1995 LAND ROVER DISCOVERY Workshop Manual

STEERING
11
FAULT DIAGNOSIS STIFF STEERING CHECKLIST
NOTE: Having completed visual checks
and steering assessment and confirmed
that vehicle steering load is incorrect carry
out the following procedure in order shown.
Steering wheel 'torque to turn' loads
1.Raise vehicle so both front wheels free.
2.With engine off, centralise steering wheel, and
remove air bag, if fitted or steering wheel pad.
Using torque wrench on column nut, check
torque required to turn the steering wheel one
turn in each direction.
3.Record readings obtained in each direction.
Compare figures obtained with the specified
figures:
Without ABS
4.40 Nm.
With ABS4.65 Nm.
NOTE: If figures are in excess of those
specified carry out steering box tie bar
reset below. If figures are as specified.
See Visual Check and Basic Adjustments
Steering box tie bar reset
1.Loosen the three tie bar fixings one complete
turn.
2.Drive vehicle carefully a short distance (within
the dealership) applying full lock in both
directions in order to settle steering components.
Drive vehicle over speed bumps and include
harsh braking if possible.
WARNING: Do not drive on public
highway.
3.Near end of 2. ensure vehicle is driven in a
straight line on level ground and halted.
4.Tighten panhard rod mounting arm nut,
110 Nm.
5.Tighten the two fixings tie bar to steering box,81
Nm.
6.Recheck steering wheel torque to turn. If torque
reading is still greater than specified, carry out
steering shaft universal joint lubrication.Lower steering shaft universal joint lubrication
1.Check lower steering shaft is correctly phased.
See Repair, Lower Steering Shaft and
Universal Joints
2.Lubricate universal joints with an anti-seizure
type penetrating spray. Work the joints to ensure
full penetration of the spray by driving vehicle
and steering from lock to lock.
3.If steering stiffness still persists carry out swivel
pin preload setting.
Swivel pin preload setting
The swivel pin preload setting must be checked and
set following the workshop manual procedure.
1.NON ABS vehicles.
See FRONT AXLE AND
FINAL DRIVE, Overhaul, Front Stub Axle,
Constant Velocity Joint and Swivel Pin
Housing Non ABS
Note that a pull load of 1.16 - 1.46 kg is required
after the axle shaft and swivel housing seal have
been removed.
2.ABS vehicles.
See FRONT AXLE AND FINAL
DRIVE, Overhaul, Front Stub Axle, Constant
Velocity Joint and Swivel Pin Housing ABS
Note that a torque to turn of 2.0 - 2.8 Nm is
required after the axle shaft and swivel housing
seal have been removed.
3.If steering stiffness still persists carry out
steering column alignment.

57STEERING
12
FAULT DIAGNOSIS Steering column alignment
1.Place vehicle on level ground. Measure the
angle of lower steering shaft using a Pernumeter
placed on the shaft between the universal joints.
The angle should measure a minimum of 12Ê.
2.If necessary, realign the shaft. Release the five
fixings securing the steering column. Position
column as required. Tighten the fixings evenly,
27 Nm.
3.Loosen the three screws securing lower steering
column shroud to upper shroud ensure lower
shroud is clipped to upper shroud. Reposition
shroud, tighten screws.
4.Recheck steering column angle.
Steering box adjustment
1.Check steering box adjustment.
See
Adjustment, Power Steering Box
Steering damper check
1.Check condition of steering damper
See
Steering Damper
VISUAL CHECK AND BASIC ADJUSTMENTS
NOTE: It is important that the following
instructions are carried out in the
sequence shown and the results recorded.
1.Road springs - check that road springs are
correctly seated and are to correct specification
for vehicle. For spring specification.
See
GENERAL SPECIFICATION DATA,
Information, Road Springs Data
2.Ride height - measure trim height from wheel
centre to wheelarch eyebrow. Record results on
data sheet.
3.Check/top up power steering fluid
See Repair,
Power Steering Fluid Reservoir
4.Check tension and condition of drive belt.See
ENGINE, Repair, Drive Belt
5.Track rod/drag link - check condition of track rod,
drag link and ball joints.
See Repair, Drag Link
and Drag Link Ends
If either component is damaged, check operation
of steering damper and steering box for
smoothness. Replace all damaged or worn
components that impair the operation of the
steering system.
6.Suspension bushes - examine all steering and
suspension bushes for signs of wear and
deterioration. Also check all fixings for torque
relaxation. Tighten to correct torque value.
See
FRONT SUSPENSION, Specifications, torque,
Torque Values
7.Oil leaks - check front and rear axle hubs for
leak and repair as necessary.
8.Brake system - check brake system for leaks,
pipe condition, pad wear/contamination, disc
wear/condition and ABS sensors for correct
fitting.
9.Hub end float - check movement in the hubs by
rocking the wheels.
10.Check front wheel alignment. Vehicles displaying
a tendency to veer more than considered
allowable, it is permissible to set the front track
to parallel.
11.Having completed all the above checks and
adjustments, road test vehicle.
See Road Test
Procedure
Attempting to reproduce the symptoms
established earlier. If symptoms still exist refer to
relevant Diagnostic Chart.

STEERING
13
FAULT DIAGNOSIS STEERING LINKAGE INSPECT
NOTE: When inspecting steering linkages
and ball joints for wear the following items
must be checked.
Steering ball joints
1.Check ball joint rubber boots for security, signs
of cracking or deterioration.
2.Check ball joint assemblies for seizure i.e. no
movement on ball joint and associated
assemblies.
3.Check for excessive wear. This will be evident
as extreme movement on track rod and steering
linkages. Renew parts as necessary.
See
Repair, Track Rod and Linkage See Repair,
Drag Link and Drag Link Ends
Steering linkages
4.Check all linkages for wear, deterioration and
damage. Renew parts as necessary.
See
Repair, Track Rod and Linkage See Repair,
Drag Link and Drag Link Ends

STEERING
1
ADJUSTMENT POWER STEERING BOX
Service repair no - 57.10.13
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is stiff or tight and within
warranty, it must be returned to manufacturer. No
attempt must be made to introduce backlash.
1.Apply park brake, select 'P' in automatic
transmission and chock wheels. Support chassis
front on axle stands.
2.Remove engine undertray.
3.Disconnect drag link from steering drop arm.
4.Check torque to turn.
See Fault diagnosis,
Stiff Steering Checklist
5.Centralise steering box.See Centralise
Steering Box
NOTE: Only check for no backlash when
steering box is in central position.
NOTE: If steering wheel is not straight, it
should be repositioned.
See Repair,
Steering Wheel
The adjustment of the steering box ensures
any preload or end float present on centre is
removed.
6.The adjustment is obtained by rocking the drop
arm about centre whilst an assistant slowly
tightens the steering box adjuster screw.
7.Tighten the locknut when all backlash has been
removed.
8.Repeat the check for backlash. If backlash exists
loosen locknut and repeat adjustment
procedure.
9.Turn steering wheel lock to lock and check no
tightness exists.
10.Ensure front wheels are aligned and in straight
ahead position.
See Front Wheel Alignment
11.Adjust drag link 924 mm between ball joint
centres.
12.Connect drag link. Tighten to
40 Nm.
13.Lower vehicle to ground level and remove
chocks.
14.Road test vehicle.
See Fault diagnosis, Road
Test Procedure
NOTE: If steering wheel is not in straight
ahead position when vehicle is travelling
in a straight line, drag link length is
incorrect and is pushing drop arm away from
central position.
Drag link adjust
15.Right hand drive vehicles - if steering wheel is to
right, drag link is too long. If steering wheel is to
left drag link is too short.
Left hand drive vehicles - if steering wheel is to
right, drag link is too short. If steering wheel is to
left drag link is too long.
16.Adjust drag link until steering wheel points
straight ahead when vehicle is travelling in a
straight line.
CENTRALISE STEERING BOX
1.To centralise the box, insert a suitable peg (hole
size 8.06 mm) into the rear of the drop arm and
into the steering box casing to enable rapid and
accurate setting on centre.

57STEERING
2
ADJUSTMENT STEERING LOCK STOPS
Service repair no - 57.65.03
Check
1.Measure clearance between tyre wall and radius
arm at full lock. This must be 20 mm.
Adjust
2.Loosen stop bolt locknut.
3.Turn stop bolt as required.
4.Tighten locknut.
5.Check clearance between tyre wall and radius
arm on each lock.
NOTE: Alternatively lock stop adjustment
may be carried out using following
procedure.
Check
1.Measure stop bolt protrusion as shown in
RR1697M. This must be 40.5 mm.
Adjust
2.Loosen stop bolt locknut.
3.Turn stop bolt as required.
4.Tighten locknut.
5.Check wheel position at full lock.

STEERING
3
ADJUSTMENT FRONT WHEEL ALIGNMENT
Service repair no - 57.65.01
Checking Toe-out dimensions
NOTE: No Adjustment is provided for
castor, camber or swivel pin inclinations.
1.Set vehicle on level ground with road wheels
positioned straight ahead.
2.Push vehicle back and forwards to settle linkage.
3.Measure toe-out at horizontal centre-line of
wheels.
4.Check tightness of clamp bolt fixings. Tighten to
14 Nm.
Adjust
5.Loosen adjuster sleeve clamp.
6.Rotate adjuster to lengthen or shorten track rod.
7.Check toe-out setting as instructions 1 to 4.
When toe-out is correct, tap steering linkage ball
joint, in directions of arrows shown, to maximum
of their travel. This ensures full unrestricted
working travel.
8.Tighten clamp bolts to
14 Nm.
POWER STEERING PUMP DRIVE BELT
Service repair no - 57.20.01
Adjust
NOTE: For details of drive belt adjust
procedure
See ENGINE, Repair, Drive
Belt

STEERING
1
REPAIR POWER STEERING FLUID PIPES
Service repair no - 57.15.21
CAUTION: If any joints are disconnected, it
is essential that open pipe and ports are
plugged to prevent ingress of dirt.
The following procedures must be followed when
refitting fluid pipes:
Power steering pump
1.Remove plugs, place clamp on feed hose.
V8i Steering pump illustrated
2.Push hose onto pump.
3.Hold clamp in position, Tighten to
3 Nm.
4.Fit high pressure union into pump.
5.Hold pipe in correct position. Tighten to
20 Nm.
6.Remove plugs and refit pipes to steering box,
leave fingertight.
7.Tighten to torque: 16mm thread
20 Nm.
14mm thread15 Nm.
Power steering reservoir
1.Remove plugs and refit pipes and clamps.
2.Tighten clamps to3 Nm.

57STEERING
2
REPAIR POWER STEERING BOX
Service repair no - 57.10.01
General precautions
1.Whenever any part of system, is removed or
disconnected, utmost cleanliness must be
observed.
2.Disconnected ports and hoses must be plugged
to prevent ingress of dirt. If metal sediment is
found in system, establish cause rectify and
flush system.
3.Do not start engine until reservoir is full as pump
will be damaged.
4.Metric pipe fittings are used with 'O' ring pipe
ends on fittings to steering box.
5.Follow normal 'O' ring replacement procedure
whenever pipes are disconnected.
6.Ensure compatible metric components when
fitting replacement pipes.
CAUTION: Before removing any parts of
steering linkage, it is imperative that road
wheels are positioned straight ahead.
Then steering wheel removed to prevent rotary
coupler being wound up or damaged.
CAUTION: After refitting steering linkage
parts follow correct procedure to ensure
that road wheels, steering box and
steering wheel are correctly positioned relative to
each other when in straight ahead condition. If
steering wheel requires repositioning, ensure that
drive pegs on rotary coupler are correctly
positioned before steering wheel is replaced.
This ensures drive pegs locate in their holes in
rear of steering wheel.
After final alignment connect rotary coupler
multiplug, tighten steering wheel securing nut and
fit air bag - if fitted or steering wheel trim pad.
NOTE: When drag link is disconnected
from steering box, travel available at
steering wheel to each full lock is not
equal.
Remove
1.Site vehicle on level surface.
2.Open bonnet[hood].
3.Remove filler cap from power steering fluid
reservoir.
4.Clean steering box.
5.Disconnect feed and return pipes from steering
box.
6.Plug open pipes and steering box ports to
prevent ingress of dirt.
7.Support chassis front on axle stands. Or raise
vehicle on a hoist.
WARNING: Ensure wheels are chocked,
parking brake is applied, and low range
selected.