balance a
wheel and tyre assembly clean all mud and
dirt deposits from both inside and outside
rims and remove existing balance weights.
Remove stones from the tyre tread in order to avoid
operator injury during dynamic balancing and to obtain
the correct balance.
Inspect tyres for damage and correct tyre pressures
and balance according to the equipment
manufacturer's instructions.
Alloy wheels
Clean area of wheel rim and attach adhesive balance
weights in position shown. Cut through rear face of
weight strip to detach required weights.
CAUTION: Use only correct adhesive
balance weights to avoid damage to
aluminium wheel rim. DO NOT attempt to
use a steel wheel weight on an aluminium wheel.
Steel wheels
Clean area of wheel rim and attach balance weights in
position shown.