2016 MITSUBISHI SHOGUN Owner's Manual (in English)

6.Install a new battery with the + side (A)
down.
7. Close the remote control transmitter
firmly.
8. Place the remote control transmitter in
the remote control switch case, then se- curely close the remote control switch case.
9. Check the keyless entry system to see
that it works.
Doors
E00300401177CAUTIONlMake sure the doors are closed: driving with
doors not completely closed is dangerous.
l Never leave children in the vehicle unatten-
ded.CAUTIONl Be careful not to lock the doors while the
key is inside the vehicle.
To lock or unlock with the key
1- Lock
2- Unlock
To lock or unlock from inside
the vehicle
1- Lock
2- Unlock
Pull the inside door handle towards you to
open the door.
To lock without using the key
Front door
Doors
3-06OVWE16E1Locking and unlocking3+ side
- side
Coin type battery
CR1616

Set the inside lock knob (1) to the locked po-
sition, and while pulling the outside handle up (2), close the door (3).
Rear door (5-door models)
Set the inside lock knob (1) to the locked po-
sition, and close the door (2).
“Forgotten-key-prevention”
mechanism
E00300600273
If the key is in the ignition switch when you push the lock knob forward with the driver’s
door open, the lock knob will automatically return to the unlocked position.
Central door locks
E00300801692NOTElEach of the doors can be locked or unlocked
independently by using the inside lock knob.
l Repeated continuous operation between lock
and unlock could activate the central door
locking systems built-in protection circuit
and prevent the system from operating.
If this occurs, wait approximately 1 minute before operating the central door lock switch
or the key.
Driver’s door with key (except
for vehicles with keyless entrysystem)
Using the key on the driver’s door locks or unlocks all doors (including the backdoor).
1- Lock
2- Unlock
Driver’s door with central door
lock switch
Using the central door lock switch locks or unlocks all doors (including the backdoor).
1- Lock
2- Unlock
Central door locks
3-07OVWE16E1Locking and unlocking3

“Child-protection” reardoors (5-door models) E00300900869
1- Lock
2- Unlock
Child protection helps prevent the rear doors
from being opened accidentally from the in- side.
If the lever is set to the locked position, the
rear door cannot be opened using the inside handle, but only with the outside handle.
If the lever is set to the “Unlock” position,
the child protection mechanism does not
function.
CAUTIONl When driving with a child in the rear seat,
please use the child protection to prevent ac-
cidental door opening which may cause an accident.Approach lamps*
E00306100195
The lamps (A) in the bottom of each mirror
come on to illuminate road surface while people are entering or exiting the vehicle.
These lamps turn on/off as follows:
l The lamps come on for approximately
15 seconds when all of the doors (in- cluding the backdoor) are unlocked us-
ing the central door lock function or the keyless entry system (if so equipped).
l When any door or the backdoor is
opened, the lamp comes on for approxi-
mately 2 minutes.
If all of the doors (including the back- door) are closed while the lamps are on,
the lamps go off 30 seconds later.NOTEl The lamps go off immediately if any of the
following actions is taken while the lampsare on.
• The ignition switch is turned to the “ON”
position.
• All of the doors (including the backdoor)
are locked using the central door lock function.
• All of the doors (including the backdoor)
are locked using the keyless entry system
(if so equipped).Backdoor
E00301300424WARNINGlIt is dangerous to drive with the backdoor
open since carbon monoxide (CO) gas can
enter the cabin. You cannot see or smell CO. It can cause unconsciousness and
even death.
“Child-protection” rear doors (5-door models)
3-08OVWE16E1Locking and unlocking3

CAUTIONlWhen the backdoor is open, the rear-right
combination lamp is obscured by the spare wheel.
If the backdoor is opened while the vehicle is parked on the road, alert other road users
to the vehicle’s presence using a warning tri- angle or other device as required by local legislation.
l When closing the backdoor, always ensure
your or other person’s fingers cannot be
caught by the backdoor.NOTEl The backdoor is equipped with an oil damp-
er type backdoor stopper, enabling you to hold the backdoor at a desired position.
l While opening or closing the backdoor, you
may feel slight resistance. This is a structural
feature of the backdoor stopper that supports the backdoor and does not indicate any ab-normality.To lock or unlock from outside
the vehicle (Except for vehicles with keyless entry system)
1- Lock
2- Unlock
To lock or unlock from inside
the vehicle
The backdoor can be locked or unlocked by
using the central door lock switch.
1- Lock
2- Unlock
Vehicles without keyless entry system, if the
backdoor is locked or unlocked by using the central door lock switch, it can still be locked
or unlocked with the key.
NOTEl Repeated continuous operating between lock
and unlock could cause the central doorlock’s built-in protection circuit to preventthe system from operating. If this occurs,
wait approximately 1 minute before operat-
ing the central door lock switch.
Backdoor
3-09OVWE16E1Locking and unlocking3

NOTElWhen the luggage compartment lamp is set
to the [•] position, the luggage compartment
lamp illuminates when the backdoor is opened and turns off when it is closed.
To open
Pull the outside handle towards you to open
the backdoor.
Backdoor stopper
Open the backdoor fully and then move the
locking tube (A) to the LOCK position (B); this will ensure that the backdoor remains inthe fully opened position. To subsequently release the stopper, move the locking tube
back to the UNLOCK position (C).
CAUTIONl When closing the backdoor, be careful not to
trap your hands.
l Before closing the backdoor, make sure that
the locking tube (A) is in the UNLOCK po-
sition (C). Closing the backdoor with the
locking tube (A) in the LOCK position (B) may damage the backdoor stopper, rendering
the backdoor unable to be closed.Security alarm system*
E00301500657
The security alarm system is designed to pre- vent unlawful entry into the vehicle. It will
alert people nearby if a door, the backdoor, or the bonnet is opened when the vehicle has
not been unlocked using the keyless entry system.
Also, the alarm will be activated if any of the
following occur.
l Attempt an unlawful moving of the vehi-
cle. (the vehicle inclination detection function)
l Detect a motion in the vehicle. (the inte-
rior intrusion detection function)
l Disconnect the battery terminal.
The security alarm system is set to “active” when the vehicle leaves the factory.
When making changes to the settings, please
follow the procedure listed in the section ti- tled “Changing the system settings” on page
3-12.CAUTIONl Do not modify or add parts to the security
alarm system.
Doing so could cause the security alarm to malfunction.
Security alarm system*
3-10OVWE16E1Locking and unlocking3

NOTElThe alarm system will not be activated if the
doors (including the backdoor) have been
locked using a key or the central door lock switch (instead of the keyless entry system).
l If the turn-signal lamps do not blink after the
locking and unlocking operation using thekeyless entry system, the security alarm sys-
tem may be malfunctioning.
Have the vehicle inspected at a MITSUBISHI MOTORS Authorized Serv-
ice Point.
l In the following situations, the security
alarm system could be more likely to be ac-
cidentally activated.
• Using a car wash
• Taking the vehicle on a ferry
• Parking in an automated car park
• Leaving someone or a pet in the vehicle
• Leaving a window, door, or the sunroof
open
• Leaving an unstable object such as a stuf-
fed toy or accessory in the vehicle
• Suffering a continuous impact or vibra-
tion by hail, thunder, etc.
l The sensitivity of the vehicle inclination de-
tection function and the interior intrusion de-
tection function can be adjusted. For details,
please contact a MITSUBISHI MOTORS
Authorized Service Point.The security alarm has four
modes:
System preparation mode (ap- prox. 20 seconds)
(The buzzer sounds intermittently, and the se-
curity alarm indicator (A) blinks)
The system preparation time extends from the point at which all of the doors (including the backdoor) are locked by the keyless entry
switch to the point at which the system acti- vation mode goes into effect.
During this time, it is possible to temporarily
open a door without using the keyless entry system and without causing the alarm to sound (for example, when you forget some-
thing inside the vehicle or realize that a win- dow is open).
System armed mode
(The buzzer stops, and the security alarm in-
dicator continues to blink slowly)
Once the system preparation mode has ended,
the system armed mode starts. If an unlawful
opening of any of the doors (including the backdoor) or the bonnet is detected during
the system armed mode, the alarm will be ac- tivated to warn people around the vehicle of
an abnormal condition.
Also, if unlawful moving of the vehicle is at-
tempted or a vehicle intrusion is detected, the alarm will be activated.
Alarm activation
The turn-signal lamps blink and the siren
sounds for approximately 30 seconds. Refer
to “Alarm activation” on page 3-15.
NOTEl The alarm will resume if unlawful actions
are taken again, even if the alarm has stop-
ped.
System cancellation
It is possible to cancel the system activation
during the system preparation mode or the system armed mode.
In addition, it is possible to cancel the alarm
once it has been activated.
Security alarm system*
3-11OVWE16E1Locking and unlocking3

Refer to “Cancelling the system” on page3-14, “Cancelling the alarm” on page 3-15.NOTEl When lending the vehicle to another person
or allowing the vehicle to be driven bysomeone who is unfamiliar with the securityalarm system, be sure to give the person a
proper explanation of the security alarm sys- tem or set the security alarm system to the
“inactive” mode.
If a person who is unfamiliar with the securi-
ty alarm system accidentally unlocked the vehicle, causing the alarm to sound, the
alarm would be a nuisance to people nearby.Changing the security alarm
settings
E00301601378
It is possible to set the security alarm to the “active” mode or “inactive” mode.
Follow the procedure below. 1. Remove the key from the ignition
switch.
2. Place the lamp switch in the “OFF” posi- tion, and leave the driver’s door open.
3.Pull the windscreen wiper and washer
switch towards you and hold it there.
(Since the ignition switch is in the
“LOCK” position, washer fluid will not be sprayed.)
4. After approximately 10 seconds, the
buzzer will make a sound. Keep the windscreen wiper and washer switch
pulled towards you.
(If the windscreen wiper and washer
switch was released, the setting change
mode would be cancelled. To start over, perform the procedure again from step
3.)
5. When the buzzer stops, with the wind-
screen wiper and washer switch stillpulled towards you, press the UNLOCKswitch (A) on the keyless entry switch toselect the security alarm settings mode.
Security alarm system*
3-12OVWE16E1Locking and unlocking3

The settings mode can be toggled by
pressing the UNLOCK switch. The mode can be confirmed from the numberof times the buzzer sounds.
Number of
times the buzzer soundsSecurity alarm settings mode1Alarm inactive3Alarm active
6.Any of the following operations can be
used to terminate the system settings change mode. •Releasing the windscreen wiper and
washer switch.
• Closing the driver’s door.
• Inserting the key into the ignition
switch.
• Placing the lamp switch in any posi-
tion other than “OFF”.
• Allowing 30 seconds to pass with-
out making any changes to the set-
tings.NOTEl If anything with regard to making changes to
the security alarm system settings is hard to understand, please consult a MITSUBISHI
MOTORS Authorized Service Point.
l Avoid leaving valuable items inside the ve-
hicle even when the security alarm system has been set to the “active” mode.Setting the system
E00301702028
Once the security alarm system has been set
to the “active” mode, follow the procedure below to set the system to the system armed
mode. 1. Remove the key from the ignition
switch.
2. Exit the vehicle and close all of the
doors (including the backdoor) and the
bonnet.
3. Press the LOCK switch (A) on the key-
less entry switch in order to lock all thedoors (including the backdoor).
By locking the vehicle using the keyless entry system, the system preparation
mode is activated. The buzzer sounds in-
termittently for confirmation, and the se-
curity alarm indicator (B) on the instru- ment panel blinks.
Security alarm system*
3-13OVWE16E1Locking and unlocking3