1995 LAND ROVER DISCOVERY Workshop Manual

54FRONT AXLE AND FINAL DRIVE
2
DESCRIPTION AND OPERATION
Front axle
1. Axle casing
2. Ventilation pipe
3. Axle shaft
4. Wheel studs and hub
5. Stub axle
6. Wheel bearings (2)
7. Inner and outer hub seals
8. Axle shaft seal
9. Hub lock plate, thrust washer and nuts (2)
10. Brake disc
11. Drive flange
12. Shim washer and circlip
13. Dust cap14. Constant velocity joint/shaft
15. Thrust collar for CV joint
16. Roller bearing
17. Spacer
18. Circlip
19. Bottom swivel taper bearing
20. Top and bottom swivel pins
21. Spherical housing, seal and retainer
22. Swivel housing
23. Constant velocity shaft seal
24. ABS pickup (electrical connection)
25. 'Rialco' bush ABS

FRONT AXLE AND FINAL DRIVE
1
FAULT DIAGNOSIS FAULT DIAGNOSIS
Complaint - Oil leaks
An external leak of lubrication can be caused by a
faulty internal seal. For example, if the seals which
separate the differential from the swivel housings are
faulty and the vehicle is operating or parked on an
embankment, oil may leak across the axle leaving one
swivel with a high level and the other swivel and
differential lacking lubrication.
See 'Description and Operation' for illustrations of oil
seal locations.
When investigating leaks or checking oil levels, it is
essential that all the lubrication is drained from any
housing with a high level and that the other levels are
checked.
Swivel oil should be checked for signs of grease
leaking from the hub bearings and the hub grease
should not contain oil.
Check that the axle ventilation system is clear, as a
blockage can cause internal pressure to force oil past
the seals.
If the vehicle is driven in deep water with defective oil
seals, water may contaminate the lubricants and when
checked, give a false impression that the housing has
been overfilled with oil.
Do not assume that a high oil level is due to over
filling or, that a low level is because of an external
leak.

FRONT AXLE AND FINAL DRIVE
1
REPAIR FRONT AXLE ASSEMBLY
Service repair no - 54.15.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
axle when lowering or repositioning axle.
1.Support chassis front.
2.Remove road wheels.
3.Support axle weight with hydraulic jack.
4.Remove radius arms to chassis frame nuts.
5.Disconnect steering damper from track rod.
Using a extractor remove track rod links from
swivel pin arms.
6.Remove four nuts and bolts securing radius
arms to axle bracket.
7.Remove radius arms.
8.Remove bolts securing brake hose brackets.
Refit bolts to prevent oil leakage.
9.Remove ABS sensor, if applicable.
10.Remove bolts from brake calipers and tie to one
side.
11.Remove nuts and washers securing shock
absorbers to axle.
12.Disconnect drag link from swivel pin housing
arm.
13.Remove two nuts and bolts securing panhard
rod to axle bracket. Lift rod clear of axle.
14.Mark for reassembly drive shaft flanges.
Remove four nuts and bolts, tie propeller shaft to
one side.
15.Lower axle assembly and remove road springs.
16.Disconnect anti-roll[sway] bar link.
See FRONT
SUSPENSION, Repair, Anti-Roll[Sway] Bar
Ball Joint Links
17.Remove axle assembly.
Refit
18.Position axle under vehicle, supporting left side
of axle.
19.Reverse removal procedure.
20.Tighten propeller shaft bolts to
47 Nm.
21.Tighten panhard rod to axle bracket to88 Nm.
22.Tighten drag link to hub arm to40 Nm.
23.Tighten upper swivel pin bolts.See
Specifications, torque, Torque Values
24.Tighten radius arms to axle bolts to197 Nm.
25.Tighten radius arms to chassis side member
nuts to
197 Nm.
26.Tighten track rod end to40 Nm.
Fit new split [cotter] pin.

54FRONT AXLE AND FINAL DRIVE
2
REPAIR FRONT BRAKE DISCS
Service repair no - 70.10.10.
Remove
1.Remove front hub assembly.
See Front Hub
Assembly
2.Remove five hub to disc bolts.
3.Tap disc to separate from hub.
Refit
4.Locate disc to hub.
5.Apply Loctite 270 to disc bolts. Tighten to
73
Nm.
6.Check total disc runout with a dial indicator, this
must not exceed 0,15 mm. If necessary
reposition disc.
7.Fit hub assembly.
See Front Hub Assembly
Disc reclamation
8.Check disc thickness. This dimension may be
reduced to minimum thickness of 12 mm.
Machine equal amount off each face.

FRONT AXLE AND FINAL DRIVE
3
REPAIR FRONT HUB ASSEMBLY
Service repair no - 60.25.01.
Remove
1.Loosen front wheel nuts, jack up vehicle and
lower onto axle stands and remove road wheel.
2.Release brake hose clips and remove brake
caliper. Secure to one side.
3.Lever off dust cap.
4.Remove circlip and drive shaft shim from
driveshaft.
5.Remove five bolts and withdraw driving member
and joint washer.
6.Bend back lock washer tabs.
7.Remove locknut and lock washer.
8.Remove hub adjusting nut.
9.Remove spacing washer.
10.Remove hub and brake disc assembly complete
with bearings.HUB COMPONENTS
1. Dust cap.
2. Drive shaft circlip.
3. Drive shaft shim.
4. Drive member.
5. Drive member joint washer.
6. Drive member retaining bolt.
7. Lock nut.
8. Lock washer.
9. Hub adjusting nut.
10. Spacing washer.
11. Outer bearing.
12. Hub.
13. Inner bearing.
14. Grease seal.
15. Brake disc
16. Disc retaining bolt.

54FRONT AXLE AND FINAL DRIVE
4
REPAIR Refit
11.Clean stub axle and drive shaft and fit hub
assembly to axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
61 Nm.
14.Back off adjusting nut 90°. Tighten to4 Nm.
This will give the required hub end float of
0,010mm
15.Fit a new lock washer.
16.Fit locknut. Tighten to61 Nm.
17.Tab over lock washer to secure adjusting nut
and locknut.
18.Fit a new joint washer to driving member and fit
member to hub and secure with five bolts.
Tighten to
65 Nm.
19.Fit original drive shaft shim and secure with a
circlip.
20.To check drive shaft end play mount a dial
gauge using bracket LRT-99-503 and rest pin in
a loaded condition on end of drive shaft.
21.Fit a suitable bolt to threaded end of drive shaft.
Move drive shaft in and out noting dial gauge
reading. End play should be between0,08 to
0,25 mm.
22.If end play requires adjustment, remove circlip,
measure shim thickness and fit an appropriate
shim to give required end-play.
23.Remove bolt from drive shaft, fit circlip and dust
cap.
24.Fit brake caliper. Tighten to
82 Nm.
25.Bleed brake system.See BRAKES, Repair,
Brake System Bleed
26.Fit road wheel, remove axle stands and tighten
road wheel nuts to
126 Nm.
27.Operate footbrake to locate brake pads before
taking vehicle on road.

FRONT AXLE AND FINAL DRIVE
1
OVERHAUL FRONT DIFFERENTIAL
Service repair no - 54.10.07.
Overhaul
The front and rear differentials are the same. When
overhauling front differential.
See REAR AXLE AND
FINAL DRIVE, Overhaul, Axle Differential
Assembly
FRONT HUB
Service repair no - 60.26.14.
Overhaul
1.Remove front hub assembly.
See Repair,
Front Hub Assembly
2.Remove outer bearing.
3.Mark, for reassembly, relationship between hub
and brake disc, if original hub is to be refitted.
4.Remove five bolts and separate hub from brake
disc.5.Drift out grease seal and inner bearing from hub
and discard seal.
6.Drift out inner and outer bearing tracks.
7.Clean hub and drift in inner and outer bearing
tracks.
8.Pack hub inner bearing with recommended
grease and fit to hub.
HUB COMPONENTS
1. Dust cap.
2. Drive shaft circlip.
3. Drive shaft shim.
4. Drive member.
5. Drive member joint
washer.
6. Drive member
retaining bolt.
7. Lock nut.8. Lock washer.
9. Hub adjusting nut.
10. Spacing washer.
11. Outer bearing.
12. Hub.
13. Inner bearing.
14. Grease seal.
15. Brake disc.
16. Disc retaining bolt.

54FRONT AXLE AND FINAL DRIVE
2
OVERHAUL 9.With lip side leading fit new seal to hub using
special tool LST 137 seal replacer and drift 18G
134. Drive in seal flush with rear face of hub.
Apply grease between seal lips.
10.Fit brake disc to hub, lining up to marks made
during dismantling. apllying Loctite 270, fit five
retaining bolts. Tighten to
73 Nm.
11.Grease and fit outer bearing to hub.
12.Fit front hub assembly.
See Repair, Front Hub
Assembly