1988 PONTIAC FIERO key
[x] Cancel search: keyPage 1751 of 1825
7H-8 REAR END - F STYLE
window will affect the ability of the gas supports to
hold the lift window open.
1. If the gas support system is not working properly,
get a correct replacement part. Very seldom do
gas supports wear out at the same time.
2. Replace a gas support on one side of the car.
3. If lift window falls down, reinstall on the other
side the support removed in step 2.
4. If lift window falls down, replace the support
installed in step 3 with a new gas support.
COMPARTMENT LIB LOCK CYLINDER
The compartment lid lock cylinder on some
models is located in the rear end panel behind the
license plate. On other models, it is in the center rear
end filler section.
The basic method of cylinder attachment where
the lock cylinder is located behind the license plate is
by means of a lock cylinder retainer. Styles with the
lock cylinder in the rear end filler use rivets to retain
the lock cylinder (Fig. 11).
Removal and lnstallation
1. Open rear compartment lid.
2. To
gain access to lock cylinder retainer, loosen
rear end trim panel.
3. Remove pull-down unit (see procedure).
4. Disconnect connector (4, Fig. 13).
5. On
styles with cylinder behind license plate,
remove lock cylinder retainer by pulling retainer
away from lock cylinder and remove cylinder.
With other design, remove tail lamps and center
filler (Fig. 12). Drill out lock cylinder rivets (part
no. 201 1554) using a 6.3 mm
(1/4") drill bit and
remove lock cylinder.
6. To install, reverse removal procedure. Insure that
that gasket mates properly with outer panel to
form a watertight seal. Check for proper
operation of lock cylinder with key. Then install
retainer or new rivets.
REAR COMPARTMENT PULL-DOWN UNIT
The compartment lid lock is staked to the rear
compartment pull-down unit. Service of the lock is not
recommended. If a lock is to be replaced, the entire
pull-down unit will be required.
Adjust
The pull-down unit can be adjusted for proper
lock striker-to-lock engagement. To adjust pull-down
unit, loosen screws (8, Fig. 14) and adjust pull-down
unit as required and tighten screws.
Remove or Disconnect (Fig. 14)
1. Rear end trim panel
2. Wire connections leading from wire harness (4)
3. Screw (5)
4. Cable from clip (6)
5. Mark location of washers on support
(7)
6. Screws (8)
1. RETAINER - LOCK CYLINDER
2. LOCK CYLINDER
8. GASKET
4. RIVET
6. LOCK CYLINDER
6. GASKET
G93988-7H-F
Fig. 11 - Lid Lock Cylinder lnstallation
1. RETAINING NUT
2. FILLER
3. TAIL LAMP
VIEW A
Fig. 12 - Filler Assembly - Tail Lamp
Install or Connect
Unit must be in closed position prior to installing.
1. Screws (8) (make sure washers are in same
location as marked in step 5 of removal
procedure).
2. Cable
to clip and close clip (6).
3. Screw (5)
4. Wire connectors
leading from wire harness (4)
5. Trim
Page 1812 of 1825
BODY INDEX . F STYLE 1
BODY INDEX
a
ABS and Polypropylene Plastic Test .............. 1 H- 13
Actuator. Power Door Lock
.......................... 5H-20
Adhesive-backed Moldings. Emblems. Name Plates
.................................................... 7FI-1
Adhesive Body Side Molding ............................ 1H-3
Adhesive Service
Kit . Stationary Glass ........... 2H-2
Adjuster
. Manual and Power Seats .......... 9H.12. 15
Alignment Checking
. Underbody .................... 3H-1
Anticorrosion Treatment
................................... 1H-4
Armrest
. Door ................................................. 5H-1
Assembling and Coding
Lock Cylinders ............ 1H-1
B
Body
Lock Pillar Trim Finishing Panel
................. 6H-1
Side Hinge Strap
......................................... 5H-10
I 'entilation ................................... .... ............... 4H-1
bonded
Rearview Mirror Support .................... 2H-5
Bucket Seat. High Performance
...................... 9H- 15
C
............................. Cable . Hood Latch Release 4H-1
Cargo Light
. Rear Compartment .................. 7H- 13
..................................................... Carpet 3H.2,7 H. 13
Center High Mounted Stop Lamp
.................. 7H-16
Child Seat
........................................................... 9H-2
Chip Resistant Plastisol Material
...................... 1H-8
...................................... Coding Lock Cylinders 1
H- 1
Colors for Interior Plastic Parts ...................... 1H-14
............................. Compartment Lift Window 7H-2
Garnish Molding
........................................ 8H-2
Glass
Replacement/Adjustment .................... 7H-5
Release Solenoid
.......................................... 7H-9
.......................................................... Spoiler 7H- 13
.................................................. Trim Panel 7H- 1 1
................................................ Weatherstrip 7H- 1 1
Cwnecting/Locking Rods, Doors .................. 5H- 16 I . itrol Arm Knob . Manual Seat .................. 9H-10
Convertible Top
................................................ 8H-7
Cover Assembly
. Luggage Shade ..................... 6H-4
................................................... Cutting Keys 1H- 1
D
............................ Deflector. Inner Panel Water 5H-6
Defogger
. Rear Window .................................. 2H-6
Diagnosis Chart
................................... Manual Seat Adjusters 9H-8
Power Six-Way Seat Adjuster
....................... 9H-9
Dome Lamps
...................................................... 8H-1
Boor Armrest and Pull Handle
.............................. 5H-1
Bell Crank
.................................................... 5H-20
Hardware Lubrication
................................. 5H- 19
Hinges
............................................................. 5H-7
Inner Panel Water Deflector
......................... 5H-6
Inside Handles and Cover Plate
.................... 5H-1
Inside Remote Handle
................................. 5H-16
Insulator Pads
............................................. 5H-6
Jamb Switch
................................................. 5H-19
Lock
.............................................................. 5H- 19
Lock Knob
..................................................... 5H-2
................................................. Lock Striker 5H- 17
............................................ Outside Handle 5H- 16
Outside Mirror
................................... 5H- 1.5 H. 15
Trim Assemblies
............................................ 5H-2
................................................... Weatherstrip 5H-4
................................................. Wedge Plate 5H-18
....................................... Window Assembly 5H- 10
...................................... Belt Sealing Strips 5H-6
........................................ Filler Assembly 5H- 13
.......................................... Front Up Stop 5H-14
................................ Rear Guide Channel 5H- 15
Regulator/Motor .................................... 5H-11
...................................... Door Side Hinge Strap 5H-8
Emblems.
Name Plates and Moldings .
Rear Compartment ........................................ 7H-I
. ....................................... Emblems Roof Panel 8H-3
. ............................. Exterior Lamps Rear End 7H-15
Exterior Moldings
Doors
............................................................ 5H-20
............................................... Rear Quarters 6H-6
.............................................................. Roof 8W-3
Finishing Panel. Quarter Lower Trim .............. 6H-1
Flexible Exterior Plastic Parts
.......................... 1H-9 .
.................................. E/P or TPO Repair 1H-12
Floor Carpet
................................................... 3H-2
Floor Pan Insulators
............................ .. ........ 3H-1
Folding Rear
Seatback ........................ ... ...... 9H- 19
Formed Headlining
.......................................... 8H-1
........................................................ Front End 4H-1
.......................................................... Front Seat 9H-5
............ Adjuster Assembly. Manual/Power 9H- 1 1
................................................... Adjustment 9H- 10
........................... Assembly. Manual/Power 9H- 1 1
................................................................ Back 9H-7
. ................................ Belt Warning System .... 9H-1
................... High Performance Bucket Seat 9H-
15
............................... Manual Control Knob 9H- 10
................................. Manual Recliner Check 9H-7
........................................ Power Seat Switch 9H- 15
............................................. Reclining Back 9H-6
............................... Seatback Head Restraint 9H-5
.................. Seatback Lock Striker/Bar Stop 9H-15
................................. Shoulder Belt Retractor 9H-2
................................. Six-way Seat Adjuster 9H-12
................................... Torque Specifications 9H-8
Fuel Tank Filler
Door/Pocket ........................ 6H-7
Gas Support
. Compartment Lift
........................................................... Window 7H-7
............................... General Body Construction 3H-1
.......................................... General Information 1H-1
Glass Installation
........................................... Extended Method 2H-4
................................................. Short Method 2H-3
...................................... Glass Scratch Removal 2H- 1