2016 MITSUBISHI SHOGUN Owner's Manual (in English)

Engine compartment fuse loca-tion table
E01008001913
Engine compartment fuse location (Type A)
No.SymbolElectrical systemCapaci- ty1Alternator140 A *12Fuse (+B)60 A*13Ignition
switch40 A *1*1
: Fusible link
*2 : Vehicles without discharge headlamps
*3 : Vehicles with discharge headlampsNo.SymbolElectrical
systemCapaci- ty4Electric win-dow control30 A *15Engine con-
trol20 A *16Fuel pump20 A7Rear heater25 A8Accessory
socket25 A9Fuel line heat- er25 A10Condenserfan motor25 A11Rear air con- ditioning20 A
12
Horn (Theft-
alarm system)
15 A
Wiper de-icer13Horn10 A14Automatic
transmission20 A*1 : Fusible link
*2 : Vehicles without discharge headlamps
*3 : Vehicles with discharge headlampsNo.SymbolElectrical
systemCapaci- ty15Hazard warn-ing flasher10 A16Stop lamps15 A17Radio10 A18Room lamp15 A19Air condition- ing10 A20Front foglamps15 A21———22Windscreen wiper20 A23Tail lamp(right)7.5 A24Tail lamp (left)7.5 A25Headlamp lowbeam (right)10 A *220 A*326Headlamp low
beam (left)10 A *2*1
: Fusible link
*2 : Vehicles without discharge headlamps
*3 : Vehicles with discharge headlamps
Fuses
10-22OVWE16E1Maintenance10

No.SymbolElectricalsystemCapaci- ty20 A *327
Headlamp
high-beam (right)
10 A28
Headlamp
high-beam (left)
10 A29Audio40 A *130Heater50 A*1*1
: Fusible link
*2 : Vehicles without discharge headlamps
*3 : Vehicles with discharge headlamps
l Some fuses may not be installed on your
vehicle, depending on the vehicle model
or specifications.
l The table above shows the main equip-
ment corresponding to each fuse.Engine compartment fuse location (Type B)No.SymbolElectrical systemCapaci- ty31Anti-lock
brake system60 A *32Brake system40 A*33Glow relay80 A**
: Fusible link
l Some fuses may not be installed on your
vehicle, depending on the vehicle model
or specifications.
l The table above shows the main equip-
ment corresponding to each fuse.
Identification of fuse
E01008100164
Ca-
pacityColour7.5 ABrown10 ARed15 ABlue20 AYellow (fuse type)/Light blue (fu- sible link type)25 ATransparent30 AGreen (fuse type)/
Pink (fusible link type)40 AGreen50 ARed60 AYellow80 ABlack140 AReddish brownFuse replacement
E01007801901
1. Before replacing a fuse, always turn off
the electrical circuit concerned and place
the ignition switch in the “LOCK” posi-
tion.
2. Pull the fuse block lid (A) to remove it.
Fuses
10-23OVWE16E1Maintenance10

3. Remove the fuse puller (B) from the fuseblock lid.
4.The replacement of fuses located in the
driver’s seat leg area should be per- formed from the hole of the fuse block
lid.
5. Referring to the fuse load capacity table,
check the fuse pertaining to the problem.
C- Fuse is OK
D- Blown fuse
NOTEl If any system does not function but the fuse
corresponding to that system is normal, theremay be a fault in the system elsewhere. We recommend you to have your vehiclechecked.
6. Insert a new fuse of the same capacity
by using the fuse puller into the same
place at the fuse block.
CAUTIONl If the newly inserted fuse blows again after a
short time, we recommend you to have the electrical system checked to find the causeand rectify it.
l Never use a fuse with a capacity larger than
that specified or any substitute, such as wire,
foil, etc.; doing so will cause the circuit wir-
ing to heat up and could cause a fire.Replacement of lamp bulbs
E01003100521
Before replacing a bulb, ensure the lamp isoff. Do not touch the glass part of the new
bulb with your bare fingers; the skin oil left
on the glass will evaporate when the bulb gets hot and the vapour will condense on the
reflector and dim the surface.
Replacement of lamp bulbs
10-24OVWE16E1Maintenance10

CAUTIONlBulbs are extremely hot immediately after
being turned off.
When replacing a bulb, wait for it to cool
sufficiently before touching it. You could otherwise be burnt.NOTEl Do not attempt to repair or replace the lamp
bulbs other than described in this owner’s manual. For repair or replacement, contact aMITSUBISHI MOTORS Authorized Serv-
ice Point.
l If you are unsure of how to carry out the
work as required, we recommend you to consult a specialist.
l Be careful not to scratch the vehicle body
when removing a lamp or lens.
l When it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon as when window glass mists up on a humid
day, and does not indicate a functional prob- lem. When the lamp is switched on, the heat
will remove the fog. However, if water gath-
ers inside the lamp, we recommend you to have it checked.Bulb capacity
E01003200014
When replacing a bulb, use a new bulb with
the same wattage and colour.
Outside
E01003304303
1- Headlamps, high-beam: 65 W (H9)2- Position and Daytime running lamps*
3- Front fog lamps*: 55 W (H11)
4- Headlamps, low beam with discharge
lamp: 35 W
Headlamps, low beam without discharge lamp: 55 W (H11)
5- Position lamps: 5 W (W5W)
6- Front turn-signal lamps: 21 W
(WY21W)
7- Side turn-signal lamps (on fender)*: 5 W
8- Side turn-signal lamps (on outside rear-
view mirror)*
Codes in parentheses indicate bulb
types.CAUTIONl On vehicles with discharge headlamps, do
not attempt to disassemble or repair dis-
charge headlamps, and do not attempt to re- place their bulbs. A high voltage is presentin the power circuit and in the bulbs andbulb terminals. To avoid the risk of an elec-
tric shock, contact by a MITSUBISHI
MOTORS Authorized Service Point when-
ever repair or replacement is necessary.NOTEl The following lamps are not possible to re-
pair or replace only the bulb.
If you need to repair or replace these lamp
bulbs, contact a MITSUBISHI MOTORS
Authorized Service Point.
• Position and Daytime running lamps
• Side turn-signal lamps (on fender)
• Side turn-signal lamps (on outside rear-
view mirror)
Replacement of lamp bulbs
10-25OVWE16E1Maintenance10 Front

1-High-mounted stop lamp (bulb type)*:
16 W (W16W)
2- Licence plate lamps: 5 W (W5W)
3- Rear fog lamp: 21 W (W21W)
4- Tail lamps*: 5 W (W5W)
5- Rear turn-signal lamps*: 21 W
(WY21W)
6- Rear turn-signal lamps*: 21 W
(WY21W)
7- Stop and tail lamps*: 21/5 W (W21/5W) Stop lamps*: 21/5 W (W21/5W)
8- Reversing lamps: 21 W (W21W)
Codes in parentheses indicate bulb
types.NOTEl On vehicles with LED type high-mounted
stop lamp, do not attempt to repair or replaceit.
For repair and replacement, contact a
MITSUBISHI MOTORS Authorized Serv-
ice Point.Inside
E01003403118
1- Luggage compartment lamp: 8 W
2- Door courtesy lamps: 3.4 W
3- Vanity mirror lamps* 2 W
4- Room & map lamps: 8 W
5- Rear personal lamps: 8 W
6- Glove box lamp: 1.4 W
Headlamps
E01003501199
Replacement of high-beam
1. Remove the bulb and connector assem-
bly (A) by turning it anticlockwise.
2. Depress the tab (B) on the harness con-
nector and pull the harness connector
(C) to remove it.
Replacement of lamp bulbs
10-26OVWE16E1Maintenance103-door models5-door models
Rear

3.To install the bulb, perform the removal
steps in reverse.
Replacement of low beam (ex-
cept for vehicles with discharge
headlamps)
1. Remove the bulb and connector assem-
bly (A) by turning it anticlockwise.
2. Depress the tab (B) on the harness con-
nector and pull the harness connector
(C) to remove it.
3. To install the bulb, perform the removal
steps in reverse.
CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres- surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the headlamps are op-
erated. If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., andrefit it after drying it thoroughly.Position lamps (except for vehi-
cles with discharge headlamps)
E01003702332
1. Turn the bulb socket anticlockwise to re-
move it.
2. Remove the bulb from the socket by
pulling out.
3. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-27OVWE16E1Maintenance10

Front turn-signal lamps
E01003800733
1. Turn the bulb socket anticlockwise to re-
move it.
2. Remove the bulb from the socket by
pulling out.
3. To install the bulb, perform the removal
steps in reverse.
Front fog lamps*
E01004002983
1. Remove the 5 clips (A, C) and screw (B)
by following procedures then turn up the cover (D).
2. Depress the tab (E) on the harness con-
nector (F) and pull the harness connector
to remove it.
3. Remove the entire socket and bulb as-
sembly (G) by turning it anticlockwise.CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres-
surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the fog lamps are op- erated. If the glass surface is dirty, it must becleaned with alcohol, paint thinner, etc., and
refit it after drying thoroughly.
Replacement of lamp bulbs
10-28OVWE16E1Maintenance10

4.To install the bulb, perform the removal
steps in reverse.
NOTEl When refitting the clips (H and I) of the cov-
er, push the pin (J).Rear combination lamps
E01004200659
On corner side
1. Remove the screws that hold the lamp
unit.
2. Slide the lamp unit out sideways to re-
move it.
Left sideRight side3. Remove the socket and bulb assemblies
by turning them anticlockwise. Remove the bulb by pulling it out.3-door models5-door models
A- Rear turn-signal lamp* B- Stop and tail lamp* Stop lamp*
C- Reversing lamp
4. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-29OVWE16E1Maintenance10