1995 LAND ROVER DISCOVERY Workshop Manual

MFI
19
REPAIR THROTTLE CABLE
Service repair no - 19.20.06
Remove
1.Remove clevis pin securing cable to lever.
2.Carefully pry throttle cable adjustment nut out of
mounting bracket.
3.Remove cable from mounting bracket.
4.Release outer cable from retaining clips in
engine compartment.
5.Remove lower dash panel.
6.Disconnect cable from accelerator pedal and
release cable locknut.
7.Feed cable through bulkhead grommet into
engine compartment.
Refit
8.Feed new cable from engine compartment
through bulkhead grommet.
9.Connect cable to accelerator pedal.
10.Connect cable to throttle linkage, using a new
cotter pin.
11.Clip outer cable adjustment nut into mounting
bracket.
12.Adjust outer cable to give 1.57 mm free play in
inner cable. Check throttle operation.

19FUEL SYSTEM
20
REPAIR ACCELERATOR PEDAL
Service repair no - 18.30.35
Remove
1.Remove lower dash panel.
2.Remove clevis pin securing throttle cable to
accelerator pedal.
3.Release tension from pedal return spring.
4.Remove circlip from pedal pivot pin.
5.Withdraw pivot pin.
NOTE: It may be necessary to lower
steering column to gain access to pivot
pin circlip.
6.Remove accelerator pedal.
Refit
7.Lightly grease pivot and clevis pins.
8.Fit clevis pin using aNEWcotter pin.
9.Reverse removal procedure.FUEL PUMP AND SENDER UNIT
Service repair no - 19.45.03
A plastic fuel tank with a combined fuel pump/sender
unit is fitted. The fuel pump/sender unit is accessed
through a panel in the load space floor.
Fuel pump/sender unit
WARNING: Ensure that fuel handling
precautions given in Section 01 -
Introduction are strictly adhered to when
carrying out following instructions.
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Service Tools:
LRT-19-001 wrench - pump retaining ring
LRT-19-002 'Speedfit' disconnector
Remove
1.Depressurise fuel system.
See Depressurising
Fuel System
2.Disconnect battery negative lead.
3.Syphon at least 9 litres (2 gallons) of fuel from
fuel tank into a suitable container that can be
sealed.
4.Remove carpet from loadspace floor and
tailgate.
5.Fold back loadspace sound insulation to reveal
access panel.

MFI
21
REPAIR 6.Remove access panel from floor.
7.Disconnect multi-plug from fuel sender unit.
8.Disconnect two fuel line unions from fuel pump.
9.Using service tool no. LRT-19-001, remove
pump unit retaining ring. Withdraw unit from fuel
tank.
WARNING: A quantity of fuel will be
retained in body of unit, care must be
taken to prevent fuel spillage when unit is
removed.
Refit
10.Insert fuel pump into tank. Fit retaining ring.
Tighten to
48 Nm.
11.Connect fuel lines to pump.
12.Connect multi-plug to sender unit.
13.After assembly, check all fuel pipes, sealing
rings and hose connections are secure.
14.Run engine to check for fuel leaks.
15.Inspect access panel seal, fit a new seal if
necessary.
16.Fit access panel and tighten screws.
17.Reverse removal procedure. 4 - 5. Fit insulation
and carpet.

19FUEL SYSTEM
22
REPAIR FUEL TANK
Service repair no - 19.55.01
WARNING: Ensure that fuel handling
precautions given in Section 01 -
introduction are strictly adhered to when
carrying out following instructions.
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Remove
1.Depressurise fuel system. Disconnect battery
negative lead.
2.Syphon fuel tank into a suitable container that
can be sealed afterwards.
ENSURE TANK IS DRAINED COMPLETELY.
(refer to Warning concerning fuel vapour and
spillage at start of procedure).
3.Remove carpet loadspace floor and tailgate.
4.Fold back sound insulation to reveal access
panel.
5.Remove access panel.
6.Disconnect electrical multi-plug.
7.Disconnect two fuel line unions from fuel pump.
8.Working underneath vehicle mark location of
anti-roll [sway] bar straps.
9.Remove rear anti-roll [sway] bar straps, and
allow bar to swing down clear of tank.
10.Remove tank filler and vent hoses at fuel tank.
11.Remove nut and bolt securing right hand side
fuel tank strap.
12.Disconnect evaporative control pipe at green
end of 'speedfit' connector.
NOTE: To disconnect 'speedfit' connector,
insert forked end of LRT-19-002 into slots
of connector see illustration. Press down
on collet and simultaneously pull pipe from
connector.

MFI
23
REPAIR
13.Remove back two bolts and nut plates securing
fuel tank cradle.
14.Remove front nuts, bolts and washers. Remove
fuel tank cradle.
15.With assistance, tilt right hand side of tank
upwards and manoeuvre tank through chassis to
remove.
Refit
16.Reverse removal procedure. Ensuring sealing
ring, fuel pipe and hose connections are secure.
17.Run engine, check all connections for fuel leaks.

MFI
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Air-Bypass valve (stepper motor) 20...............................................................
All flexible hose securing clamps 1,3...............................................................
Fuel feed pipe - hose to fuel rail 22.................................................................
Fuel filter 31....................................................................................................
EVAPORATIVE LOSS CONTROL SYSTEM
All flexible hose securing clamps 1,7...............................................................
METRIC Nm
M5 6...........................................................................
M6 9...........................................................................
M8 25...........................................................................
M10 45.........................................................................
M12 90.........................................................................
M14 105.........................................................................
M16 180.........................................................................
UNC / UNF
1/4 9...........................................................................
5/16 24.........................................................................
3/8 39...........................................................................
7/16 78.........................................................................
1/2 90...........................................................................
5/8 136...........................................................................
NOTE: Torque values above are for all screws and bolts used except for those specified.

MFI
1
SERVICE TOOLS FUEL SYSTEM
LRT-19-004 Test equipment fuel pressure
18G 500
LRT-19-003 MFI pressure test adaptor
LST 143
LRT-19-002 Connector splitter
LST 144
LRT-19-001 Fuel pump remover
LST 131

SFI
1
DESCRIPTION AND OPERATION ENGINE MANAGEMENT SYSTEM
Description
The engine management system (EMS) maintains
optimum engine performance over the entire
operating range. The correct amount of fuel is
metered into each cylinder inlet tract and the ignition
timing is adjusted at each spark plug.
The system is controlled by the ENGINE CONTROL
MODULE (ECM) which receives data from sensors
located on and around the engine. From this
information it provides the correct fuel requirements
and ignition timing at all engine loads and speeds.
The fuel injection system uses a hot wire Mass Air
Flow Sensor to calculate the amount of air flowing into
the engine.
The ignition system does not use a distributor. It is a
direct ignition system (DIS), using four double ended
coils. The circuit to each coil is completed by
switching inside the ECM.
The on board diagnostic system detects any faults
which may occur within the EMS. Fault diagnosis
includes failure of all EMS sensors and actuators,
emissions related items, fuel supply and exhaust
systems.
The system incorporates certain default strategies to
enable the vehicle to be driven in case of sensor
failure. This may mean that a fault is not detected by
the driver. The fault is indicated by illumination of the
malfunction indicator light (MIL) on North American
specification vehicles.
A further feature of the system is 'robust
immobilisation'.Crankshaft position sensor (CKP Sensor)
The crankshaft position sensor is the most important
sensor on the engine. It is located in the left hand side
of the flywheel housing and uses a different thickness
of spacer for manual and automatic gearboxes. The
signal it produces informs the ECM:
- the engine is turning
- how fast the engine is turning
- which stage the engine is at in the cycle.
As there is no default strategy, failure of the
crankshaft sensor will result in the engine failing to
start. The fault is indicated by illumination of the
malfunction indicator light (MIL) on North American
specification vehicles.
Camshaft position sensor (CMP Sensor)
The camshaft position sensor is located in the engine
front cover. It produces one pulse every two
revolutions. The signal is used in two areas, injector
timing corrections for fully sequential fuelling and
active knock control.
If the camshaft sensor fails, default operation is to
continue normal ignition timing. The fuel injectors will
be actuated sequentially, timing the injection with
respect to top dead centre. Injection will either be
correct or one revolution out of synchronisation. The
fault is not easily detected by the driver. The fault is
indicated by illumination of the malfunction indicator
light (MIL) on North American specification vehicles.
Mass air flow sensor (MAF Sensor)
The 'hot wire' type mass air flow sensor is mounted
rigidly to the air filter and connected by flexible hose to
the plenum chamber inlet. The sensing element of the
MAF Sensor is a hot wire anenometer consisting of
two wires, a sensing wire which is heated and a
compensating wire which is not heated. Air flows
across the wires cooling the heated one, changing its
resistance. The ECM measures this change in
resistance and calculates the amount of air flowing
into the engine.
As there is no default strategy, failure will result in the
engine starting, and dying when it reaches 550
rev/min, when the ECM detects no MAF Sensor
signal. The fault is indicated by illumination of the
malfunction indicator light (MIL) on North American
specification vehicles.