2020 MERCEDES-BENZ SPRINTER service

Information on problems with
your vehicle
If yo u should experience a problem with your
ve hicle, particularly one that you belie vemay
af fect its safe ope ration, weurge youto contact
an au thorized Mercedes-Benz Center immediately
to have the problem diagnosed and rectified.
If th e problem is not resol vedto yo ur satisfaction,
please con tact an au thorized Mercedes-Benz
Center again or write toone of thefo llowing
addresses.
In the USA:
Daimler VANS US A,LLC
Cus tomer Assis tance Center
One Mercedes-Benz Drive
Sandy Springs, GA 30328
In Canada:
Mercedes-Benz Canada, Inc.
Cu stomer Relations Department
98 Vande rhoof Avenue
To ronto, Ontario M4G 4C9 Re
porting saf ety defects
USA onl y:
The following text is published as required of
manufacturers under Title 49, Code of U.S. Fed‐
eral Regulations, Part57 5 pursuant tothe
"National Traf fic and Mo torVe hicle Saf etyAc t of
19 66".
If yo u belie vethat your vehicle has a defect which
could cause a crash or could cause injury or
death, you should immediately inform the
Na tional Highw ayTraf fic Saf etyAd ministration
(NHT SA) in addition tonotifying Daimler VANS
US A,LLC.
If NHT SAreceives similar complaints, it may open
an in vestigation, and if it finds that a saf ety
defect exists in a group of vehicles, it may order a
re call and remedy campaign. Ho wever,NHT SA
cannot become in volved in indi vidual problems
between you, your dealer, or Daimler VANS US A,
LLC.
To contact NHT SA,yo u may call theVe hicle
Saf ety Hotline toll-f ree at 1-888-327-4236
(TT Y:1-800-424-9 153); go tohttps://
www.safercar.gov; or write to:Ad ministrator,
NHT SA, 400 Se venth Street,SW .,Wa shington,
DC 20590, US A. Yo
u can find more information on vehicle saf ety
at: https://www.safercar.gov
Canada onl y:
The following text is published as required of
manufacturers under subsection 18.4 (4) of the
Mo torVe hicle Saf etyRe gulations.
If yo u belie vethat your vehicle has a defect which
could cause a crash or could cause injury or
death, you should immediately inform Transport
Canada in addition tonotifying Mercedes-Benz
Canada Inc.
If Transport Canada received similar complaints,
it may open an in vestigation, and if it finds that a
saf ety defect exists in a group of vehicles, it may
order a recall and remedy campaign. Ho wever,
Tr ansport Canada cannot become in volved in
indi vidual problems between you, your dealer or
Mercedes-Benz Canada Inc.
To contact Transport Canada, you may call the
Defect In vestigations and Recalls Division toll-
free in Canada at 1-800-333-05 10or
81 9-994-3328in the Gatineau-Ot tawa area or
internationall y;you may also go tothefo llowing
we bsites for more information:
R English: https://www.tc.gc.ca/recalls
R French: https://www.tc.gc.ca/rappels Limited
Warranty
* NO
TEDama getotheve hicle arising from
violation of these operating instructions. Damage
totheve hicle can arise from viola‐
tion of these operating instructions.
Such damage is not co veredby either the
Limited Warranty or the new or used-vehicle
wa rrant y. #
Obser vethe instructions in these oper‐
ating instructions on proper operation
of your vehicle as well as rega rding pos‐
sible vehicle damage. QR codes
forre scue card
The QR code sticke rs are af fixe dto the B-pillar on
th e driver's and co-driver's side. In theeve nt of
an accident, emergency services can use the QR
code toquickly de term ine the cor responding res‐
cue card foryo ur vehicle. The cur rent rescue card
contains, in compact form ,th e most impor tant General no
tes27

information about
your vehicle e.g. thero uting of
electric cables.
Fu rther information can be obtained at https://
www.mercedes-benz.de/qr-code. Data
storage Electronic control units
Electronic control units are ins
talled in your vehi‐
cle. Some of them are necessary foryo ur vehicle
to function safel y,some pr ovide support when
driving (driver assis tance sy stems). In addition,
yo ur vehicle of fers comfort or enter tainment
functions which are also made possible with elec‐
tronic control units.
Electronic control units con tain data memo ries
which can permanently or temp orarily store tech‐
nical information on theve hicle's operating state,
component stre ss, service requirements as well
as tech nical events and malfunctions.
This information general lydocuments thest ate of
a component part, a module, a sy stem or of the
environment such as:
R operating statuses of sy stem components
(e.g. fluid le vels, battery status, tire pressure)
R status messages concerning theve hicle and
its individual components (e.g. number of
wheel revo lutions/speed, deceleration, lateral
acceleration, display of thefast ened seat
belts)
R malfunctions or defects in impor tant sy stem
components (e.g. lights, brakes)
R information on events in which theve hicle is
damaged
R system reactions in special driving situations
(e.g. airbag deployment, inter vention of sta‐
bility control sy stems)
R ambient conditions (e.g. temp erature, rain
sensor)
In addition tothe pr ovision of control unit func‐
tions, this data ser vesto recognize and rectify
malfunctions as well as tooptimize vehicle func‐
tions bythe manufacturer. Most of this data is
vo latile and is only processed in theve hicle itself.
Only a small proportion of the data is stored in
ev ent or fault memories.
When you use services, thete ch nical da tafrom
th eve hicle can be read out byservice network
emplo yees (e.g. workshops, manufacturers) or
th ird parties (e.g. breakdown services). Services
include repair services, maintenance processes, wa
rranty events and quality assurance measures,
fo rex ample. The data is read out via the connec‐
tion forth e diagnostics connection in theve hicle,
which is requ ired bylaw. The respective service
network locations or third parties collect, process
and use the data. The data documents tech nical
st ates of theve hicle, helps in finding er rors and
in impr oving quality and is trans ferred tothe
manufacturer if necessar y.In addition, the manu‐
fa cturer is subject toproduct liability. Forth is
purpose, the manufacturer requ ires tech nical
da ta from vehicles.
Fa ult memories in theve hicle can be reset by a
service outlet during repairs or maintenance
wo rk.
Depending on the equipment selected, you can
enter data in com fort and inf otainment functions
of theve hicle.
This includes, forex ample:
R multimedia data, such as music, films or pho‐
to sfo r playback in an integrated multimedia
sy stem
R address book data for use in an integrated
hands-free sy stem or an integrated navigation
sy stem
R navigation destinations entered
R data on the use of Internet services
This data can be sa ved locally in theve hicle or
located on a device that you ha veconnected to
th eve hicle (e.g. smartphone, USB memory stick
or MP3 pla yer). If this data is sa ved in theve hicle,
yo u can dele teit at any time. Trans fer of this data
to third parties only occurs on your requ est,
especially as part of online services according to
th e settings you selec ted.
Yo u can sa vecon venience settings/cus tomiza‐
tions in theve hicle and change them at any time.
Depending on the equipment, this includes, for
ex ample:
R settings of the seat and steering wheel posi‐
tions
R suspension and climate cont rol settings
R customizations such as interior lighting
If yo ur vehicle is equipped appropriately, you can
connect your smartphone or ano ther mobile end
device totheve hicle. You can operate these devi‐
ces via the cont rol elements integrated in the
ve hicle. The smartphone's picture and sound can
be output via the multimedia sy stem. Simultane‐ 28
General no tes

ously, specific items of information are transfer‐
re dto yo ur smartphone.
Depending on the type of integration, this can
include:
R general vehicle data
R position data
This enables the use of selected smartphone
apps, e.g. navigation or music playbac k.There is
no additional interaction between the smart‐
phone and theve hicle, particular lyactive access
to vehicle data. Which type of fur ther data pro‐
cessing occurs is de term ined bythe pr ovider of
th e specific app used. Which settings you can
make, if an y,depends on the specific app and the
operating sy stem of your smartphone. Online services
Wire
less network connection
If yo ur vehicle has a wireless network connection,
data can be exchanged between your vehicle and
ot her sy stems. The wireless network connection
is enabled via theve hicle's transmission and
re ception unit or via connected mobile end devi‐
ces (e.g. sma rtphones). Online functions can be
used via this wireless network connection. These
include online services and applications/apps,
which are pr ovided bythe manufacturer or by
ot her pr oviders.
Manu factu rer's own services
In the case of the manufacturer's online services,
th e manufacturer describes the functions in a
suitable place (e.g. operating instructions, manu‐
fa cturer's website) and pr ovides the associated
information subject todata pr otection legislation.
Pe rsonal identification data may be used topro‐
vide online services. The data exchange forth is
ta ke s place via a secure connection, e.g. with the
manufacturer's IT sy stems intended forth e pur‐
pose. The collecting, processing, and use of per‐
sonal identification data be yond the pr ovision of
services occurs exclusively on the basis of a legal
permit or af ter due consent.
Generally, you can activate or deactivate the
services and functions (partly subject toafe e). In
some cases, this also applies tothe whole data
connection of theve hicle. Excluded from this are
special legally prescribed functions and services.
Services of third parties
If it is possible touse online services from other
pr ov iders, these services are subject tothe data
pr otection and term s of use of there sponsible pr
ov ider. The manufacturer has no influence on
th e contents exchanged whilst using these serv‐
ices.
Please ask there spective service pr ovider for
de tails on the type, extent and pu rpose of the
collection and use of personal da tainthe cont ext
of third party services. Event Data
Recorders USA onl
y:
This vehicle is equipped with an event da ta
re corder (EDR). The main pu rpose of an EDR is to
re cord, in cer tain crash or near crash-like situa‐
tions, su chas an air bag deployment or hitting a
ro ad obs tacle, da tathat will assist in unde rsta nd‐
ing how a vehicle's sy stems per form ed. The EDR
is designed torecord da tarelated tovehicle
dynamics and saf ety sy stems for a short period
of time, typically 30 seconds or less.
The EDR in this vehicle is designed torecord such
da ta as:
R How various sy stems in your vehicle were
operating;
R Whe ther or not the driver and passenger
saf ety belts werebuckled/fas tened;
R How far (if at all) the driver was depressing
th e accelera tor and/or brake pedal; and,
R How fasttheve hicle was tr ave ling.
This data can help pr ovide a better under standing
of the circums tances in whi chcrashes and inju‐
ri es occur. NOTE: EDR data are recorded by your
ve hicle only if a non-trivial crash situation occurs;
no data are recorded bythe EDR under normal
driving conditions and no personal data (e.g.
name, gende r,age and crash location) are recor‐
ded. Ho wever,ot her parties such as law enforce‐
ment could combine the EDR data with the type
of personally identifying data routinely acquired
during a crash in vestigation.
Ac cess totheve hicle and/or the EDR is needed
to read data that is recorded byan EDR, and spe‐
cial equipment is requ ired. In addition totheve hi‐
cle manufacturer, other parties that ha vethe spe‐
cial equipment, such as law enforcement, can
re ad the information byaccessing theve hicle or
th e EDR.
EDR data may be used in civil and criminal mat‐
te rs as a tool in accident reconstruction, accident
claims and vehicle saf ety. Since the Crash Data
Re trie val CDR tool that is used toextract da ta
from the EDR is commercially available, Daimler Gene
ral no tes 29

%
When
youstop automatic operation upon
opening the door, the door closes when you
press the button again.
% In unf
avorable operating conditions, e.g.
frost, ice or heavy soiling, you can press and
hold the cor responding button. The electric
sliding door mo ves with increased forc e.
Obser vethat, in such circum stances, the
object recognition is less sensitive. Tostop
th e mo vement, release the button. Opening/closing
the electric sliding door
with thekey #
Tounlo ck:brie fly press the0042 or0041
button on thekey. #
Toopen: press and hold the0042 or0041
button on theke yfo r longer than 0.5 sec‐
onds.
Yo u will hear two acoustic signals and the
sliding door will open automaticall y.#
Toclose: press and hold the0042 or0041
button on theke yfo r longer than 0.5 sec‐
onds.
Yo u will hear two acoustic signals and the
sliding door will close automaticall y.#
Tointer rupt automatic operation: briefly
press the0042 or0041 button on theke y.
The sliding door stops moving.
% When
youstop automatic operation upon
opening the door, the door closes when you
press the button again. Opening/closing
the electric sliding door
with the door handle #
Tounlo ck:pull lo cking pin 2upwards man‐
ually or use the cent ral locking button to
unlo ckthe sliding door (/ page 49). #
Press button 1or pull outside handle 3.
The sliding door opens or closes. #
Press button 1again or pull outside handle
3.
The sliding door stops moving. Un
locking the electric sliding door manually If
th ere has been a malfunction or if the battery
has been disconnected, you can use release
cat ch2 todisconnect the sliding door from the
electric mo tor.Then, you can open or close the
door manually. #
Vehicles with comple tesliding door trim:
re mo vethe co ver from release cat ch2.
Service ope ration is accessible. 54
Opening and closing

1
Position of motion de tector
If th eve hicle is equipped with a motion de tector,
th e cargo compartment lighting is also activated
via the motion de tector.
If th e motion de tector de tects mo vement in the
cargo compa rtment while theve hicle is station‐
ar y, the cargo compartment lighting will switch
on for appro ximately two minu tes.
The cargo compartment lighting can be switched
on via the motion de tector if:
R The vehicle is stationar y,the parking brake is
applied and you are not depressing the brake
pedal.
R Vehicles with automatic transmission: the
selector le ver is in position 005Dand you are
not depressing the brake pedal.
R The vehicle has not been loc ked from the out‐
side using thekey.
If no change totheve hicle, such as a door open‐
ing, is de tected over se veral hours, the motion
de tector will au tomatically switch off. This pre‐
ve nts the battery from discharging. Switching
the interior lighting switch-off
delay time on/off Multimedia sy
stem:
4 © 5
Settings 5
Light
5 Interior Lighting Delay #
Switch the switch-off delay time on or off.
If th e function is active, the interior lighting
will remain lit up for a short time when the
seat belt buckle is released. Changing bulbs
Instructions
forch anging bulbs &
WARNING Risk of bu rns from hot com‐
ponent parts whilst replacing a bulb
Bulbs, lamps and plug connectors can
become very hot during operation.
When replacing a bulb, you could burn your‐
self on these component parts. #
Allow the component parts tocool
down before replacing the bulbs. When
you are replacing the bulb, obser vethefo l‐
lowing:
R Do not use any bulb that has been dropped or
has scratches on its glass sur face. Otherwise,
th e bulb may explode.
R The bulb may explode if it is hot or if you
to uch, drop or sc ratch it.
R Stains on theglass sur face reduce the
service life of the bulb. Do not touch theglass
sur face wi thyour bare hands. If necessar y,
clean theglass sur face wi thalcohol or spirits
in a cold state and wipe it down with a lint-
free clo th.
R Protect bulbs from humidity and do not bring
th em into contact with liquids.
Alw ays ensure the bulbs are firm ly secu red.
If yo ur vehicle is equipped with LED lamps, you
can check this as follo ws :th e light cone will mo ve
from topto bottom and back again when the
ve hicle starts. Forth is to wo rk,th e low beam
needs tohave been switched on before theve hi‐
cle is star ted.
Bulbs and lamps are a major part of vehicle
saf ety. Therefore, ensure that they are alw ays
wo rking. Ha vethe headlamp setting checkedre g‐
ularly.
R Before changing the bulbs, switch off the
ve hicle's lighting sy stem. This will pr event a
sho rtcircuit.
R Use bulbs only in closed lights that ha vebeen
designed forth em.
R Use only spare bulbs of the same type and
with the cor rect voltage.
If th e new bulb also does not light up, consult a
qu alified specialist workshop. 90
Light and vision

*
NO
TEWearing out the brake linings by
continuously dep ressing the brake pedal #
Do not depress the brake pedal continu‐
ously whilst driving. #
Touse the braking ef fect of the engine,
shift toa lo werge ar in good time. *
NO
TEDama getothe driv etra in and
engine when pulling away #
Do not warm upthe engine while the
ve hicle is stationar y.Pull away immedi‐
atel y. #
Avoid high engine speeds and driving at
full thro ttle until the engine has reached
its operating temp erature. *
NO
TEDama getothe catalytic con verter
due tonon-combu sted fuel The engine is not
running smo othly and is
misfiring.
Non-combus ted fuel may getinto the cata‐
lytic con verter. #
Only depress the accelera tor pedal
slightly. #
Have the cause rectified immedia tely at
a qualified speciali st workshop. Exhaust emission monitoring
Specific engine sy
stems are designed tokeep
poisonous components of exhaust emissions
within legal limits.
These sy stems only workoptimally if they are
main tained exactly according tomanufacturer's
specifications. It is forth is reason that all work
on the engine should only be per form ed byquali‐
fi ed and authorized Mercedes-Benz Center tech‐
nicians.
Under no circum stances should engine settings
be changed. In addition, all specific main tenance
wo rkmust be per form ed at regular inter vals and
in compliance with the service regulations of the
dealer named in the imprint. Referto the Mainte‐
nance Booklet for de tails.
Note s on short-distance trips
If th eve hicle is predominantly used for short-dis‐
ta nce driving, fuel may accumulate in the engine
oil and cause engine damage.
If yo u main lydrive short dis tances, you should
drive on a free way or go for a country drive for 20 minutes
every480 km (300 miles). This facili‐
ta testh ere ge neration of the diesel particulate fil‐
te r.
Note s onthe speed limit &
WARNING Risk of inju rythro ugh exceed‐
ing the specified tire load rating or the
permissible speed rating
Exceeding the specified tire load rating or the
permissible speed rating may lead totire
dama geand tothe tires bur sting. #
Therefore, only use tire types and sizes
appr ovedfo ryo ur vehicle model. #
Obser vethe tire load rating and speed
ra ting requ ired foryo ur vehicle. As
the driver, you must find out about the maxi‐
mum permissible speed forth e tires (tire and tire
pressure). In particular, obser vethe legal requ ire‐
ments for tires forth e count ryyou are in.
Yo u can permanently limit the speed of your vehi‐
cle.
Mercedes-Benz recommends a qualified special‐
ist workshop for programming the speed limit.
No tethat you cannot exceed a programmed limit
speed when overtaking.
On downhill gradients, the speed limit may be
exc eeded. Apply the brakes if necessar y.
Displ aymessages indica tethat you are approach‐
ing the limit speed.
% Fo
r buses, the speed is limited at thefa ctory
to 100 km/h. When overtaking, bear in mind
th at the limit speed cann otbe exc eeded.
Information about driving abroad
Service
An extensive Mercedes-Benz service is also avail‐
able abroad. Ne vertheless, please remember that
services facilities or spa reparts may not be avail‐
able immediatel y.The releva nt wo rkshop directo‐
ri es are available from an authorized Mercedes-
Benz Center.
Fu el
In some countries, only fuels with an inc reased
sulfur con tent are available.
Mercedes-Benz recommends ins talling a fuel fil‐
te r with a water sepa rato rfo r countries with an
increased water content in diesel. Driving and parking
11 3

Uns
uitable fuel can cause engine damage. In for‐
mation about fuel can be found in the "Fuel" sec‐
tion (/ page 341).
Information about transport byrail
Tr ansporting your vehicle byrail may be subject
to cer tain restrictions or require special meas‐
ures tobe take n in some countries due tovarying
tunnel heights and loading standards.
Yo u can obtain information about this from any
authorized Mercedes-Benz Center.
Note s on brakes &
WARNING Risk of skidding and of an
accident due toshifting down on slippery
ro ad sur faces
If yo u shift down on slippery road sur faces to
inc rease the engine braking ef fect, the drive
wheels may lose traction. #
Do not shift down on slippery road sur‐
fa ces toinc rease the engine braking
ef fect. &
WARNING Risk of accident due tothe
brake sy stem overheating
If yo u lea veyour foot on the brake pedal
when driving, the brake sy stem may overheat.
This increases the braking dis tance and the
brake sy stem may evenfa il. #
Never use the brake pedal as a foot re st. #
Do not depress the brake pedal and the
accelerator pedal at the same time
while driving. Downhill
gradients
On long and steep downhill gradients you should
obse rveth efo llowing instructions:
R Invehicles with an automatic transmission,
shift down toshift ranges 2or 1in good time
so that the engine is running at a medium to
high engine speed (/ page124).
% Cha
nge the shift range in good time when
cruise control is acti vated. Obser vethe driv‐
ing tips (/ page111).
Yo uth ereby make use of the braking ef fect of the
engine and do not ha vetobrake as of tento main‐
tai nth e speed. This relie vesth e load on the
service brake and pr events the brakes from over‐
heating and wearing tooqu ickl y. Heavy and light loads
If
th e brakes ha vebeen subjected toa heavy
load, do not stop theve hicle immediatel y.Drive
on for a short while. The brakes cool down more
qu ickly in the air flow.
If th e brakes ha vebeen used only moderately,
yo u should occasionally test their ef fectiveness.
To do this, brake more firm ly from a higher speed
while pa ying attention tothe traf fic conditions.
The brakes will grip better as a result.
We tro ad sur faces
If yo u ha vebeen driving for a long time in heavy
ra in without braking, there may be a dela yed
re sponse when youfirs t apply the brakes. This
may also occur af ter driving thro ugh a car wash
or deep water.Yo u must depress the brake pedal
more firm ly. Maintain a grea ter dis tance tothe
ve hicle in front.
While paying attention tothe traf fic conditions,
yo u should brake theve hicle firm lyafte r driving
on a wetro ad sur face or thro ugh a car wash. This
heats the brake discs so that they dry more
qu ickl y,which pr otects them against cor rosion.
Limited braking ef fect on salt-trea tedro ads:
R A layer of salt on the brake discs or brake‐
pads can increase braking dis tances consid‐
erably, or braking may happen on only one
side
R Maintain an especially large safe dis tance to
th eve hicle in front
To remo vethe la yer of salt:
R Apply the brakes from time totime, paying
attention totraf fic conditions
R Carefully depress the brake pedal at the end
of a journey and af terth est art of a new jour‐
ney
Checking the brakepad thickness
In addition tomonitoring using the brakepad wear
sensor, regular lymonitor and check all of the
brakepads byper form ing a visual inspection to
look for pad material wear.
If yo u are unable tocheck the brakepad wear on
th e inside of the wheels, remo vethe wheels if
yo u possess there qu ired skills, or visit a qualified
specialist workshop.
If th e brakepad material thickness is less than
0. 12 in (3 mm), ha vethe brakepads checked and
re placed at a qualified specialist workshop, if
necessar y.
Do not solely rely on the brakepad wear sensor. 11 4
Driving and pa rking

It is also
strongly recommended that you ha ve
th e brakepads checked at a qualified specialist
wo rkshop, not only at everyservice displa yedby
th e maintenance inter val displa y,but also prior to
long journe ysand when ever the wheels are
re mo ved.
Ne w brake discs and brakepads
New brakepads and brake discs on lyreach their
optimal braking ef fect af ter appro ximately
10 0 miles (100 kilome ters).
Unti lth en, compensate forth ere duced braking
ef fect by applying greater pressure tothe brake
pedal. For saf etyre asons, Mercedes-Benz recom‐
mends that you only ha vebrakepads and brake
discs which are appr ovedby Mercedes-Benz
ins talled on your vehicle.
Other brake discs or brakepads may compromise
th e saf ety of your vehicle.
Alw aysre place all brake discs and brakepads on
an axle at the same time. Alw ays ins tall new
brakepads when replacing brake discs.
Pa rking brake &
WARNING Risk of skidding or an acci‐
dent bybraking with the parking brake
If yo u ha vetobrake your vehicle with the
parking brake, the braking dis tance is consid‐
erab lylonger and the wheels may loc k.There
is an increased risk of skidding and/or acci‐
dent. #
Only brake theve hicle with the parking
brake if the service brake has failed. #
Inthis case, do not apply the parking
brake with too much forc e. #
Ifth e wheels loc k,immediately release
th e parking brake as much as required
fo rth e wheels toturn again. Ve
hicles with a manual parking brake
When driving on wetro ads or dirt-co vered sur fa‐
ces, road salt or dirt may getinto the parking
brake. This causes cor rosion and a reduction of
braking forc e.
In order topreve ntthis, drive with the parking
brake lightly applied from time totime.
When doing so, drive for a dis tance of appr ox‐
imately 300 ftat a maximum speed of 13mph
(20 km/h).
The brake lights do not light up when you brake
th eve hicle with the parking brake. Information about driving on
wetroads
Hydroplaning &
WARNING Risk of aquaplaning because
tire tread is too low
Depending on the dep thofthewate r onthe
ro adw ay, aquaplaning can occur despite suf fi‐
cient tire tread dep thand low speed. #
Avoid tire ruts and brake carefully. The
refore , in heavy rain or other conditions in
which hydroplaning can occur, drive as follo ws:
R Reduce your speed
R Avoid tire ruts
R Brake carefully
Driving on flooded roads
Bear in mind that vehicles tr aveling in front or in
th e opposite direction create waves. This may
cause the maximum permissible dep thofwater
to be exc eeded. These no tes must be obser ved
under all circum stances. Otherwise, you can
damage the engine, electrics and transmission.
If yo u ha vetodrive on stre tches of road on which
wate r has collected, please bear in mind thefo l‐
lowing:
R The wate r level of standing water may not be
abo vethe lo wer edge of the front bumper.
R You may drive no fasterthan walking pace.
Obser vethe no tes on ford ing while off- road for
all-wheel drive vehicles (/ page116).
Infor mation about driving in winter &
DANG ER Risk of fata l injury due topoi‐
sonous exhaust gases
If th eta ilpipe is bloc ked or suf ficient ventila‐
tion is not possible, poisonous exhaust gases
such as carbon monoxide may enter theve hi‐
cle. This is the case when theve hicle
becomes stuck in sn ow,fo rex ample. #
Keep theta ilpipe and the area around
th eve hicle free from snow when the
engine or thest ationary heater are run‐
ning. #
Open a window on the side of theve hi‐
cle facing away from the wind toensure
an adequate supply of fresh air. Driving and parking
11 5