2009 RENAULT TWINGO RS Electrical Equipment Workshop Manual

80A-3
BATTERY
Battery: Removal - Refitting
80A
II - REMOVAL OF PART CONCERNED
1 - DISCONNECTING
a
aRemove the stud nut (2) from the negative battery
terminal.
aDisconnect the wiring (3) from the negative battery
terminal.a
aUndo the negative battery terminal nut (4) .
aRemove the negative battery terminal (5) .
119369
Note:
Before disconnecting the wiring of the negative
battery terminal, note the position of the wiring.
119371
Note:
Mark the position of the negative battery termi-
nal.

80A-4
BATTERY
Battery: Removal - Refitting
80A
2 - REMOVAL
a
aRemove the positive battery terminal wiring nut (6) .
aDisconnect the wiring (7) from the positive battery
terminal.a
aUndo the positive battery terminal nut (8) .
aRemove:
-the positive battery terminal (9) .
-the battery bracket bolt (10) ,
-the battery bracket (11) ,
-the battery (12) .
REFITTING
I - REFITTING PREPARATION OPERATION
aCheck the battery (see Battery: Check) (80A, Bat-
tery).
II - REFITTING OPERATION FOR PART
CONCERNED
1 - REFITTING
aPlace the battery in its housing, placing it as close to
the engine as possible.
aRefit:
-the battery bracket,
-the battery bracket bolt.
aTorque tighten the battery bracket bolt (12 N.m).
119370
Note:
Before disconnecting the positive battery ter mi-
nal wiring, mark the position of the wiring.
119371
Note:
Mar k the position of the positive battery ter minal.

80A-5
BATTERY
Battery: Removal - Refitting
80A
aPush the positive battery terminal fully onto the posi-
tive terminal post into the position marked during the
removal operation.
aTorque tighten the positive battery terminal nut (8
N.m).
aConnect the positive battery terminal wiring.
aTorque tighten the stud nut on the positive battery
terminal (12 N.m).
a
(see 80A, Battery, Battery: Precautions for the
repair, page 80A-1) .
2 - CONNECTION
a
aPush the negative battery terminal onto the negative
terminal post into the position marked during the re-
moval operation.
aTorque tighten the negative battery terminal nut (8
N.m).
aConnect the wiring to the negative battery terminal.
aTorque tighten the stud nut on the negative batte-
ry terminal (6 N.m).
(see 80A, Battery, Battery: Precautions for the
repair, page 80A-1) .
III - FINAL OPERATION
aRefit the battery cover.
aWhen refitting the battery or each time it is discon-
nected, carry out a certain number of operations, wi-
thout using the diagnostic tool, so that the vehicle
can operate correctly (see Battery: Initialisation)
(80A, Battery).WARNING
Poor contact may cause starting or charging
faults, create sparks and cause the battery to
explode.
WARNING
To prevent premature loosening of the stud nuts
on the negative terminal, refit a maximum of two
terminals per stud and distribute the terminals
over different studs.
WARNING
Poor contact may cause starting or charging
faults, create sparks and cause the battery to
explode.

80A-6
BATTERY
Battery tray: Removal - Refitting
80A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aRemove the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
II - OPERATION FOR REMOVAL OF PART
CONCERNED
aRemove the bolts (1) from the battery tray.
aTake out the battery tray (3) .
aUnclip the degassing pipe (2) from the battery tray.
aRemove the battery tray (3) .
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aClip the degassing pipe onto the battery tray.
aRefit:
-the battery tray,
-the battery tray bolts,aTorque tighten the battery tray bolts (21 N.m) in or-
der (4) , (5) , (6) .
II - FINAL OPERATION
aRefit the battery (see 80A, Battery, Battery: Remo-
val - Refitting, page 80A-2) . Tightening torquesm
battery tray bolts21 N.m
119372
119372

80B-1
HEADLIGHTS
Front lighting: List and location of components
80B
I - LIST OF COMPONENTS
II - LOCATION OF COMPONENTS
1 - Signalling light switch
To remove the signalling light switch (see 84A, Con-
trol - Signals, Signals and lighting switch: Removal
- Refitting, page 84A-8) .2 - UCH
The UCH is located in the dashboard, above the pas-
senger compartment relay/fuse box, for removal (see
87B, Passenger compartment connection unit,
UCH: Removal - Refitting, page 87B-1) .
3 - Passenger compartment fuse and relay box No. Description
(1) Signalling light switch
(2) UCH
(3) Passenger compartment fuse and relay
box
(4) Halogen headlight
(5) Fog light
(6) Side indicator
121133
119507
119504

80B-2
HEADLIGHTS
Front lighting: List and location of components
80B
4 - Halogen headlight
5 - Fog light6 - Side indicator
121210
121210
121205

80B-3
HEADLIGHTS
Halogen bulb: Removal - Refitting
80B
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSwitch off the ignition.
II - REMOVAL OPERATION FOR PART
CONCERNED
1 - Indicator bulb
aDisconnect the indicator connector.
aTurn the indicator bulb mounting a quarter of a turn
anti-clockwise (1) .
aRemove:
-the indicator "bulb mounting - bulb" assembly,
-the bulb from its mounting.2 - Side light bulbs
aRemove the cover (2) .
aDisconnect the side light connector.
aRemove:
-the "bulb mounting - bulb" assembly (3) from the
side light,
-the bulb from its mounting.
119377
119377
121386

80B-4
HEADLIGHTS
Halogen bulb: Removal - Refitting
80B
3 - Dipped beam headlight and main beam
headlight bulb
aRemove the cover (2) .
aDisconnect the dipped beam headlight and main
beam headlight connector.
aUndo the clip (4) at (5) .
aRemove the dipped beam headlight and main beam
headlight bulb (6) .REFITTING
REFITTING OPERATION FOR PART CONCERNED
1 - Indicator bulb
aRefit:
-a PY21W approved bulb on the indicator bulb
mounting,
-the "bulb mounting - bulb" assembly on the
halogen headlight.
aTurn the indicator bulb mounting a quarter of a turn
clockwise.
aConnect the indicator connector.
2 - Side light bulbs
aRefit:
-a W5W approved bulb on the side light bulb moun-
ting,
-the "bulb mounting - bulb" assembly on the
halogen headlight.
aConnect the side light connector.
aRefit the cover.
3 - Dipped beam headlight and main beam
headlight bulb
aRefit an H4 approved bulb on the halogen headlight.
aFit the clip onto the halogen headlight.
aConnect the dipped beam headlight and the main
beam headlight connector.
aRefit the cover.
119377
119378