2017 JEEP RENEGADE Owners Manual

Oil Change Reset
Oil Change Due
Your vehicle is equipped with an engine oil change indi-
cator system. The “Oil Change Due” message will display
in the instrument cluster display for five seconds after a
single chime has sounded to indicate the next scheduled oil
change interval. The engine oil change indicator system is
duty cycle based, which means the engine oil change
interval may fluctuate, dependent upon your personal
driving style.
Unless reset, this message will continue to display each
time you turn the ignition is cycled to the ON or RUN
position. To reset the oil change indicator system (after
performing the scheduled maintenance), refer to the fol-
lowing procedure.
1. Without pushing the brake pedal, push the ENGINESTART/STOP button and cycle the ignition to the ON/
RUN position (do not start the engine).
2. Fully push the accelerator pedal, slowly, three times within 10 seconds.
3. Without pushing the brake pedal, push the ENGINE START/STOP button once to return the ignition to the
OFF/LOCK position. NOTE:
If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. See your authorized dealer to have the oil life reset.
Instrument Cluster Display Menu Items
NOTE: The instrument cluster display menu items display
in the center of the instrument cluster. Menu items may
vary depending on your vehicle features.
Speedometer
Push and release the upordown arrow button until the
speedometer menu icon is displayed in the instrument
cluster display. Push and release the OKbutton to toggle
units (mph or km/h) of the speedometer.
Vehicle Info
Push and release the up or down arrow button until
Vehicle Info is highlighted in the instrument cluster
display. Push and release the right arrow button and
Coolant Temp will be displayed. Push the right or left
arrow button to scroll through the following information
displays:
• Tire Pressure — View the information relating to the
TPMS system (If Equipped).
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 127

•Coolant Temperature — View the engine coolant tem-
perature.
• Trans Temperature — View the trans oil temperature.
• Battery Voltage — View the voltage value (state of
charge) of the battery.
• Service — If Equipped — View the service status mes-
sage(s).
Fuel Economy
This menu item allows you to set the unit of measurement
for the Fuel Economy and Range.
• Range (Miles or km)
• Current Consumption (mpg or L/100km or km/l)
• Average Consumption (mpg or L/100km or km/l )
Reset procedure shown at the bottom of the display.
Trip Info
Push and release the upordown arrow button until the
Trip menu title is displayed in the instrument cluster
display. Toggle the leftorright arrow button to select Trip
A or Trip B. The Trip information will display the follow-
ing: •
Distance – Shows the total distance (mi or km) traveled
for Trip A or Trip B since the last reset.
• Average Fuel Economy – Shows the average fuel
economy (MPG or L/100 km) of Trip A or Trip B since
the last reset.
• Elapsed Time – Shows the total elapsed time of travel
since Trip A or Trip B has been reset.
Hold the OKbutton to reset feature information.
Stored Messages
Push and release the upordown arrow button until the
Messages Menu Icon is highlighted in the instrument
cluster display. This feature shows the number of stored
warning messages. Pushing the leftorright arrow button
will allow you to scroll through the stored messages.
Screen Setup
This menu item allows you to change the position of the
information on the display.
128 GETTING TO KNOW YOUR INSTRUMENT PANEL

Display Gears (Vehicles With Reconfigurable Multi-
Functional Display And Automatic Transmission)
By selecting this item, you can select the display mode, the
particulars relating to the automatic transmission, and
choose between the following options:
•Single digit
The right side of the display will show the letter concerning
the automatic transmission gear selector (P,R,N or D)
position. After approximately two seconds, the letter will
be displayed in a central position.
• Full PRND
(Default): The right side of the display the letters PRND,
the position assumed by the gear selector will be high-
lighted in the display. During the operation in sequential
mode (AutoStick), in place of the letter D, the gear will be
will be displayed.
In The Upper-Left/Top Right
The information relating to the following can be displayed:
• External temperature
• Ignition Button — If Equipped
• Compass (If Equipped) •
Date (Month/Day)
• Time (Hours/Minutes)
In the central area of the display, you can view all of the
information listed above as well as the following:
• State of the ignition
• Compass — If Equipped
• Speed Display (If Equipped)
• Date (Day/Month/Year)
• Time
• External Temp — If equipped
• Menu Item
• Distance Traveled A (Trip A)
• Distance Traveled B (Trip B)
Restore Default Settings
Selecting this item, and you can reset and restore the
default settings.
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 129

Settings
This menu item allows you to change the settings for the
following:
•Display
• Units
• Clock and Date
• Security
• Safety and Assistance
• Lights
• Doors and Locks
• Compass
Vehicles Equipped With Multifunctional Display Re-
configurable:
The following menu/submenu items are
available in the cluster display.
“Display”
By selecting the Display,you can access the following
settings:
• Language: allows you to select the language in which to
display the information/warnings. •
Phone
• Navigation
Units Of Measure
By selecting the item Units of Measure,you can select the
unit of measure to use for displaying various magnitudes.
Possible options are:
• US
• Metric
• Custom
Clock & Data
By selecting the item, Clock & Dateyou can adjust the
clock.
Possible options are:
• Set Time: adjust hours/minutes
• Set Format: adjust the time format 12h(12 hours) or
24h (24 hours)
• Set Date: adjust day/month/year
130 GETTING TO KNOW YOUR INSTRUMENT PANEL

Security
By selecting the item “Security,” you can make the follow-
ing adjustments:
•Speed Warning:
Set the vehicle speed limit (km/h or MPH), which the
driver is notified through a visual and acoustic signaling
(display of a message and a symbol on the display).
When the speed warning is set, the icon should remain
visualized for the same duration time of the pop up. If the
driver exceeded the speed set the icon should remain for
however long the vehicle is over the set speed.
Driver may also turn the Speed Warning “OFF” should you
choose not to use this feature.
• Seat Belt Reminder:
This function is only viewable when the Seat Belt Re-
minder (SBR) system is active.
• Hill Start Assist (If Equipped):
Activation/Deactivation of the Hill Start Assist system. Safety & Assistance
By selecting the item
Safety & Assistance, you can make
the following adjustments:
• Forward Collision Warning
• Forward Collision Warning Sensitity
• ParkSense (If Equipped): a selection of the type of
information provided by ParkSense
• Rear Parks (If Equipped) Vol.: selection of the volume of
acoustic signals provided by ParkSense
• ParkSense (If Equipped) Vol.: a selection of the volume
of acoustic signals provided by ParkSense
• Front Parks. Vol.: selection of the volume of the beeps
provided by ParkSense
• Warning Buzzer Volume
• Brake Service (If Equipped): activation of the procedure
to carry out braking system maintenance
• Auto Park Brake (If Equipped): enable/disable auto-
insertion of the Electric Parking Brake
• Rain Sensing Wipers
• Lanesense Warning (If Equipped)
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 131

•Lanesense Strength (If Equipped)
• Side Distance Warning (If Equipped)
• Side Distance Warning Volume (If Equipped)
Lights
By selecting the item Lights,you can make the following
adjustments:
• Headlight Off Delay: set the delay for headlight shutoff
after engine shutoff
• Headlight Sensitivity (If Equipped): adjust the sensitiv-
ity of headlight brightness
• Daytime Running Lights (If Equipped): activate/
deactivate the daytime running lights
• Cornering lights (If Equipped): activate/deactivate the
cornering lights (If Equipped)
• Greeting Lights (If Equipped): activate / deactivate
greeting lights
Doors & Locks
By selecting the item Doors & Locks,you can make the
following adjustments: •
Auto Door Lock (If Equipped): activate/deactivate the
automatic locking of the doors with the vehicle moving
• Auto Unlock On Exit (If Equipped): automatic unlocking
of the doors when exiting the vehicle
• Flash Light with Lock (If Equipped): activate the direc-
tion indicators when closing the doors
• Sound Horn With Lock (If Equipped): activate/
deactivate the horn when pushing the LOCK button on
the key fob. The options are Off,First Press,” and
Second Press
• Horn With Remote Start (If Equipped): activate/
deactivate the horn at the Remote Starting of the engine
with the key fob
• Remote Door Unlock (If Equipped): allows you to open
the driver door only on the first push of the UNLOCK
button on the key fob
• Passive Entry (If Equipped): activate the automatic
locking of the doors
132 GETTING TO KNOW YOUR INSTRUMENT PANEL

Compass (If Equipped)
By selecting the itemCompass,you can make the follow-
ing adjustments:
• Compass Calibration
• Compass Variance
TRIP COMPUTER
The Trip computer is used to display information on car
operation when the key is turned to the RUN position.
This function allows you to define two separate trips called
“Trip A” and “Trip B” where the car’s complete tripsare
monitored in an independent manner.
Both trips can be reset (reset - start of a new trip). To
perform a reset, push and hold the OKbutton on the
steering wheel controls.
“Trip A” and “Trip B” are used to display the figures
relating to:
• Distance Travelled
• Average Consumption
• Travel Time (driving time) Quantities Displayed
Distance Travelled
•
Indicates the distance travelled by the start of the new
trip.
Average Consumption
• Represents the average fuel consumption since the start
of the new trip.
Travel Time
• Elapsed time since the start of the new trip.
OK Button
Short Push Of The Button: display of various parameters.
Long Push Of The Button: reset quantities and begin a new trip.
New trip
Starts after reset:
• Manual by pushing the OKbutton.
• Automatic when thedistancereaches the value is
62140 (99999.9 km) or when the time travelreaches the
value of 999.59 (999 hours and 59 minutes).
• After each disconnection and reconnection of the battery.
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 133

WARNING/INDICATOR LIGHTS AND MESSAGES
The warning/indicator light switches on in the instrument
panel together with a dedicated message and/or acoustic
signal when applicable. These indications are indicative
and precautionary and as such must not be considered as
exhaustive and/or alternative to the information contained
in the Owner Manual, which you are advised to read
carefully in all cases. Always refer to the information in this
chapter in the event of a failure indication.All active telltales will display first, if applicable. The
system check menu may appear different based upon
equipment options and current vehicle status. Some tell-
tales are optional and may not appear.
The following warning lamps and indicators will alert you
to a vehicle condition that may become serious. Some
lamps will illuminate when you start your vehicle to make
sure they work. If any lamps remain on after starting your
vehicle, refer to the respective system warning lamp for
further information.
Red Telltale Lights
Seat Belt Reminder Warning Light
Red Telltale
Light What It Means
Seat Belt Reminder Warning Light
When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight sec-
onds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will
sound. After the bulb check or when driving, if the driver ’s seat belt remains unbuckled, the Seat
Belt Reminder Light will flash or remain on continuously and a chime will sound. Refer to “Oc-
cupant Restraint Systems” in “Safety” for further information.
134 GETTING TO KNOW YOUR INSTRUMENT PANEL