1995 LAND ROVER DISCOVERY bulb

GENERAL SPECIFICATION DATA
15
INFORMATION BULBS
REPLACEMENT BULBS TYPE
Exterior lights
Headlamps 12V 60/55W (Halogen)
Headlamps - France amber 12V 60/55W (Halogen)
Auxiliary driving lamps 12V 55W H3 (Halogen)
Sidelamps 12V 5W bayonet
Tail lamps 12V 5/21W bayonet
Reverse lamps 12V 21W bayonet
Stop lamps 12V 21W bayonet
Direction indicator lamps 12V 21W bayonet
Rear side marker lamps 12V 5W capless
Number plate lamps 12V 5W capless
Interior lights
Instrument panel lamps and warning lamps 12V 1.2W bulb/holder unit
Ignition warning lamp (Instrument panel) 12V 2W capless
Interior roof lamps 12V 10W 'Festoon'
Clock illumination 12V 1.2 capless
Cigar lighter illumination 12V 1.2W capless
Door shut face/puddle lamps 12V 5W capless
Auxiliary switch panel illumination (green) 12V 1.2W capless
Heated rear screen warning lamp (amber) 12V 1.2W capless
Hazard warning lamp 12V 1.2W capless
Automatic graphics illumination 12V 5W capless
Heater/air conditioning graphics illumination 12V 1.2W bulb/holder unit
Differential lock warning lamp 12V 1.2W bulb/holder unit
Column switch illumination 12V 1.2W capless
CAUTION: The fitting of new bulbs with wattages in excess of those specified will result in damage
to vehicle wiring and switches.

19FUEL SYSTEM
2
REPAIR ENGAGEMENT (ON/OFF) SWITCH
Service repair no - 19.75.30
Switch Replacement
Remove
1.Disconnect battery negative lead.
2.Carefully release auxiliary switch panel from
fascia.
3.Disconnect multiplug from switch.
4.Depress retaining lugs on switch, remove switch
from panel.
Bulb replacement
5.Position switch to facilitate removal of bulb.
6.Rotate bulb holder 90°and withdraw it from
switch.CRUISE CONTROL SWITCH
Service repair no - 19.75.36
Remove
1.Disconnect battery negative lead.
2. Models fitted with airbags:Remove driver's
airbag module.
See SUPPLEMENTARY
RESTRAINT SYSTEM, Repair, Driver's
Airbag Module
3. Models without airbags:Turn steering wheel
through 90°. Remove 2 Torx screws securing
pad to steering wheel and remove steering
wheel pad.
4.Disconnect cruise control switch multiplug from
main harness.

STEERING
13
REPAIR
8.Disconnect ignition switch main feed multiplug.
9.Remove 4 nuts securing upper column to lower
mounting.
10.Remove 2 nuts securing lower mounting steady
bracket, remove bracket.
11.Remove pinch bolt securing upper column to
universal joint.
12.Remove 2 nuts and washes securing upper
column to upper mounting bracket.13.Carefully manoeuvre upper column out of
footwell, recover rubber boot.
NOTE: Do not carry out further
dismantling if upper column is removed
for access only.
14.Loosen but, do not remove screw securing
column switch assembly, withdraw assembly to
gain access to multiplugs.
15.Disconnect column switch multiplugs, remove
column switch assembly.
16.Disconnect ignition switch multiplug.
17.Remove shear bolts securing steering column
lock, remove lock and saddle; discard shear
bolts.
18.Withdraw bulb holder from column lock shroud.
19.Transfer components to new upper column,
connect multiplug.
NOTE: Do not shear column lock bolts at
this stage.

57STEERING
16
REPAIR
7.Remove bulb holder from steering column lock
shroud.
8.Tap head of shear bolts anti-clockwise to release
them.
9.Remove and discard shear bolts.
10.Detach saddle.
11.Remove steering column lock assembly.
Refit
12.Position steering lock saddle on column, locating
spigot in hole provided.
13.Place lower lock assembly into column.
14.Fit but do not fully tighten new shear bolts.
15.Connect multiplugs.
16.Insert bulb holder into steering column lock
shroud.
17.Reconnect battery negative lead.
18.Check steering column lock for correct
operation, tighten shear bolts until heads shear
off.
19.Fit steering column shroud.
See Steering
Column Shroud
20.If fitted - fit knee bolster, fit and tighten screws.
21.Raise driver's access panel, secure turnbuckles.DROP ARM
Service repair no - 57.50.14
Remove
1.Place vehicle on a hoist, or support front axle on
axle stands.
2.Disconnect drag link ball joint from drop arm,
using extractor LRT-57-018.

75SUPPLEMENTARY RESTRAINT SYSTEM
12
REPAIR SRS WARNING LIGHT BULBS
Service repair no - 76.73.74
Remove
1.Remove instrument binnacle.
See
ELECTRICAL, Repair, instrument binnacle.
2.Remove window and face plate from instrument
panel.
3.Remove 3 screws securing ECU to instrument
panel.
4.Release and remove small cover from ECU.
5.Disconnect multiplug from ECU.
6.Remove ECU
7.Remove 4 screws securing tachometer.
8.Remove tachometer.

SUPPLEMENTARY RESTRAINT SYSTEM
13
REPAIR
9.Carefully remove 2 screws securing face plate to
tachometer.
10.Release warning light housing from tachometer
circuit board.
11.Carefully (to avoid damage to tachometer needle
and spindle), tilt and remove warning light
housing.
12.Remove 2 warning light bulbs.Refit
13.Reverse removal procedure.
14.Fit new warning light bulbs.
15.Carefully fit warning light housing, ensuring that
locating pegs engage correctly and that retaining
clips lock housing into position.
16.Ensure that tachometer needle is on the correct
side of its stop.
17.Fit instrument binnacle.
See ELECTRICAL,
Repair, instrument binnacle.

76CHASSIS AND BODY
44
REPAIR
7.Remove centre console switch pack cover.
8.Remove 4 screws securing switch pack to
console.
9.Release switch pack from console and
disconnect 7 multiplugs.
NOTE: If the 'Cold Pack' option is not fitted
there will only be 5 switches in pack.
10.Remove switch pack.
Models fitted with electric front seats
11.Release electric front seat switches from centre
console.
12.Disconnect 2 multiplugs from each switch.
13.Remove switches.All models
14.Release hand brake lever gaiter from centre
console.
15.Remove clip and clevis pin securing cable to
hand brake lever.
16.Remove 4 screws securing centre console to
body.
17.Raise hand brake lever, pull centre console
rearwards to gain access to cigar lighter
multiplug and illumination bulb Lucar.
18.Disconnect cigar lighter multiplug and
illumination bulb Lucar.
19.Remove centre console assembly.

CHASSIS AND BODY
45
REPAIR Refit
20.Position centre console assembly, ensuring
harnesses and connectors are not trapped and
are routed to their correct locations.
21.Connect cigar lighter multiplug and illumination
bulb Lucar.
22.Align centre console to body fixings and fascia.
23.Fit and tighten screws securing centre console to
body.
24.Lubricate hand brake lever to cable clevis pin.
25.Align hand brake cable to lever, fit clevis pin and
secure with clip.
26.Secure hand brake lever gaiter to centre
console.
Models fitted with electric front seats
27.Position electric front seat switches,connect
multiplugs and secure to centre console.
All models
28.Position centre console switch pack and connect
multiplugs to switches.
29.Align switch pack to centre console and secure
with screws.
30.Fit centre console switch pack cover.
31.Fit centre console rubber mat.
32.Fit gear selector lever knob and secure gaiter.
33.Fit transfer gear lever knob and secure gaiter.
34.Reconnect battery earth lead.DRINKS TRAY
Service repair no - 76.46.41
Remove
1.Disconnect battery negative lead.
2.Remove ash tray.
See ash tray - dash panel
central louvre panel.
3.Remove switch pack.See switch pack - dash
panel central louvre panel.
4.Remove 6 screws securing drinks tray to dash
panel central louvre panel.
5.Remove drinks tray.
Refit
6.Position drinks tray to dash panel central louvre
panel and secure with screws.
7.Fit switch pack.
See switch pack - dash panel
central louvre panel.
8.Fit ash tray.See ash tray - dash panel central
louvre panel.
9.Connect battery negative lead.