1995 LAND ROVER DISCOVERY lights

GENERAL SPECIFICATION DATA
15
INFORMATION BULBS
REPLACEMENT BULBS TYPE
Exterior lights
Headlamps 12V 60/55W (Halogen)
Headlamps - France amber 12V 60/55W (Halogen)
Auxiliary driving lamps 12V 55W H3 (Halogen)
Sidelamps 12V 5W bayonet
Tail lamps 12V 5/21W bayonet
Reverse lamps 12V 21W bayonet
Stop lamps 12V 21W bayonet
Direction indicator lamps 12V 21W bayonet
Rear side marker lamps 12V 5W capless
Number plate lamps 12V 5W capless
Interior lights
Instrument panel lamps and warning lamps 12V 1.2W bulb/holder unit
Ignition warning lamp (Instrument panel) 12V 2W capless
Interior roof lamps 12V 10W 'Festoon'
Clock illumination 12V 1.2 capless
Cigar lighter illumination 12V 1.2W capless
Door shut face/puddle lamps 12V 5W capless
Auxiliary switch panel illumination (green) 12V 1.2W capless
Heated rear screen warning lamp (amber) 12V 1.2W capless
Hazard warning lamp 12V 1.2W capless
Automatic graphics illumination 12V 5W capless
Heater/air conditioning graphics illumination 12V 1.2W bulb/holder unit
Differential lock warning lamp 12V 1.2W bulb/holder unit
Column switch illumination 12V 1.2W capless
CAUTION: The fitting of new bulbs with wattages in excess of those specified will result in damage
to vehicle wiring and switches.

ZF
1
FAULT DIAGNOSIS ZF AUTOMATIC GEARBOX
Before referring to fault symptoms, carry out initial
static checks first:
INITIAL STATIC CHECKS
Check start positions 'P' & 'N' only........................................................
Reverse lights 'R' only..................................................................
Gear engagements N-D,N-3,N-2,N-1,N-R..........................................................
Full throttle Engine switched off, check full travel at engine and at.......................................................................
pedal.
Oil level 'N' selected, engine running at normal running............................................................................
temperature.
Pressure test
2000 rev/min 10±0.3 bar, 150±5 lbf/in
2....................................................................
Idle pressure 6.9±0.3 bar, 100±5 lbf/in2at 665 to 735 rev/min. ....................................................................
To fit pressure gauge
Service tools:
See Service tools, Automatic
Gearbox
0 to 20 bar, 0 to 300 lbf/in2Pressure gauge.
Flexible hose adaptor.
1.Site vehicle on a ramp [hoist].
2.From under gearbox, remove socket head plug
(located 10cm from oil pipe) Fit hose adaptor
LST502-1.
3.Fit hose to adaptor.
4.Fit gauge 18G502A to hose and route into
vehicle, ensuring hose is clear of rotating parts
and exhaust pipes.
5.Carry out road test.
See Road Test Procedure
Remove pressure gauge
6.Reverse removal procedure.

70BRAKES
4
DESCRIPTION AND OPERATION System description
The brake system consists of dual hydraulic circuits in
a front - rear split. That is individual circuits to front
and rear axles.
Wheelspeed signals are provided by the fitting of
exciter rings to axles and speed sensors.
An ABS stop light switch is fitted to provide a braking
signal to the ECU as well as operate the stop lights.
Electrical wiring is provided as necessary with system
relays and fuses. Discovery Electrical Troubleshooting
Manual gives the location and wiring circuits of these
components.
Visual warning of system malfunction is provided via a
warning light in the instrument panel.
Hydraulic circuit ABS
Key
A = Primary hydraulic circuit
B = Secondary hydraulic circuit
C = Pressure reducing valve
D = ABS ModulatorABS System operation
During normal braking the feel of the brake pedal on
vehicles equipped with ABS will be the same as that
on non ABS vehicles. During ABS cycling the driver
will experience feedback in the form of a pulsating
brake pedal and solenoid/pump motor noise from the
Modulator.
The system is fully automatic in operation both on and
off road, and will only act when the ECU detects that
ABS cycling is necessary. The ECU continually
monitors the operation of the system.
When starting the ABS system will go through a series
of self checks, including a check of the solenoid
valves/pump motor.
WARNING LIGHT
The warning light will be on during the self check
(1.3-2 secs). If no faults are stored in the memory the
light goes out for 0.5sec,then comes on again. It will
then remain on until the vehicle is driven faster than 7
kph/5mph. This is the only time that the light will be on
without indicating a problem.
Any faults detected by the ECU will cause the warning
light to illuminate indicating that the vehicle may not
have full ABS control.

76CHASSIS AND BODY
14
REPAIR Lock barrel and number plate light housing
Disassemble
NOTE: The lock barrel can only be
removed from its housing when the lock
barrel and number plate light housing is
removed from the door.
20.Remove the bolt securing the lock barrel
mounting bracket to the housing and withdraw
the assembled barrel and bracket.
21.Remove the 'O' ring seal from inside the
housing.
22.Remove the spring clip securing the barrel to the
bracket and withdraw the barrel and stem
assembly from the bracket complete with seal.
23.Remove the 'U' clip securing the stem to the
barrel and detach the seal from the inner face of
the barrel.
24.If the lock barrel and number plate light housing
is being renewed, remove the number plate
lights, harness and the housing mounting
bracket, from the existing housing and fit them to
the new housing.
Reassemble
25.Fit the stem to the barrel and secure with the 'U'
clip.
26.Position a new seal on the inner face of the
barrel, insert the stem and barrel into the
mounting bracket and secure with the spring clip.
27.Place a new 'O' ring seal on the inner face of the
barrel aperture in the housing.
28.Insert the assembled bracket and barrel into its
location in the housing, taking care not to disturb
the seal, and secure with the bolt.Refit
29.Fit the outer handle to the door and secure from
the inside with the two nuts and washers.
30.Fit the lock barrel and number plate light housing
by inserting the number plate light leads through
the aperture in the door panel and locating the
rubber grommet in the aperture. Insert the barrel
stem through the door, locate the housing on the
door panel, ensure that the seal seats correctly,
and secure with the single bolt and washer
through the logo aperture.
31.Connect the number plate light leads to the door
harness.
32.Fit the logo to the aperture in the housing.
33.Fit the fulcrum and connecting rod to the barrel
stem and secure with secure with the 'E' clip.
34.Fit the lock and assembled outer 'Y' lever,
secure the lock with the three screws, locate the
'Y' lever pivot and secure with the pin.
35.Fit the connecting rod from the outer handle
lever to the outer 'Y' lever.
36.Fit the childproof lock actuator and check that it
is functioning.
37.Insert the remote button and rod to the location
in the door.
38.Offer up the assembled inner 'Y' lever and
bracket, attach the barrel connecting rod to the
top clip of the upper leg and the rod from the
lock to the lower clip of the upper leg.
39.Locate the barrel stem in the insert on the
bracket.
40.Secure the bracket with the four screws; fitting
the door pull mounting bracket under the heads
of the top two screws.
41.Attach the remote button and the actuator
connecting rods to the 'Y' lever.
42.Fit the inner release handle and attach the
connecting rod to the lock.
43.Refit the vapour protective sheet, door trim panel
and door pull.

76CHASSIS AND BODY
18
REPAIR HEADLINING
Service repair no - 76.64.01/14
Remove
1.Disconnect battery negative lead.
2.Remove the lower trim panels from the rear
compartment.
See rear compartment lower
trim panels.
3.Remove the alpine light trim casing.See alpine
light trim casing.
4.Remove the front bodyside trim casing.See
front bodyside trim casing.
5.Remove the roof lights from the headlining
pocket and from the headlining.
6.Remove the front grab handles.
7.Remove the sun visors and their retaining clips.
8.Remove the front headlining pocket.9.Remove the finishers from the sun roof
apertures.
10.Release the headlining from the channel above
the rear door and manoeuvre it from the vehicle
through the rear door.
11.If the existing headlining is being replaced, if
fitted, remove the passenger net pockets and fit
them to the new headlining.
Refit
12.Reverse removal procedure.

86ELECTRICAL
2
DESCRIPTION AND OPERATION ANTI-THEFT SYSTEM FUNCTION
Perimetric protection
Using the key in the correct sequence will turn on and
off perimetric protection only. When fully perimetrically
armed, all doors, and bonnet [hood] are protected
against unauthorised access. If the door key is used in
the normal manner the driver will be unaware of the
door key sequence. The time taken to lock or unlock
with the key must be less than 5 seconds. To prevent
unauthorised tampering, the alarm will sound if the
key is held in the unlocked position for longer than 5
seconds when armed. Cranking is disabled when
perimetric protection is armed.
NOTE: When key is turned left or right the
keyswitch input will be activated, in
conjunction with the sill button switch
when links are operated.
Volumetric protection
Using the handset transmitter will turn on and off
volumetric protection. In volumetric mode the vehicle
interior is protected using the ultrasonic sensor. Using
the handset also arms and disarms the vehicle
perimetrically. Cranking is disabled when volumetric
and perimetric protection is armed.
NOTE: If armed volumetrically the vehicle
CANNOT be disarmed using the key.
Alarm horn
When an intrusion is detected the alarm horn will
sound intermittently (Switzerland and Denmark
continuous horn sound) and the hazard lights flash
(where territorial regulations allow) for 30 seconds.
The alarm must be retriggered before alarm horn will
sound again.Vehicle status indication
Vehicle status is indicated by up to three devices: (a)
alarm horn, (b) hazard lights, (c) dash board LED.
When the vehicle arms in either mode the hazard
lights will flash three times and the LED will flash
rapidly for 10 seconds. LED will then flash at a slower
rate while vehicle is armed. When the vehicle disarms,
hazard lights will flash once and LED will extinguish. If
LED remains lit, it indicates that the alarm has been
triggered. Turning on ignition or arming the alarm will
extinguish LED. The LED will give a long pulse flash
to indicate the ultrasonic unit being activated.
Central locking
Central locking is controlled by the alarm ECU and
may be operated by the key, sill button(s) or handset.
The system works on both front doors on four door
vehicles or driver's door on two door vehicles.
NOTE: The central door locking system
will shut down for a short period after
more than 15 consecutive operations.
Inertia switch
An inertia switch is incorporated in the alarm system
ECU. If ignition is on and the vehicle receives an
impact sufficient to activate the inertia switch, the ECU
will signal to unlock central locking actuators and flash
hazard lights. Central locking will remain disabled for
30 seconds. To reset turn ignition off and then on after
the 30 second period has elapsed.
Ultrasonic unit
The unit operates by emitting an air pressure carrier
wave and receiving the wave back. Any disturbance
within the vehicle which disturbs the wave will be
detected, triggering the alarm.
When the volumetric sensor is activated it monitors
movement within the vehicle for 15 seconds before
detecting and responding to intrusions. If the sensor
detects movement within the vehicle it delays arming
until a 15 seconds quiet period has elapsed. If
continuous movement is detected the alarm will not
arm volumetrically.

ELECTRICAL
3
DESCRIPTION AND OPERATION Radio frequency system
The RF system uses four frequencies according to
market. If the coaxial aerial is not fitted system
performance will be impaired. Both ECU and handset
have a colour coded label.
Frequency Colour Territory
ECU/Handset
433.92 MHz Blue/black........................... UK, Ireland........................
224.5 MHz, Yellow/yellow............................ France...................
433.92 MHz Blue/Purple........................... Germany......................
433.92 MHz Blue/blue........................... Europe, not France, Switzerland, Italy, Denmark,..........................
Germany
433.92 MHz White/Blue........................... Switzerland, Denmark.......................
315.0 MHz Green/green............................. Rest of world, Italy, Australia....................
315.0 MHz Orange/Green............................. Gulf, Japan..................
Partially armed mode
If a door, tailgate or bonnet [hood] is left open when
the system is armed, the LED will not light for 10
seconds indicating a mislock condition. Hazard lights
will not flash. If an open door or tailgate is causing the
mislock, the starter motor is disabled. The alarm will
sound if ignition is turned to start position. If an open
bonnet [hood] is causing the mislock the starter motor
is disabled. The alarm will arm the volumetric part of
the system. If the door tailgate or bonnet [hood] is
subsequently closed, after a 5 second delay, the
doors will unlock and immediately lock and the system
will fully arm.
Handset transmitter
The handset LED will give one short flash when
button is pressed momentarily.
If button is held down the LED will light again after 2
seconds for 2 seconds, and extinguish until button is
released and repressed. The handset contains unique
information distinguishing it from other transmitters. It
also contains a set of 'random' rolling codes
programmed into the ECU before leaving the factory.
Each time the handset is pressed a different code is
transmitted to the ECU.
If handset is operated more than four times outside
the vehicle range (6 metres) or power supply is
removed, it will be necessary to re-sychronise handset
and the ECU by pressing the handset three times
within range and within 5 seconds.
NOTE: If both handsets are lost or
damaged when system is armed it will be
necessary to fit a new ECU with two
matching handsets.
Handset batteries
If handset LED flashes continuously when button is
pressed, the batteries need replacing. The hazard
lights will flash one 3 second pulse, instead of three
times upon arming vehicle.
Power up mode
The alarm system always remembers the state it was
left in when power was removed. If the alarm powers
up in an armed state and is subsequently triggered it
will give a warning that it will fully trigger unless
disarmed. This warning consists of short horn pulses
every two seconds for 15 seconds.
New born mode
When the ECU is first produced, it will be in its 'new
born' mode. In this mode it will respond to any remote
of the right frequency. This mode will be cancelled
when the ECU has received ten valid handset signals
without power interruption.
Engine cranking
It is only possible to crank the engine when ignition is
ON and alarm disabled.

ELECTRICAL
11
DESCRIPTION AND OPERATION ANTI-THEFT ALARM BUILT-IN TEST (96 MODELS)
NOTE: The handset should be detached
from the key to allow perimetric testing of
the alarm system. The system will
automatically switch to volumetric testing if the
handset is in close proximity to the starter switch.
The built-in test procedure can be accessed providing
the following conditions exist:
Alarm disarmed.
Ignition off.
Doors unlocked.
Bonnet[hood] closed.
The test mode can be entered by completing the
following instructions within 5 seconds:
1.Open bonnet.
2.Turn starter switch on.
3.Open driver's door (far enough to activate
switch).
4.Turn starter switch off.
5.Turn starter switch on.
If the test mode has been correctly accessed, the
sounder/horn will operate briefly and the anti-theft
alarm indicator and hazard warning lights will flash.
Perimetric tests
The anti-theft alarm indicator light and the hazard
warning lights will flash when:
1.Door switches are activated;
2.The bonnet is opened;
3.Sill switches are activated;
4.Key switches are activated.
NOTE: Operation of key switches can be
verified by turning the key in the relevent
direction so as not to simultaneously
activate the sill switch. If the key switch changes
state, the change should be detected but the sill
switch will not be activated.
Volumetric tests
Press the unlock button or move the handset close to
the starter switch to disable perimetric testing and
enable volumetric testing. If movement is detected
within the vehicle by the ultrasonic sensor it will be
indicated by flashing the anti-theft alarm indicator and
hazard warning lights.
NOTE: Exit anti-theft alarm built-in test by
turning starter switch to the off position.