1995 LAND ROVER DISCOVERY airbag

04GENERAL SPECIFICATION DATA
10
INFORMATION COOLING SYSTEM 3.9 V8i
System type Pressurised, spill return, thermostatically controlled.....................................................................
water and anti-freeze mixture. Pump assisted thermo
syphon. Coolant radiator combined with oil cooler.
Fan and viscous coupling assembly 11 blade axial flow 433mm diameter.................................
Pump type Centifugal, impellor, belt driven.........................................................................
Thermostat opening 88 degrees..........................................................
Expansion tank cap pressure 15 p.s.i. (system pressure)............................................
STEERING
Power steering box
Make/type Adwest Varamatic - worm and roller box........................................................................
Ratio Variable: straight ahead 19.3:1 on lock 14.3:1.................................................................................
Steering wheel turns, lock-to-lock 3.375....................................
Steering pump
Make/type -V8i ZF - Unicorn.................................................................
Make/type - Mpi & Tdi Hobourn-Eaton series 500......................................................
Steering geometry
Steering wheel diameter 405mm..................................................
Steering wheel diameter airbag model 400mm.............................
Toe-out measurement 0 to 2mm toe out......................................................
Toe-out included angle 0Ê to 0Ê 16'.....................................................
Camber angle 0Ê.................................................................. Check with vehicle in static..............
unladen condition, that is, vehicle
with water,
Castor angle 3Ê..................................................................... oil and five gallons of fuel. Rock..............
the vehicle up and down at the
front to allow
Swivel pin inclination static 7Ê............................................... it to take up a position..............

19FUEL SYSTEM
2
REPAIR ENGAGEMENT (ON/OFF) SWITCH
Service repair no - 19.75.30
Switch Replacement
Remove
1.Disconnect battery negative lead.
2.Carefully release auxiliary switch panel from
fascia.
3.Disconnect multiplug from switch.
4.Depress retaining lugs on switch, remove switch
from panel.
Bulb replacement
5.Position switch to facilitate removal of bulb.
6.Rotate bulb holder 90°and withdraw it from
switch.CRUISE CONTROL SWITCH
Service repair no - 19.75.36
Remove
1.Disconnect battery negative lead.
2. Models fitted with airbags:Remove driver's
airbag module.
See SUPPLEMENTARY
RESTRAINT SYSTEM, Repair, Driver's
Airbag Module
3. Models without airbags:Turn steering wheel
through 90°. Remove 2 Torx screws securing
pad to steering wheel and remove steering
wheel pad.
4.Disconnect cruise control switch multiplug from
main harness.

CRUISE CONTROL
3
REPAIR
5.Disconnect 2 Lucars from horn contacts.
6.Remove 2 screws securing cruise control switch
to steering wheel.
7.Remove 3 bolts securing mounting bracket to
steering wheel and remove mounting bracket.
8.Remove cruise control switch from steering
wheel.
Refit
9.Reverse removal procedure. Ensuring wiring
harness is routed correctly.
10. Models fitted with airbags:Refit driver's airbag
module and follow all safety precautions.
See
SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, Driver's Airbag Module
ROTARY COUPLER
Service repair no - 19.75.54
The rotary coupler is located behind the steering
wheel. Access is gained by removing the steering
wheel and steering column shroud.
NOTE: On vehicles fitted with airbags.See
SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, Rotary Coupler
Remove
1.Disconnect battery negative lead.
2.Remove steering wheel.
See STEERING,
Repair, Steering Wheel
3.Release 2 turnbuckles securing lower dash
closing panel and lower.
4.Remove 3 screws securing lower half of shroud
to steering column.
5.Disconnect rotary coupler multiplug from
steering column harness.

STEERING
3
DESCRIPTION AND OPERATION Steering column components
1. Upper shroud
2. Column harness
3. Cruise control switch (if fitted)
4. Steering wheel and nut
5. Rotary coupler
6. Column switch
7. Shear bolts
8. Switch saddle
9. Upper steering column
10. Universal joint
11. Universal joint bolt
12. Steering column lock assembly13. Lower shroud
14. Column lock/ignition
15. Air bag mounting bracket (if fitted)
16. Air bag module
17. Steering pad (non-airbag)
18. Lower shaft
19. Rubber coupling
20. Compression joint
21. Universal joint
22. Universal joint bolt

STEERING
11
REPAIR Remove
1.Disconnect battery negative lead.
2.Position road wheels straight ahead so steering
wheel can be correctly re-assembled.
3. Airbag fitted:Remove air bag.
See
SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, Driver's Airbag Module
4.Remove trim pad from steering wheel,
disconnect Lucars from horn button.
5.Disconnect rotary coupler multiplug.
6.Loosen but do not remove retaining nut.
7.Release steering wheel from taper, remove
retaining nut and washer.
8.Release harness from retaining clip.
9.Withdraw steering wheel whilst at the same time
feeding harness through wheel hub.
CAUTION: Prevent rotation of rotary
coupler once steering wheel is removed.
Secure in position with adhesive tape.
NOTE:Do not carry out further
dismantling if component is removed for
access only.
Refit
10.Recheck road wheels are positioned straight
ahead.
11.Position steering wheel to column, feed harness
through wheel hub.
12.Remove adhesive tape securing rotary coupler.
13.Locate rotary coupler drive pegs and indicator
switch self-cancel pegs in steering wheel hub,
push wheel fully onto taper.
14.Fit steering wheel nut. Tighten to
50 Nm.
15.Connect rotary coupler multiplug.
16.Non airbag module: Fit horn push assembly,
connect Lucars to horn button, secure harness
in clip.
17.Fit airbag module - if fitted.
See
SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, Driver's Airbag Module
18.Reconnect battery negative lead.

57STEERING
12
REPAIR UPPER STEERING COLUMN
Service repair no - 57.40.01
NOTE: Steering column assembly is not a
serviceable component.
CAUTION: Before removing any parts of
steering linkage, it is imperative that road
wheels are positioned straight ahead. then
steering wheel removed to prevent rotary coupler
being wound up or damaged.
CAUTION: After refitting steering linkage
parts follow correct procedure to ensure
that road wheels, steering box and
steering wheel are correctly positioned relative to
each other when in straight ahead condition. if
steering wheel requires repositioning, ensure that
drive pegs on rotary coupler are correctly
positioned before steering wheel is replaced.
This ensures drive pegs locate in their holes in
rear of steering wheel.
After final alignment, connect rotary coupler
multiplug, tighten steering wheel securing nut and
fit airbag - if fitted or steering wheel trim pad and
horn push assembly.
Remove
1.Remove steering wheel.
See Steering Wheel
CAUTION: Prevent rotation of rotary
coupler once steering wheel is removed.
Secure in position with adhesive tape.
2.Remove driver's access panel.
3.Remove steering column shroud.
See Steering
Column Shroud
4.Remove rotary coupler.See
SUPPLEMENTARY RESTRAINT SYSTEM,
Repair, Rotary Coupler
5.If fitted - remove 4 screws securing knee bolster,
remove knee bolster.
6.Disconnect column switch multiplug.
7.Disconnect ignition switch multiplug from fuse
box.

STEERING
15
REPAIR STEERING COLUMN LOCK ASSEMBLY
Service repair no - 57.40.31
Remove
CAUTION: Before removing any parts of
steering linkage, it is imperative that road
wheels are positioned straight ahead.
Then steering wheel removed to prevent rotary
coupler being wound up or damaged.
CAUTION: After refitting steering linkage
parts follow correct procedure to ensure
that road wheels, steering box and
steering wheel are correctly positioned relative to
each other when in straight ahead condition. If
steering wheel requires repositioning, ensure that
drive pegs on rotary coupler are correctly
positioned before steering wheel is replaced.
This ensures drive pegs locate in their holes in
rear of steering wheel.
After final alignment connect rotary coupler
multiplug, tighten steering wheel securing nut and
fit airbag module - if fitted.
1.Disconnect battery negative lead.
2.Remove steering column shroud.
See Steering
Column Shroud
3.Release turnbuckles, lower driver's access
panel.
4.If fitted, remove 4 screws securing knee pad,
remove bolster.
5.Disconnect ignition switch multiplug from fuse
box.
6.Disconnect ignition switch main feed multiplug.

SUPPLEMENTARY RESTRAINT SYSTEM
1
DESCRIPTION AND OPERATION SYSTEM COMPONENTS
1. Airbag crash sensors (distributed SRS)
2. SRS warning light (airbag)
3. Rotary coupler
4. Driver's airbag module
5. Passenger's airbag module6. Airbag diagnostic socket
7. Airbag diagnostic control unit
8. Airbag harness (distributed SRS)
9. Knee bolsters (where fitted)
10. Airbag harness