1995 LAND ROVER DISCOVERY fuel pressure

GENERAL SPECIFICATION DATA
5
INFORMATION FUEL SYSTEM 3.9 V8i
Fuel system type Lucas 14CUX hot wire system electronically controlled..............................................................
Fuel pump-make/type ACX delco high pressure electrical, immersed in the......................................................
fuel tank
Fuel pump delivery pressure 2.4-2.6 bar (34-37 lbf/in
2) ............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
Airflow Sensor
Make and type Lucas 'Hot Wire' 5AM.................................................................
Injectors
Make and type Lucas 8NJ.................................................................
Electronic Control Unit
Make and type Lucas 14CUX.................................................................
Fuel pressure regulator
Make and type Lucas 8RV.................................................................
Fuel temperature sensor
Make and type Lucas 6TT.................................................................
Coolant temperature sensor
Make and type Lucas 3TT.................................................................
Bypass Airvalve (Stepper motor)
Make and type Lucas 2ACM.................................................................
Throttle potentiometer
Make and type Lucas 215SA.................................................................
Lambda sensor - catalyst vehicles
Make and type Lucas 3LS.................................................................

04GENERAL SPECIFICATION DATA
6
INFORMATION FUEL SYSTEM (GEMS) 4.0 V8 ENGINE
Type Sagem - Lucas Gems 8 hot wire system electronically.................................................................................
controlled
Fuel pump-make/type High pressure electrical, immersed in the fuel tank......................................................
Fuel pump delivery pressure 2.4-2.6 bar (34-37 lbf/in
2) ............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
Mass airflow sensor
Make and type Lucas 'Hot Wire' 20AM.................................................................
Injectors
Make and type Lucas D1000.................................................................
Electronic Control Module
Make and type Lucas GEMS 8.3.................................................................
Fuel pressure regulator
Make and type Lucas 8RV.................................................................
Coolant temperature sensor
Make and type Lucas 8TT.................................................................
Bypass Air valve (Stepper motor)
Make and type Lucas 3ACM.................................................................
Throttle position sensor
Make and type Lucas 3TP.................................................................
Heated oxygen sensor - catalyst vehicles
Make and type Lucas 4LS.................................................................
Camshaft position sensor
Make and Land Rover part no. Lucas ERR6170.........................................
Crankshaft position sensor
Make and type Lucas 3VRS, Honeywell ERR6049.................................................................
Knock sensor
Make and type Lucas 2KS.................................................................
Intake air temperature sensor
Make and type Lucas 10TT.................................................................
Ignition coils
Make and type Lucas 2DIS2.................................................................
Fuel temperature sensor
Make and type Lucas 6TT.................................................................

04GENERAL SPECIFICATION DATA
10
INFORMATION COOLING SYSTEM 3.9 V8i
System type Pressurised, spill return, thermostatically controlled.....................................................................
water and anti-freeze mixture. Pump assisted thermo
syphon. Coolant radiator combined with oil cooler.
Fan and viscous coupling assembly 11 blade axial flow 433mm diameter.................................
Pump type Centifugal, impellor, belt driven.........................................................................
Thermostat opening 88 degrees..........................................................
Expansion tank cap pressure 15 p.s.i. (system pressure)............................................
STEERING
Power steering box
Make/type Adwest Varamatic - worm and roller box........................................................................
Ratio Variable: straight ahead 19.3:1 on lock 14.3:1.................................................................................
Steering wheel turns, lock-to-lock 3.375....................................
Steering pump
Make/type -V8i ZF - Unicorn.................................................................
Make/type - Mpi & Tdi Hobourn-Eaton series 500......................................................
Steering geometry
Steering wheel diameter 405mm..................................................
Steering wheel diameter airbag model 400mm.............................
Toe-out measurement 0 to 2mm toe out......................................................
Toe-out included angle 0Ê to 0Ê 16'.....................................................
Camber angle 0Ê.................................................................. Check with vehicle in static..............
unladen condition, that is, vehicle
with water,
Castor angle 3Ê..................................................................... oil and five gallons of fuel. Rock..............
the vehicle up and down at the
front to allow
Swivel pin inclination static 7Ê............................................... it to take up a position..............

04GENERAL SPECIFICATION DATA
20
INFORMATION Lubrication
System Wet sump, pressure fed.............................................................................
Pressure, engine warm at normal operating speeds 25 - 55lbf/in
2= 1,76 - 3,87Kgf cm2........
Oil pump:
- Type G-rotor integral with front cover.......................................................................
- Drive off crankshaft nose.....................................................................
Oil pressure relief valve Non-adjustable....................................................
Relief valve spring:
- Full length 51,6mm......................................................................
- Compressed length at 7.71Kg load 31mm................................
Oil filter Screw-on disposable canister.............................................................................
Engine oil cooler Combined with coolant radiator and intercooler...............................................................
FUEL SYSTEM - 300 Tdi
Fuel lift pump type Mechanical with hand primer............................................................
Fuel lift pump pressure 42 - 55 kpa at 1800 rpm.....................................................
Fuel filter Paper element in disposable canister..........................................................................
Air cleaner Paper element type........................................................................
COOLING SYSTEM - 300 Tdi
System type Pressurised, spill return, thermostatically controlled.....................................................................
water and anti freeze mixture. Pump assisted thermo
syphon. Coolant radiator combined with oil cooler and
turbo intercooler.
Cooling fan 11 blade axial flow 433 mm diameter. 1.29:1 drive.......................................................................
ratio. Viscous coupling.
Pump type Centrifugal, impellor, belt driven.........................................................................
Thermostat opening 88° .........................................................
Expansion tank cap pressure 15lbf/in
2= 1,06Kgf cm2(system pressure) ...........................................
CLUTCH - 300 Tdi
Type Valeo diaphragm spring.................................................................................
Centre plate diameter 235 mm.......................................................
Facing material Verto F202 grooved.................................................................
Release bearing Ball journal...............................................................

04GENERAL SPECIFICATION DATA
24
INFORMATION FUEL SYSTEM - Mpi
Electronic fuel injection data
See ENGINE TUNING DATA, Information, Engine............................................
- Mpi - 2.0 Litre
Fuel Pump:
Make/Type A.C. Rochester/Electric immersible.......................................................................
Pump pressure 3.2 bar.................................................................
Delivery at 3 bar pressure & 12V (min) 64 litre/h............................
Regulated pressure range 3.0 ñ 0.2 bar................................................
Fuel pump delivery pressure 2.3 - 2.5 kgf/cm
2............................................
Fuel filter Bosch in-line filter 'canister' type..........................................................................
COOLING SYSTEM - Mpi
Pressure cap 15lbf/in
2(1.03 bar) (system pressure) ....................................................................
Thermostat 88 ÊC.......................................................................
CLUTCH - Mpi
Type Diaphragm spring, hydraulically operated.................................................................................
Adjustment Self adjusting.......................................................................
Clutch plate diameter 215.13 mm.......................................................
TRANSMISSION - Mpi
Manual gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward 1 reverse all synchromesh.............................................................................
Transfer box
Type LT230T Two speed reduction on main gearbox output. Front....................................................................
and rear drive permanently engaged via a lockable
differential
Overall ratios (final drive): In high transfer In low transfer
Fifth 4.146:1.................................................................................. 9.761:1
Fourth 4.989:1............................................................................... 11.746:1
Third 7.518:1................................................................................. 17.701:1
Second 11.479:1............................................................................. 27.109:1
First 17.884:1.................................................................................. 42.109:1
Reverse 18.463:1............................................................................ 43.472:1

05ENGINE TUNING DATA
4
INFORMATION 300 Tdi ENGINE
Type2.5 Litre Turbo diesel intercooled .................................................................................
Firing order1-3-4-2 .....................................................................
Injection timing1,54 mm lift at T.D.C. ...............................................................
Injection timing with electronic EGR1,40 mm lift at T.D.C. ............................
Injection timing with EDC0,45 mm lift at T.D.C. ..............................................
Timing marks:
Valve timing - manual Slot for pin in flywheel and TDC mark on front pulley........................................................
Valve timing - automatic Slot for pin in ring gear. Access through rear engine...................................................
plate. TDC mark on front pulley
Injection timing Timing pin (service tool).................................................................
Tappet clearances inlet and exhaust 0,20 mm cold...............................
Valve timing: Inlet Exhaust
- Opens 16°B.T.D.C. ............................................................................ 51°B.B.D.C.
- Closes 42°A.B.D.C. ............................................................................ 13°A.T.D.C.
- Peak 103°A.T.D.C. ............................................................................... 109°B.T.D.C.
- Lift 9,67 mm.................................................................................. 9,97 mm
Maximum governed speeds:
- No load (neutral/full throttle) 4600 + 40 - 120 rev/min...........................................
- Idle speed at running temperature 720±20 rev/min .................................
- Die-down time 4 seconds................................................................
INJECTION PUMP
Make & type - standard Bosch rotary R509 type with boost control and two....................................................
speed mechanical governor with auto advance and
solenoid electrical shut-off. Tamper proof sealing on,
no load governed speed and fuel adjustment screws.
Constant volume delivery valves
Make & type - Electronic EGR Bosch rotary R509/1 type with boost control and two.........................................
speed mechanical governor with auto advance and
solenoid electrical shut-off. Tamper proof sealing on
flight speed and fuel adjustment screws. Constant
volume delivery valves. Throttle position sensor for
EGR control.
Make & type - Electronic diesel control - EDC Bosch rotary R500 type with full electronic control of.................
fuelling and timing. Constant pressure delivery valves.

05ENGINE TUNING DATA
6
INFORMATION ENGINE - Mpi - 2.0 LITRE
Type/Capacity 20 T4/1994 cm
3..................................................................
Firing order 1-3-4-2.......................................................................
Compression ration 10 : 1..........................................................
Idle speed:
Controlled by ECM 875±50 rev/min ...........................................................
Exhaust gas Co content:
- Catalyst 0.5% Max. Not adjustable..................................................................
- Non Catalyst 1,0±25% adjustable using Testbook .........................................................
Ignition
Knock sensor ADU 8229...................................................................
Crankshaft sensor ADU 7340............................................................
Ignition Coils
Type NEC 10049.................................................................................
Primary resistance at 20°C 0.4 to 0.61 ohm..............................................
Consumption - engine idling 0.25 to 0.75 amp.............................................
Spark Plugs
Type/Gap GSP 6662 -0,85 mm.........................................................................
Multipoint Fuel Injection
Type Indirect multipoint injection with engine control module.................................................................................
using speed/density method of air flow measurement.
Fuel pressure regulator MKW 10011....................................................
Fuel pump delivery pressure 2.3 - 2.5 bar............................................
Throttle potentiometer voltage
- Throttle closed 0 - 1 Volt......................................................
- Throttle open 4 - 5 Volts.........................................................
MEMS engine control module MKC 10121..........................................
95 RON minimum -UNLEADEDfuel
CAUTION: Do not use LEADED fuel as it will
damage the catalyst. Serious damage to the
engine may occur if a lower octane number fuel
than that recommended is used.

MAINTENANCE
3
MAINTENANCE VEHICLE EXTERIOR
CHECK/ADJUST HEADLAMP ALIGNMENT
Check/adjust headlamp and auxiliary alignment.
CHECK FRONT WHEEL ALIGNMENT
Use recognised wheel alignment equipment to
perform this check and adjustment.
See STEERING,
Adjustment, Front Wheel Alignment
REMOVE WHEELS, CHECK TYRES
Check tyres (including spare) for compliance with
manufacturers' specification.
Check visually for cuts, lumps, bulges, uneven tread
wear and tread depth. Check road wheels for
damage.
Check/adjust tyre pressures.
CHECK/TIGHTEN TOWING BRACKET FITTINGSINSPECT BRAKE PADS FOR WEAR, CALIPERS
FOR LEAKS AND CONDITION
Check thickness of brake pads, fit new pads if
minimum thickness is less than 3,0mm. Check brake
pads for oil contamination. If new brake pads required.
See BRAKES, Repair, Front Brake Pads
or.See BRAKES, Repair, Rear Brake Pads
WARNING: When renewing brake pads, it
is essential that only genuine components
with correct grade of lining are used.
Always fit new pads as complete axle sets, NEVER
individually or as a single wheel set. Serious
consequences could result from out of balance
braking due to mixing of linings.
Refit road wheels
Fit road wheels in original hub position. Secure in
position with wheel nuts, do not fully tighten wheel
nuts at this stage, lower vehicle and finally tighten
wheel nuts to correct torque.
Alloy wheels:
130 Nm.
Steel wheels:130 Nm.
LUBRICATE ALL HINGES, DOOR CHECK
MECHANISMS, BONNET [HOOD] CATCHES AND
FUEL FILLER FLAP