1990 MITSUBISHI SPYDER service

INTERIOR Headlining
,
00003744
NOTE Metal clip position
Rear roof rail
Removal steps
1. assembly
2. holder
3. Rear roof rail trim
4. Sunroof inner weatherstrip 5. Sunroof switch cover
6. Sunroof switch panel
7. Headlining
Tab
REMOVAL SERVICE POINT
DOME LIGHT ASSEMBLY REMOVAL
Press and pull the tab downward to remove the dome light
assembly.
INSTALLATION SERVICE POINT
SUNROOF INNER WEATHERSTRIP
INSTALLATION
Install the sunroof inner weatherstrip with its adhered joint
located toward the rear of the vehicle and on its c enter line.
Adhered joint
Front of vehicle

INTERIORInside Rear View Mirror 7
ISlit IREMOVAL SERVICE POINT’
REAR VIEW MIRROR REMOVAL
a narrow flat-tip. into
rear view mirror bracket, keep the spring pushed
in and
remove the inside rear view mirror in the direction of the
arrow in the illustration.
NOTE
While the spring is pushed in, the connection betwe en the
spring and the
of the button is released.
Revision .

INTERIOR Front Seat
FRONT SEAT
REMOVAL AND INSTALLATION
1.
Front seat assembly
2. Harness connector
3. Seat anchor cover 4. Front seat assembly
22
removal steps
Gear box
TSB Revision
N O T EAfter temporarily tightening the seat mounting nutsand bolts in every installation location, fully ten them to thespecified torque.
REMOVAL SERVICE POINTS OF FRONT SEAT
ASSEMBLY WHEN THERE IS A MALFUNCTION
IN THE POWER SEAT SLIDE MECHANISM
If the seat will not slide due to a malfunction of the slide
motor or the slide switch and the seat mounting nut s and
b o l t s c o n s e q u e n t l y c a n n o t b e r e m o v e d , slide the seat by
the following procedure.
(1)Remove the bolts which secure the gear box to the left
and right ends of the rails.
(2) Remove the gear shaft from the left side. Pull the gear
box at the right side toward you to disengage the g ear
of the slide rail.
(3) Push the seat with your hand to slide it to a p osition
where the seat mounting nut and bolt can be removed .

Section A-A
III
INTERIOR Front Seat
INSTALLATION SERVICE POINT
SEAT ANCHOR COVER INSTALLATION
the rear tab of the seat anchor cover in the front seat
rear mounting bracket. Then rotate the cover in the direction
of arrow to install the side tabs in the side holes of the bracket.
Side tab
Rear tab
Section B-B
tabs
TSB Revision

INTERIOR Rear Seat
Rear seat hook
Rear seat cushion 0 0 0 0 0 0 4 0
Rear
Hook
hook hole
REMOVAL SERVICE POINT
SEAT CUSHION REMOVAL.
While keeping the rear seat hook pulled, lift up the rear seat
cushion to remove it.
INSTALLATION SERVICE POINTS
SEAT BACK INSTALLATION
Push the rear seat back in the direction indicated in the
illustration; then securely attach the attachment w ire to the
body
hook and install the rear’ seat back.
REAR SEAT CUSHION INSTALLATION
(1) the rear seat cushion attachment wire below the
rear seat back.
(2) Pass the rear inner seat belt through the rear s eat cushion.
(3) Insert the rear seat’ cushion lock plate into the rear seat
hook holes.
TSB Revision

INTERIOR Front Seat Belt,
Belt gui
INSTALLATION SERVICE
FRONT INNER SEAT BELT
Accurately insert the front inner seat belt claws i nto the holes
on the seat adjuster.
FRONT OUTER SEAT BELT INSTALLATION

the to prevent the retractor from rotating in the
hole on the body.
(1) Accurately insert the anchor claws into the holes
on the body.
(2) Accurately insert the belt guide claws into the holes on
the body.
(3) Accurately insert the belt guide 5 claws into t he holes
on quarter trim, lower.
TSB Revision

INTERIOR Front Seat. Belt/Rear Belt,
INSPECTION,
FRONT SEAT BELT BUCKLE SWITCH
CHECK, I’ ,
Switch position
2
ON0
OFF
.
REAR SEAT BELT
,
,
SPECIAL TOOL .
ToolTool number and name
S u p e r s e s s i o nApplication
General service tool Removal of switch, trim etc.
TSB Revision .

INTERIOR Rear Seat ‘Belt
REMOVAL AND INSTALLATION
44
33
4433
Rear outer seat belt removal stepsRear inner seat belt steps
l Quarter trim, side (Refer to l seat cushion (Refer to
1. Rear outer seat belt 2. Rear inner seat belt
INSTALLATION SERVICE POINTS
INNER SEAT BELT INSTALLATION
Install the anchor plate along the bead of the body .
OUTER SEAT BELT INSTALLATION

(1) the to prevent the retractor from rotating in
the hole on the body.
(2) Install the anchor plate along the bead of the body.
TSB Revision