1995 LAND ROVER DISCOVERY Workshop Manual

Mpi
19
REPAIR CAMSHAFT COVER GASKET
Service repair no - 12.29.40 - Exhaust
Service repair no - 12.29.41 - Inlet
Remove
1.Release 4 screws from spark plug cover.
2.Remove spark plug cover.
Inlet only
3.Release clips and disconnect 2 breather hoses
from camshaft cover.
4.Remove 4 bolts securing support brackets to
manifold and cover.
5.Remove support brackets.
6.Remove 12 bolts from camshaft cover.
Exhaust only
7.Remove 13 bolts from camshaft cover.
Inlet and exhaust
8.Remove camshaft cover assemblies.
9.Remove and discard baffle/gasket plate(s).
Refit
1.Place protective cloth over tappets.
2.Using an M8 x 1,25 mm tap, remove all traces of
sealing compound from camshaft housing bolt
holes.
3.Blow out bolt holes using an airline.
4.Ensure all traces of oil are removed from bolt
holes, remove protective cloth.
5.Clean camshaft cover(s) and mating face of
camshaft housing(s).
6.Position new baffle/gasket plate to camshaft
housing(s).
NOTE: Fit baffle/gasket dry.
7.Fit camshaft cover(s).
Inlet only
8.Position spacers and manifold support brackets.
9.Fit bolts finger tight.
10.Working from the centre outwards, progressively
tighten bolts to torque.
10Nm
11.Tighten support bracket to inlet manifold bolts.
12.Connect breather hoses to camshaft cover.

12ENGINE
20
REPAIR
Exhaust only
13.Fit bolts finger tight.
14.Working from the centre outwards, progressively
tighten bolts to the correct torque.
10Nm
Inlet and exhaust
15.Fit spark plug cover to camshaft cover, tighten
screws.CAMSHAFT DRIVE BELT
Service repair no - 12.65.17
Remove
NOTE: If the timing belt is to be removed
from the camshaft gears only, it is not
necessary to remove the drive belt,
crankshaft pulley or timing belt lower cover.
1.Remove drive belt.
2.Remove 5 bolts securing timing belt top cover.
3.Remove top cover.
4.Remove 5 bolts securing timing belt centre
cover.
5.Remove timing belt centre cover.
6.Rotate crankshaft to align timing marks on
camshaft gears - 90°BTDC.

Mpi
21
REPAIR
CAUTION: Never use the camshaft gears,
gear retaining bolts or timing belt to rotate
crankshaft.
7.Fit tool LRT-12-058 to lock flywheel.
8.Position tool LRT-12-060 to lock camshaft gears.
9.Loosen camshaft belt tensioner pulley bolt.
10.Move tensioner to release timing belt tension.
11.Retighten tensioner pulley bolt.
12.Remove 4 bolts securing crankshaft pulley to
crankshaft timing gear.13.Fit tool LRT-12-059 to crankshaft pulley, fit 2
pulley bolts to retain tool.
14.Restrain crankshaft pulley using tool LRT-12-059
and remove crankshaft pulley bolt.
15.Remove bolts securing tool LRT-12-059, remove
crankshaft pulley.
16.Remove timing belt lower cover.
17.If timing belt is to be refitted, mark direction of
rotation of belt.
18.Remove timing belt.

12ENGINE
22
REPAIR
CAUTION: Ease timing belt off gears using
fingers only. Metal levers may damage the
belt and gears. Do not rotate engine with
timing belt removed and cylinder head fitted.
Timing belts must be stored and handled with
care. Always store a timing belt on its edge with a
bend radius greater than 50 mm. Do not use a
timing belt which has been twisted or bent double
as this can fracture reinforcing fibres. Do not use
an oil contaminated timing belt. Although the belt
has a service life of 96,000 miles, 160,000 km, an
existing belt should only be refitted if it has
completed less than 48,000 miles, 80,000 km.
Refit
NOTE: For torque values.See
Specifications, torque, Torque values
1.Clean timing belt gears and pulleys.
2.Clean crankshaft pulley.
CAUTION: If original belt is to be refitted,
ensure direction of rotation mark is facing
correct way.
3.Fit timing belt to gears, starting at the crankshaft
gear and working in an anti-clockwise direction.
CAUTION: Ensure the belt run between the
crankshaft and exhaust camshaft gear is
kept taut during the fitting procedure.
4.Fit timing belt lower cover, tighten 3 bolts to the
correct torque.
5.Fit crankshaft pulley to crankshaft timing gear.
6.Fit tool LRT-12-059 to crankshaft pulley, fit 2
bolts to retain tool.
7.Fit crankshaft pulley centre bolt, and using tool
LRT-12-059 to restrain pulley, tighten bolt to the
correct torque.
8.Remove tool LRT-12-059
9.Fit bolts securing crankshaft pulley to timing
gear, tighten bolts to the correct torque.
10.Remove tool LRT-12-060.Tension belt
1.Loosen timing belt tensioner pulley bolt.
2.Apply
40Nmanti-clockwise torque to inlet cam
pulley bolt and release.
3.Tighten tensioner pulley bolt to the correct
torque.
4.Remove tool LRT-12-058 from flywheel.
5.Fit timing belt centre cover, tighten 5 bolts to the
correct torque.
6.Fit timing belt upper cover, tighten 5 bolts to the
correct torque.
7.Fit drive belt.

Mpi
23
REPAIR CHECK CAMSHAFT DRIVE BELT
Service repair no - 12.65.17
CAUTION: This check must be carried out
at the service intervals specified and
whenever carrying out any repair which
requires the timing belt to be disturbed. Pay
particular attention for signs of belt splitting at
base of teeth.
1.Remove 5 bolts securing timing belt upper cover
2.Remove upper cover.
3.Using a socket and extension bar on the
crankshaft pulley bolt, rotate engine to allow the
timing belt to be inspected.
CAUTION: Do not use camshaft gears or
retaining bolts to rotate engine.
4.Check timing belt condition, renew any belt that
shows signs of oil contamination, cracking,
fraying or splitting at base of teeth.
CAUTION: Cause of oil contamination, if
present, must be rectified.
5.Clean timing belt upper cover.
6.Position upper cover.
7.Fit upper cover securing bolts.

Mpi
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
ENGINE
Timing belt upper cover bolts 5......................................................................
Timing belt centre cover bolts 5.....................................................................
Timing belt lower cover bolts 5......................................................................
Crankshaft pulley centre bolt 85.....................................................................
Crankshaft pulley to timing gear bolts 10........................................................
Tensioner pulley bolt 30..................................................................................
Spark plugs 27................................................................................................
Timing belt upper backplate bolts 10..............................................................
Camshaft gear bolts 65...................................................................................
Exhaust camshaft rear oil seal cover plate bolts 10........................................
Inlet camshaft rear oil seal cover plate bolts 10..............................................
Crankshaft rear oil seal housing bolts 10........................................................
Engine sump bolts
Stage 1 3...............................................................................................
Stage 2 10..............................................................................................
Bell housing nuts 40........................................................................................
L.H. and R.H. engine mounting nuts 85..........................................................
Exhaust manifold to downpipe nuts 10...........................................................
Exhaust downpipe to silencer box nuts 30......................................................
Air conditioning compressor to engine block bolts 45.....................................
Cylinder head bolts
Stage 1 45..............................................................................................
Stage 2 80..............................................................................................
Stage 3 - Further 90°
Camshaft cover bolts 10.................................................................................
Knock sensor 15.............................................................................................
Ignition coil bracket bolts 25............................................................................
Coolant temperature sensor 15......................................................................
Crankshaft sensor bolts 7..............................................................................
Fuel temperature sensor 7.............................................................................
Intake air temperature sensor 7.....................................................................
Fuel rail to inlet manifold bolts 10...................................................................
Fuel feed hose stiffening bracket bolts 7.......................................................
Throttle housing mounting nuts 7...................................................................
Fuel pressure regulator steady bracket bolts 7..............................................
Oxygen sensor 55...........................................................................................

Mpi
1
SERVICE TOOLS ENGINE
LRT-12-056 Engine lifting bracket
18G 1644
LRT-12-058 Location pin valve timing
18G 1523
LRT-12-059 Crankshaft pulley locking tool
18G 1641
LRT-12-060 Locking tool crankshaft gear
18G 1524

12ENGINE
2
SERVICE TOOLS
LRT-12-061 Protection sleeve crankshaft rear oil
18G 1108 seal
LRT-12-063 Remover camshaft oil seals
18G 1476
LRT-12-064 Replacer pilot camshaft front
18G 1475
LRT-12-069 Replacer crankshaft front oil seal
18G 1509