2016 MITSUBISHI SHOGUN Owner's Manual (in English)

Headlamp levellingE00517400015Headlamp levelling switch*
E00517501895
Except for vehicles with dis-
charge headlamps
The angle of the headlamp beam varies de- pending on the load carried by the vehicle.The headlamp levelling dial can be used to
adjust the headlamp illumination distance (when the lower beam is illuminated) so that
the headlamps’ glare does not distract other drivers.
Set the dial according to the following table.
LHDRHD
CAUTIONl Always perform adjustments before driving.
Do not attempt to adjust while driving, as it could cause an accident.NOTEl When adjusting the beam position, first put
the dial in the “0” position (the highest beamposition).
3-door models
Except for vehicles with only the front
seats
Vehicle conditionSwitch position“0”“0”“2”Vehicle conditionSwitch position“3”“4”●:1 person:Full luggage loadingSwitch position 0-Driver only/ Driver + 1
front passengerSwitch position 2-5 passengers (including
driver)Switch position 3-5 passengers (including
driver) + Full luggage loadingSwitch position 4-Driver + Full luggageloading
Vehicles with only the front seats
Vehicle conditionSwitch position“0”
Headlamp levelling
5-40OVWE16E1Instruments and controls5

Vehicle conditionSwitch position“4”●:1 person:Full luggage loadingSwitch position 0-Driver onlySwitch position 4-Driver + Full luggageloading
5-door models
Except for vehicles with only the front seats
Vehicle conditionSwitch position“0”“0”Vehicle conditionSwitch position“1”“2”“3”“3” or “4”●:1 person:Full luggage loadingSwitch position 0-Driver only/ Driver + 1
front passengerSwitch position 1-Driver + 1 front passen- ger + 2 passengers on
third seatSwitch position 2-7 passengers (including
driver)Switch position 3-7 passengers (including
driver) + Full luggage loading/ Driver + Full luggage loading
{Vehicles except for Russia, Kazakhstan, Be-
larus, Ukraine and Azer-
baijan}Switch position 4-Driver + Full luggage loading
{Vehicles for Russia,
Kazakhstan, Belarus, Ukraine and Azerbaijan}
Vehicles with only the front seats
Vehicle conditionSwitch position“0”“4”●:1 person:Full luggage loadingSwitch position 0-Driver only
Headlamp levelling
5-41OVWE16E1Instruments and controls5

Switch position 4-Driver + Full luggageloadingAutomatic headlamp levelling*
E00517601577
This function automatically adjusts the illu-
mination distance of the headlamps according
to the number of people and the load in the vehicle.
When the ignition switch is in the “ON” posi-
tion and the lamp switch is in the “
” posi-
tion, the illumination distance of the head-
lamps is automatically adjusted when the ve-
hicle is stopped.
Automatic headlamp levelling
warning lamp
E00525901045
The automatic headlamp levelling warning lamp should illuminate when the ignition switch is turned “ON”, and should go off in a
few seconds.
CAUTIONl If the warning lamp stays on or does not illu-
minate when the ignition switch is turned
“ON”, it indicates that the automatic head- lamp levelling device is not functioning.
We recommend you to have your vehicle in- spected.Turn-signal lever
E00506500928
1- Turn-signalsWhen making a normal turn, use posi-
tion (1). The lever will return automati-
cally when cornering is completed.
2- Lane-change signals When changing lanes, use position (2). It
will return to the neutral position when released.
Also, when you move the lever to (2)
slightly then release it, the turn-signal
lamps and indication lamp in the instru-
ment cluster will flash 3 times.
NOTEl If the lamp flashes unusually quickly, the
bulb in a turn-signal lamp may have burned out. We recommend you to have the vehicle
inspected.
l It is possible to activate the following func-
tions. For further information, we recom-
mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
• Sounding of a buzzer as the turn-signal
lamps flash.
• Flashing of the turn-signal lamps when
the lever is operated with the ignition switch in the “ACC” position.
• The turn-signal lamps 3-flash function for
lane changes can be deactivated.
• The time required to operate the lever for
the 3-flash function can be adjusted.Hazard warning flasher
switch E00506600440
Use the hazard warning flasher switch when
the vehicle has to be parked on the road for
any emergency.
The hazard warning flashers can always be operated, regardless of the position of the ig-
nition key.

Push the switch to turn on the hazard warning flashers, all turn-signal lamps flash continu-
ously.
Turn-signal lever
5-42OVWE16E1Instruments and controls5

To turn them off, push the switch again.NOTElIt is possible for a buzzer to sound with
flashing of the turn-signal lamps. For further information, we recommend you to consult aMITSUBISHI MOTORS Authorized Serv-
ice Point.Fog lamp switch
E00506700047Front fog lamp switch*
E00508301839
The front fog lamps illuminate only when theheadlamps or tail lamps are on. Push the
switch to turn on the front fog lamps, and push the switch again to turn them off.
The indication lamp in the instrument cluster
will illuminate while the front fog lamps are
on.LHDRHD
NOTEl The front fog lamps are automatically turned
off when the headlamps or tail lamps are turned off. To turn on the front fog lamps again, push the switch again when the head-
lamps or tail lamps turn on.
l Do not use fog lamps except in conditions of
fog, otherwise excessive lamp glare may temporarily blind oncoming vehicle drivers.Rear fog lamp switch
E00508401739
The rear fog lamp illuminates only when the
headlamps or front fog lamps (if so equipped)
are on.
Push the switch to turn on the rear fog lamp, and push the switch again to turn it off.
The indication lamp in the instrument cluster
will illuminate while the rear fog lamp is on.
Type 1
LHDRHD
Fog lamp switch
5-43OVWE16E1Instruments and controls5

Type 2LHDRHD
NOTElThe rear fog lamp is automatically turned off
when the headlamps or front fog lamps (if so
equipped) are turned off.
To turn on the rear fog lamp again, push the switch again when the headlamps or front
fog lamps (if so equipped) turn on.Wiper and washer switch
E00507101191CAUTIONlIf the washer is used in cold weather, the
washer fluid sprayed against the glass may
freeze, which may hinder visibility. Warm the glass with the defroster or rear window
demister before using the washer.Windscreen wipers
E00516900273
Except for vehicles with rain
sensor
The windscreen wipers can be operated with
the ignition switch in the “ON” or “ACC” position.
If the blades are frozen to the windscreen or
rear window, do not operate the wipers until the ice has melted and the blades are freed,
otherwise the wiper motor may be damaged.MIST-Misting function
The wipers will operate once.OFF-OffINT-Intermittent (Speed sensitive)LO-SlowHI-Fast
Wiper and washer switch
5-44OVWE16E1Instruments and controls5

To adjust intermittent intervals
With the lever in the “INT” (speed-sensitive)position, the intermittent intervals can be ad-justed by turning the knob (A).
1- Fast
2- Slow
NOTEl The speed-sensitive-operation function of
the windscreen wipers can be deactivated.
For further information, we recommend you to consult a MITSUBISHI MOTORS Au-
thorized Service Point.
Misting function
The misting function can be used when the
ignition switch is in the “ON” or “ACC” po- sition.
The wipers will operate once if the wiper lev-
er is raised to the “MIST” position and re-
leased. This operation is useful when it is drizzling, etc. The wipers will continue to op-erate while the lever is held in the “MIST”
position.Vehicles with rain sensor
E00526401773
The windscreen wipers can be operated with the ignition switch in the “ON” or “ACC”
position.
If the blades are frozen to the windscreen or
rear window, do not operate the wipers until
the ice has melted and the blades are freed,
otherwise the wiper motor may be damaged.MIST-Misting function
The wipers will operate once.OFF-OffAUTO-Auto-wiper control
Rain sensor
The wipers will automatically op- erate depending on the degree of
wetness on the windscreen.LO-SlowHI-Fast
Rain sensor
Can only be used when the ignition switch is in the “ON” position.
Wiper and washer switch
5-45OVWE16E1Instruments and controls5

If the lever is put in the “AUTO” position,the rain sensor (A) will detect the extent of
rain (or snow, other moisture, dust, etc.) and the wipers will operate automatically.
Keep the lever in the “OFF” position if the windscreen is dirty and the weather is dry.
Wiper operation under these conditions can scratch the windscreen and damage the wip-
ers.CAUTIONl With the ignition switch in the “ON” posi-
tion and the lever in the “AUTO” position,the wipers may automatically operate in the situations described below.
If your hands get trapped, you could suffer injuries or the wipers could malfunction. Be sure to turn the ignition switch to the “OFF”
position or move the lever to the “OFF” po-
sition to deactivate the rain sensor.
• When cleaning the outside surface of the
windscreen, if you touch the rain sensor.
• When cleaning the outside surface of the
windscreen, if you wipe with a cloth the
rain sensor.
• When using an automatic car wash.
• A physical shock is applied to the wind-
screen.
• A physical shock is applied to the rain
sensor.NOTEl To protect the rubber parts of the wipers,
this operation of the wipers does not take
place even if the lever is put in the “AUTO” position when the vehicle is stationary and
the ambient temperature is about 0 °C or lower.
l Do not cover the sensor by affixing a sticker
or label to the windscreen. Also, do not put any water-repellent coating on the wind-screen. The rain sensor would not be able to
detect the extent of rain, and the wipers
might stop working normally.NOTEl In the following cases, the rain sensor may
be malfunctioning.
Have the vehicle inspected at a MITSUBISHI MOTORS Authorized Serv-
ice Point.
• When the wipers operate at a constant in-
terval despite changes in the extent of
rain.
• When the wipers do not operate even
though it is raining.
l The wipers may automatically operate when
things such as insects or foreign objects are affixed to the windscreen on top of the rainsensor or when the windscreen is frozen.
Objects affixed to the windscreen will stop
the wipers when the wipers cannot remove them. To make the wipers operate again,
place the lever in the “LO” or “HI” position.
Also, the wipers may operate automatically due to strong direct sunlight or electromag-
netic wave. To stop the wipers, place the lever in the “OFF” position.
l Contact a
MITSUBISHI MOTORS Author-
ized Service Point when replacing the wind- screen or reinforcing the glass around the
sensor.
Wiper and washer switch
5-46OVWE16E1Instruments and controls5

To adjust the sensitivity of the rain sensor
With the lever in the “AUTO” (rain sensor)
position, it is possible to adjust the sensitivity of the rain sensor by turning the knob (A).
“+”-Higher sensitivity to rain“-”-Lower sensitivity to rainNOTEl It is possible to activate the following func-
tions. For further information, we recom- mend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
• Automatic operation (rain droplet sensi-
tive) can be changed to intermittent opera-
tion (vehicle-speed sensitive).
• Automatic operation (rain droplet sensi-
tive) can be changed to intermittent opera-
tion (except vehicle-speed sensitive).Misting function
Move the lever in the direction of the arrow
and release, to operate the wipers once.
Use this function when you are driving in
mist or drizzle.
The wipers will operate once if the lever is raised to the “MIST” position and released
when the ignition switch is in the “ON” or “ACC” position. The wipers will continue to
operate while the lever is held in the “MIST” position.
With the ignition switch in the “ON” posi-
tion, if the lever is moved to the AUTO posi- tion and pulled towards you a little, the wip-ers operate once.
The wipers will operate once if the lever is moved to the “AUTO” position and the knob
(A) is turned in the “+” direction when the ig-
nition switch is in the “ON” position.
Wiper and washer switch
5-47OVWE16E1Instruments and controls5