1995 LAND ROVER DISCOVERY fuel filter

GENERAL SPECIFICATION DATA
5
INFORMATION FUEL SYSTEM 3.9 V8i
Fuel system type Lucas 14CUX hot wire system electronically controlled..............................................................
Fuel pump-make/type ACX delco high pressure electrical, immersed in the......................................................
fuel tank
Fuel pump delivery pressure 2.4-2.6 bar (34-37 lbf/in
2) ............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
Airflow Sensor
Make and type Lucas 'Hot Wire' 5AM.................................................................
Injectors
Make and type Lucas 8NJ.................................................................
Electronic Control Unit
Make and type Lucas 14CUX.................................................................
Fuel pressure regulator
Make and type Lucas 8RV.................................................................
Fuel temperature sensor
Make and type Lucas 6TT.................................................................
Coolant temperature sensor
Make and type Lucas 3TT.................................................................
Bypass Airvalve (Stepper motor)
Make and type Lucas 2ACM.................................................................
Throttle potentiometer
Make and type Lucas 215SA.................................................................
Lambda sensor - catalyst vehicles
Make and type Lucas 3LS.................................................................

04GENERAL SPECIFICATION DATA
6
INFORMATION FUEL SYSTEM (GEMS) 4.0 V8 ENGINE
Type Sagem - Lucas Gems 8 hot wire system electronically.................................................................................
controlled
Fuel pump-make/type High pressure electrical, immersed in the fuel tank......................................................
Fuel pump delivery pressure 2.4-2.6 bar (34-37 lbf/in
2) ............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
Mass airflow sensor
Make and type Lucas 'Hot Wire' 20AM.................................................................
Injectors
Make and type Lucas D1000.................................................................
Electronic Control Module
Make and type Lucas GEMS 8.3.................................................................
Fuel pressure regulator
Make and type Lucas 8RV.................................................................
Coolant temperature sensor
Make and type Lucas 8TT.................................................................
Bypass Air valve (Stepper motor)
Make and type Lucas 3ACM.................................................................
Throttle position sensor
Make and type Lucas 3TP.................................................................
Heated oxygen sensor - catalyst vehicles
Make and type Lucas 4LS.................................................................
Camshaft position sensor
Make and Land Rover part no. Lucas ERR6170.........................................
Crankshaft position sensor
Make and type Lucas 3VRS, Honeywell ERR6049.................................................................
Knock sensor
Make and type Lucas 2KS.................................................................
Intake air temperature sensor
Make and type Lucas 10TT.................................................................
Ignition coils
Make and type Lucas 2DIS2.................................................................
Fuel temperature sensor
Make and type Lucas 6TT.................................................................

04GENERAL SPECIFICATION DATA
20
INFORMATION Lubrication
System Wet sump, pressure fed.............................................................................
Pressure, engine warm at normal operating speeds 25 - 55lbf/in
2= 1,76 - 3,87Kgf cm2........
Oil pump:
- Type G-rotor integral with front cover.......................................................................
- Drive off crankshaft nose.....................................................................
Oil pressure relief valve Non-adjustable....................................................
Relief valve spring:
- Full length 51,6mm......................................................................
- Compressed length at 7.71Kg load 31mm................................
Oil filter Screw-on disposable canister.............................................................................
Engine oil cooler Combined with coolant radiator and intercooler...............................................................
FUEL SYSTEM - 300 Tdi
Fuel lift pump type Mechanical with hand primer............................................................
Fuel lift pump pressure 42 - 55 kpa at 1800 rpm.....................................................
Fuel filter Paper element in disposable canister..........................................................................
Air cleaner Paper element type........................................................................
COOLING SYSTEM - 300 Tdi
System type Pressurised, spill return, thermostatically controlled.....................................................................
water and anti freeze mixture. Pump assisted thermo
syphon. Coolant radiator combined with oil cooler and
turbo intercooler.
Cooling fan 11 blade axial flow 433 mm diameter. 1.29:1 drive.......................................................................
ratio. Viscous coupling.
Pump type Centrifugal, impellor, belt driven.........................................................................
Thermostat opening 88° .........................................................
Expansion tank cap pressure 15lbf/in
2= 1,06Kgf cm2(system pressure) ...........................................
CLUTCH - 300 Tdi
Type Valeo diaphragm spring.................................................................................
Centre plate diameter 235 mm.......................................................
Facing material Verto F202 grooved.................................................................
Release bearing Ball journal...............................................................

04GENERAL SPECIFICATION DATA
24
INFORMATION FUEL SYSTEM - Mpi
Electronic fuel injection data
See ENGINE TUNING DATA, Information, Engine............................................
- Mpi - 2.0 Litre
Fuel Pump:
Make/Type A.C. Rochester/Electric immersible.......................................................................
Pump pressure 3.2 bar.................................................................
Delivery at 3 bar pressure & 12V (min) 64 litre/h............................
Regulated pressure range 3.0 ñ 0.2 bar................................................
Fuel pump delivery pressure 2.3 - 2.5 kgf/cm
2............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
COOLING SYSTEM - Mpi
Pressure cap 15lbf/in
2(1.03 bar) (system pressure) ....................................................................
Thermostat 88 ÊC.......................................................................
CLUTCH - Mpi
Type Diaphragm spring, hydraulically operated.................................................................................
Adjustment Self adjusting.......................................................................
Clutch plate diameter 215.13 mm.......................................................
TRANSMISSION - Mpi
Manual gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward 1 reverse all synchromesh.............................................................................
Transfer box
Type LT230T Two speed reduction on main gearbox output. Front....................................................................
and rear drive permanently engaged via a lockable
differential
Overall ratios (final drive): In high transfer In low transfer
Fifth 4.146:1.................................................................................. 9.761:1
Fourth 4.989:1............................................................................... 11.746:1
Third 7.518:1................................................................................. 17.701:1
Second 11.479:1............................................................................. 27.109:1
First 17.884:1.................................................................................. 42.109:1
Reverse 18.463:1............................................................................ 43.472:1

09LUBRICANTS, FLUIDS AND CAPACITIES
4
INFORMATION CAPACITIES
The following capacity figures are approximate and are provided as a guide only.
Capacities (approx.)* Litres Imp.Unit US unit
Engine sump oil
- 300Tdi models 5,8...................................................... 10.20 pt 12.30 pt
- V8i petrol models 3.9 6,1............................................ 10.70 pt 12.90 pt
- Mpi petrol models 4,90.................................................. 8.70 pt 10.40 pt
Extra when refilling after fitting new filter
- 300Tdi models 0,85...................................................... 1.50 pt 1.80 pt
- V8i petrol models 0,56.................................................. 1.00 pt 1.20 pt
- Mpi 0,4........................................................................ 0.70 pt 0.85 pt
Manual gearbox 2,67............................................................... 4.70 pt 5.70 pt
Automatic gearbox 9,1........................................................... 16.00 pt 19.20 pt
Transfer gearbox oil 2,30......................................................... 4.00 pt 4.90 pt
Front differential 1,70............................................................... 3.00 pt 3.60 pt
Rear differential 1,70................................................................ 3.00 pt 3.60 pt
Power steering box and reservoir LHD 2,90............................ 5.00 pt 6.00 pt
Power steering box and reservoir RHD 3,40............................ 6.00 pt 7.20 pt
Swivel pin housing oil (each) 0,35............................................ 0.60 pt 0.75 pt
Fuel tank usable fuel 89,0........................................................ 19.5 gall 23 gall
Cooling system
- 300Tdi models 11,50...................................................... 20.20 pt 24.30 pt
- V8i petrol models 11,30.................................................. 20.00 pt 23.90 pt
- Mpi 10,00........................................................................ 17.60 pt 21.00 pt
Washer bottle 7,0................................................................... 12.30 pt 14.80 pt
NOTE: * All levels must be checked by dipstick or level plugs as applicable. When draining oil
from the ZF automatic gearbox, oil will remain in the torque converter, refill to high level on
dipstick only.

MAINTENANCE
7
MAINTENANCE
CHECK/ADJUST VALVE CLEARANCES. - Tdi
Valve adjustment.See GENERAL SPECIFICATION
DATA, Information, 300 Tdi Engine
RENEW FUEL FILTER ELEMENT - Tdi
Drain off water and sediment
CAUTION: It is essential that any water
and sediment in fuel filter is drained off, as
water in fuel can result in damage to
injection pump.
1.Hold a small receptacle beneath drain cock.
Unscrew the drain cock half a turn.
2.Drain off water and sediment.
3.Tighten the drain cock immediately fuel starts to
flow from drain cock.
NOTE: Any delay in tightening drain cock
when fuel starts to flow could possibly
mean bleeding fuel system.
Renew fuel filter element
1.Clean area around filter, place a container
beneath.
2.Unscrew filter, a quantity of fuel will be released,
and discard filter.
3.Wet seal of new filter with fuel.
4.Screw new filter into position.
5.Ensure that drain cock is secure.
RENEW AIR CLEANER ELEMENT V8i CATALYST
Mpi - Tdi - V8i NON CATALYST
To renew air cleaner element - V8i, Mpi,Tdi
See FUEL SYSTEM, Repair, Air Cleaner

MAINTENANCE
17
MAINTENANCE
CHECK/TIGHTEN FRONT AND REAR AXLE
SUSPENSION LINK FIXINGS, CHECK CONDITION
OF MOUNTING RUBBERS
DRAIN FUEL SEDIMENTER - Tdi
Fuel sedimenter
The sedimenter is attached to left-hand side of
chassis frame near fuel tank. It increases the working
life of the fuel filter by removing larger droplets of
water and larger particles of foreign matter from fuel.
Drain off water
1.Loosen drain plug, allow water to run out.
Tighten plug immediately pure diesel fuel starts
to flow.
RENEW FUEL FILTER
WARNING: Ensure that fuel handling
precautions given in Section 01 -
Introduction regarding fuel handling are
strictly adhered to when carrying out following
instructions.
See INTRODUCTION, Information,
Fuel Handling Precautions
WARNING: The spilling of fuel is
unavoidable during this operation. Ensure
that all necessary precautions are taken to
prevent fire and explosion.
1.Depressurise fuel system.
See FUEL SYSTEM,
Repair, Depressurising Fuel System
2.The fuel line filter is located on right hand
chassis side member forward of fuel tank filler
neck. Access to filter is gained through right
hand rear wheel arch.
3.Thoroughly clean area around hose connections
to prevent ingress of foreign matter into fuel
system.
4.Loosen two fuel unions and remove hoses from
filter canister.
5.Release securing bolt and bracket, remove filter
from chassis side member.
6.Fit a new filter observing direction of flow arrow
on canister.
7.Fit inlet and outlet hoses. Tighten to
30 Nm.
8.Refit fuel pump relay.
9.Reconnect battery negative lead.
10.Recode radio.
11.Start engine and inspect hose connections for
fuel leaks.

12ENGINE
4
REPAIR 22.Disconnect feed pipe and spill return pipe from
injector pump.
23.Disconnect both pipes from fuel lift pump.
24.Disconnect servo hose from vacuum pump.
25.Remove three retaining nuts and disconnect
exhaust down pipe.
26.Remove oil cooler pipes from oil filter adaptor.
27.If automatic transmission is fitted, disconnect
feed and return pipes at gearbox oil cooler.
Remove retaining bracket from LH side of
cylinder block and release both oil cooler pipes.
28.Support gearbox.
29.Disconnect ground strap from starter motor.
30.On vehicles with automatic transmission, remove
fixings and detach drive plate housing access
panel and gasket.31.Working through drive plate housing aperture
mark the torque convertor and drive plate to
facilitate reassembly.
32.Remove the four convertor to flexible drive
securing bolts, rotating crankshaft to gain access
to each individual bolt.
33.Fit engine lifting bracket to the two RH rear
cylinder head fixing bolts.
34.Using suitable hoist, fit lifting chains to engine.
35.Remove four bolts, from both sides, securing
front engine mounting brackets to cylinder block.
36.Remove two bolts, from both sides, securing
front engine mounting bracket to bell housing.