1995 LAND ROVER DISCOVERY Workshop Manual

19FUEL SYSTEM
2
ADJUSTMENT LOW AND HIGH IDLE SPEED
Adjust
The high idle speed (cold start idle) is
automatically set by the setting of the low idle
speed and can not be adjusted individually.
1.Check and adjust throttle cable.
2.Start engine and run it until normal operating
temperature is reached.
3.Using a suitable tachometer, check the engine
idle speed.
See ENGINE TUNING DATA,
Information, 300 Tdi Engine
4.If adjustment is necessary, loosen the locknut on
the injector pump.
5.Turn the adjustment screw either clockwise to
increase the engine speed or anti-clockwise to
decrease the speed. Run the engine at an
increased speed for a few seconds then check
the idle speed again.
6.When the correct speed has been achieved,
hold the adjuster screw steady while tightening
the locknut.
NOTE: The low idle speed control is the
only permitted adjustment in service. Any
additional adjustments required must be
entrusted to authorised Bosch agents.CHECK TURBOCHARGER BOOST PRESSURE
For boost pressure.
See ENGINE TUNING DATA,
Information, 300 Tdi Engine
1.Disconnect, from turbocharger, hose to actuator.
Insert into a suitable "T" piece.
2.Connect a short length of suitable hose to
turbocharger and connect other end to "T" piece.
3.Connect a further length of hose to third leg of
the "T" piece and other end to a pressure gauge
capable of reading in excess of 61 cm Hg. The
pressure gauge hose must be capable of
reaching passenger compartment so that gauge
may be observed.
4.To check maximum boost pressure, drive
vehicle normally but in such a manner that full
throttle can be maintained whilst climbing a hill
with engine speed held steady between 2,500
and 3,000 rev/min.

Tdi
1
REPAIR TANK SENDER UNIT
Service repair no - 88.25.32
WARNING: Ensure that the WARNINGS
and FUEL HANDLING PRECAUTIONS
given in Section 01 are adhered to before
carrying out the following operations.
Special tool - LST131
Remove
1.Disconnect battery negative lead.
2.Remove the rear carpet retainer.
3.Ease the carpet from under the lower trim panels
at the rear of the fold down seats.
4.Raise the carpet to expose the sound insulation.
5.Fold back the sound insulation to reveal the
access panel.
6.Remove the securing screws and detach the
access panel from the floor.
7.Disconnect the multi-plug from sender unit.8.Disconnect the fuel pipes from the sender unit.
9.Using special tool LST131 remove the locking
ring and withdraw the sender unit from the fuel
tank.
Refit
10.Fit the sender unit to the fuel tank and secure
with the locking ring. Tighten to
45to50 Nm.
11.Connect the fuel pipes to the sender unit.
12.Connect multi-plug to sender unit.
13.Inspect the access panel seal to ensure that it is
satisfactory for further use, renew as necessary.
14.Fit the access panel to the aperture in the floor
and secure with the screws.
15.Reverse removal procedure. 1 to 5. Refit the
sound insulation and carpet.

19FUEL SYSTEM
2
REPAIR THROTTLE CABLE
Service repair no - 19.20.06
Remove
1.Disconnect battery negative lead.
2.Remove pin and clevis pin securing throttle
cable to throttle lever.
3.Pull ferrule from abutment bracket and withdraw
throttle cable.
4.Release throttle cable from clip on bulkhead.
5.Remove pin and clevis pin securing throttle
cable to throttle lever.
6.Release grommet from bulkhead.
7.Withdraw throttle cable from engine
compartment.
Refit
8.Reverse removal procedure. Use new pins to
secure clevis pins.
9.Adjust throttle cable.
See Adjustment,
Throttle Cable
INTAKE HOSE TURBOCHARGER
Service repair no - 19.42.11
Remove
1.Disconnect battery negative lead.
2.Loosen clip and disconnect intake hose from
turbocharger.
3.Loosen clip and disconnect breather hose from
intake hose.
4.Remove clip and disconnect hose from air
cleaner, discard clip.
5.Remove intake hose
Refit
6.Reverse removal procedure. Use a new clip to
secure intake hose to air cleaner.

Tdi
3
REPAIR TURBOCHARGER OIL FEED PIPE
Service repair no - 19.42.14
Remove
1.Disconnect battery negative lead.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Manifold
and Exhaust System - Tdi
3.Remove banjo bolt securing oil feed pipe to
turbocharger, discard 2 sealing washers.
4.Unscrew union, disconnect oil feed pipe from
cylinder block.
CAUTION: Plug the connections.
5.Move oil feed pipe from behind turbocharger and
remove.
Refit
6.Reverse removal procedure. use new sealing
washers.
7.Tighten banjo bolt to
20 Nm.
8.Check/top-up engine oil level.TURBOCHARGER OIL DRAIN PIPE
Service repair no - 19.42.12
Remove
1.Disconnect battery negative lead.
2.Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Manifold
and Exhaust System - Tdi
3.Unscrew union and disconnect oil drain pipe
from cylinder lock.
4.Remove 2 bolts securing oil drain pipe to
turbocharger.
5.Remove oil drain pipe, remove and discard
gasket.
CAUTION: Plug the connection.
Refit
6.Ensure mating surfaces of oil pipe, turbocharger
and engine block are clean.
7.Reverse removal procedure. Use a new gasket.
8.Tighten oil drain pipe to turbocharger bolts to
25
Nm.
9.Check/top-up engine oil level.

19FUEL SYSTEM
4
REPAIR TURBOCHARGER ACTUATOR
Service repair no - 19.42.31
Remove
1.Remove exhaust manifold and turbocharger.
See MANIFOLD AND EXHAUST SYSTEM,
Repair, Exhaust Manifold - Tdi
2.Remove 2 nuts securing the actuator to the
turbocharger bracket.
3.Release clip and disconnect hose from actuator.
4.Remove and discard clip securing control lever
to wastegate spindle.
5.Remove turbocharger actuator.
Refit
6.Fit the replacement actuator and secure with
nuts.
7.Push the control lever as far as possible towards
the actuator and apply pressure to keep the
lever in this position.
8.Pressurise the actuator to 57 - 62 cm Hg and
hold this pressure.
CAUTION: Use only the threaded end of
the lever to make adjustments. Forcing the
complete lever in or out will change the
calibration with the possibility of damaging engine
boost.
9.Screw the lever in either direction until the eye
on the end will locate easily over the wastegate
spindle and secure with a new clip.
10.Release the pressure and tighten the locknut.
11.Refit exhaust manifold and turbocharger.
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust Manifold - Tdi
TURBOCHARGER AND GASKET
Service repair no - Turbocharger - 19.42.01
Service repair no - Gasket - 19.42.25
Remove
1.Disconnect battery negative lead.
2.Remove air cleaner assembly.
See Air Cleaner
3.Remove exhaust manifold assembly.See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust Manifold - Tdi
4.Remove and discard clip securing control lever
to wastegate spindle.
5.Remove 4 bolts and 2 clamp plates securing
turbocharger to exhaust manifold.
6.Remove turbocharger and discard gaskets.
Refit
7.Clean mating faces of turbocharger and exhaust
manifold.
8.Reverse removal procedure. Use new clip to
secure control lever to wastegate spindle.
Tighten to
45 Nm.
9.Check/top-up engine oil level.

Tdi
5
REPAIR FUEL LIFT PUMP
Service repair no - 19.45.09
Remove
1.Loosen unions securing fuel injection pipes to
injectors and injector pump. Remove injection
pipes.
2.Plug the connections to prevent the ingress of
foreign material.
3.Loosen unions and disconnect fuel supply and
feed hoses from fuel lift pump.
4.Plug the connections to prevent the ingress of
foreign material.
5.Remove 2 bolts securing lift pump to engine
block.
6.Remove fuel lift pump and discard gasket.Refit
7.Clean mating faces of fuel lift pump and engine
block.
8.Using a new gasket, fit fuel pump, ensure correct
location of lever with camshaft. Fit securing
bolts. Tighten to
25 Nm.
9.Connect fuel hoses to pump and secure unions.
Tighten to
33 Nm.
10.Fit injector pipes to injectors and injection pump,
and secure unions. Tighten to
28 Nm.

19FUEL SYSTEM
6
REPAIR FUEL FILTER ELEMENT
Service repair no - 19.25.07
Remove
1.Disconnect battery negative lead.
2.Clean area around filter head.
3.Place a suitable container beneath filter bowl to
collect any spillage.
4.Loosen bleed screw.
5.Loosen drain tap, allow fuel to drain into
container.
6.Unscrew filter element, discard element.
Refit
7.Clean seal and seating in filter head.
8.Lubricate filter element seal with fuel.
9.Position filter element to filter head and hand
tighten.
10.Reconnect battery negative lead.
11.Crank engine until fuel is drawn through the
system and starts.INTERCOOLER
Service repair no - 19.42.15
Remove
1.Disconnect battery negative lead.
2.Release 2 clips securing fan cowl to radiator top
cover.
3.Remove 4 bolts securing radiator top cover,
remove top cover.
4.Remove nut, bolt and washers securing
intercooler side cover bracket to bonnet [hood]
platform.
5.Release bracket from side cover lug, position
bracket and power steering reservoir aside.
6.Position side cover away from intercooler.
7.Loosen 2 clips and disconnect top hose from
intercooler.
8.Loosen 2 clips and disconnect bottom hose from
intercooler.

Tdi
7
REPAIR
9.Move intercooler upwards and clear of fan cowl.
Refit
10.Ensure locatiing lug grommets are fitted and in
good condition.
11.Ensure foam pad is in good condition and
attached to intercooler.
12.Move intercooler into position.
13.Reverse removal procedure.GLOW PLUGS
Service repair no - 19.60.31
Remove
1.Disconnect battery negative lead.
No.1 glow plug - air conditioning models
2.Release drive belt from compressor pulley.See
ENGINE, Repair, Drive Belt Renew
3.Remove 4 bolts securing compressor to front
cover, move compressor aside.
No.3 glow plug
4.Remove bolt securing Hummel valve, withdraw
valve, remove and discard 'O' ring.