1995 LAND ROVER DISCOVERY Workshop Manual

ELECTRICAL
3
FAULT DIAGNOSIS 1 2 3 4 SUSPECT
L * * * DISCHARGED BATTERY
* L L * IGN. SWITCH AND/OR
WIRING
* * L * COIL OR AMPLIFIER
* * * H AMPLIFIER GROUND
Key
*Expected Voltage
HVoltage higher than expected
LVoltage lower than expectedTEST 3:
Amplifier Switching
Connect voltmeter between battery positive (+ve)
terminal and H.T. coil negative (-ve) terminal.
Voltmeter should register 0 volts.
Switch ignition 'On', voltmeter should still register 0
volts.
Crank engine, voltmeter reading should increase
when cranking, in which case proceed to Test 5.
If no increase in voltage during cranking proceed to
Test 4.

86ELECTRICAL
4
FAULT DIAGNOSIS TEST 4:
Pick-up Coil Resistance
Remove amplifier.
Connect ohmmeter leads to two pick-up terminals in
body of distributor.
The ohmmeter should register between 2k and 5k
ohm if pick-up is satisfactory. If ohmmeter reading is
correct, check all connections between pick-up and
amplifier, if satisfactory, fit new amplifier. If engine still
does not start carry out Test 5.
Change pick-up if ohmmeter reading is incorrect. If
engine still does not start proceed to Test 5.TEST 5:
Coil H.T. Sparking
Remove existing coil/distributor H.T. lead and fit test
H.T. lead to coil tower. Using suitable insulated pliers,
hold free end about 6mm from engine block and crank
engine. There should be good H.T. sparking.
If weak or no sparking, fit new coil, repeat test.
H.T. sparking good, repeat test with original H.T. lead.
If sparking is good carry out Test 6.
If weak or no sparking, fit new H.T. lead, if engine will
not start carry out Test 6.

ELECTRICAL
5
FAULT DIAGNOSIS TEST 6:
Rotor Arm
Remove distributor cover. Disconnect coil H.T. lead
from cover, using insulated pliers hold about 3mm
above rotor arm electrode and crank the engine.
There should be no H.T. sparking between rotor and
H.T. lead. If satisfactory carry out Test 7.
If H.T. sparking occurs, an earth fault on rotor arm is
indicated. Fit new rotor arm. If engine will not start
carry out Test 7.
TEST 7:
Visual and H.T. Cable Checks
Examine: Should be:
1. Distributor Cover Clean, dry, no tracking marks.....................................................
2. Coil Top Clean, dry, no tracking marks....................................................................
3. H.T. Cable Insulation Must not be cracked, chafed or perished...............................................
4. H.T. Cable Continuity Must not be open circuit..............................................
5. Sparking Plugs Clean, dry, and set to correct gap........................................................
NOTE:
1. Reluctor Must not foul pick-up or leads...................................................................
2. Rotor and Insulation Cover Must not be cracked or show signs of tracking marks.....................................

ELECTRICAL
1
ADJUSTMENT IGNITION TIMING
Service repair no - 86.35.15
Adjust
1.It is essential that following procedures are
adhered to. Inaccurate timing can lead to serious
engine damage and additionally create failure to
comply with emission regulations. If timing is
being checked in vehicle, air conditioning
compressor must be disengaged.
2.On initial engine build, or if distributor has been
disturbed for any reason, ignition timing must be
set statically to 6°B.T.D.C.
NOTE: This approximate setting is made
only to ensure that engine may be started.
CAUTION: On no account must engine be
started before this operation is carried out.Equipment required :-
Calibrated Tachometer
Stroboscopic lamp
3.Couple stroboscopic timing lamp and tachometer
to engine following manufacturer's instructions.
4.Disconnect vacuum hose from distributor.
5.Start engine. With no load, and without
exceeding 3,000 rev/min run engine until normal
operating temperature is reached. (Thermostat
open). Check that engine idles within tolerance
specified in data section.
6.Idle speed for timing purposes must not exceed
800 rev/min.
7.Run engine at idle speed and check timing using
stroboscope light on timing marker and pointer.
WARNING: Keep hands and equipment
away from belt.
8.If timing is not as specified, switch off engine.
Loosen distributor clamp bolt and turn distributor
to advance or retard ignition as necessary.
Tighten clamp bolt, start engine and recheck
timing.
WARNING: Personal injury may result if an
attempt is made to adjust distributor whilst
engine is running.
9.Upon completion, switch off engine and retighten
distributor clamping bolt securely. Recheck
timing, to ensure retightening has not disturbed
distributor position.
10.Refit vacuum hose.
11.Disconnect stroboscopic timing lamp and
tachometer from engine.

ELECTRICAL
1
REPAIR FUSE BOX - INTERIOR
Right Hand Drive shown
The interior fusebox is fitted below the steering column, behind the trim panel. It comprises of three integral units.
'A'Main fusebox,'B'Satellite 2,'C'Satellite 1.
A label in the fusebox cover shows the circuits protected, the fuse rating and their locations. Access is by
releasing the fixing screws and lowering the panel.
'A' Main fusebox
1. Stop lights, direction indicators
2. LH side light
3. Radio/cassette/CD player
4. RH headlight main beam
5. LH headlight main beam
6. Cigar lighter
7. Airbag SRS
8. RH side lights
9. Rear fog guard lights
10. RH headlight dipped beam
11. LH headlight dipped beam
12. Multi-function unit
13. Ignition feed for Multi-function unit
14. Instruments, reversing lights
15. Air conditioning, windows
16. Washers & wipers - front
17. Starter, glow plug
18. Wash/wipe - rear, mirrors, cruise control
'B' Satellite 2
1. Electric windows - front
2. Electric windows - rear
3. Anti-lock braking
4. Central door locking
5. Electric sun roof
6. Trailer lights
'C' Satellite 1
1. Anti-theft alarm
2. Headlight washers
3. Engine management
4. Anti-lock brakes
5. Anti-theft alarm
6. Rear air conditioning, heater
'D' Spare fuses (5 off)

86ELECTRICAL
2
REPAIR FUSE BOX - ENGINE COMPARTMENT
The fusebox is located on the right side of the engine compartment. The circuits protected and their locations are
shown on the inside of the fusebox cover. To change a main circuit fuse prise off protective cover A and remove
retaining screws.
Fuses
1. Heated rear window
2. Sidelights
3. Air conditioning
4. Hazard warning lights, horn
5. ABS valve
6. Fuel pump
7. Fuel injectors
A Main circuit fuses
8. ABS pump
9. Ignition circuits
10. Lighting
11. Window lift, central door locking, rear blower
12. Heater, air conditioning
13. Generator

ELECTRICAL
3
REPAIR BATTERY
Service repair no - 86.15.01
NOTE: Some vehicles are fitted with a
battery backed-up sounder. Disconnecting
the vehicle battery will cause the alarm to
sound unless the following procedure is followed:
1.Turn starter switch 'ON' then 'OFF'.
2.Disconnect battery WITHIN 15 SECONDS (see
WARNING).
If alarm is accidentally activated, ensure sounder is
connected and silence by turning the starter switch to
position II.
Remove
WARNING: During battery removal or
before carrying out any repairs or
maintenance to electrical components
always disconnect battery negative lead first. If
positive lead is disconnected with negative lead in
place, accidental contact of wrench to any
grounded metal part could cause a severe spark,
possibly resulting in personal injury. Upon
installation of battery connect positive lead first.
3.Disconnect both battery leads, negative first.
4.Release four nuts securing battery bracket in
position.
5.Remove bracket.
6.Remove battery.
Refit
7.Reverse removal procedure.
NOTE: Coat battery clamps and terminals
with petroleum jelly before refitting.DISTRIBUTOR-LUCAS 35 DLM8 - V8i
Service parts
1. Cap
2. HT brush and spring
3. Rotor arm
4. Insulation cover
5. Pick-up module and base plate assembly
6. Vacuum unit
7. Amplifier module
8. 'O'-ring oil seal
9. Gasket

86ELECTRICAL
4
REPAIR