2009 RENAULT TWINGO RS Electrical Equipment Workshop Manual

85A-3
WIPING - WASHING
Wiping and washing: List and location of components85A
8 - Windscreen wiper jet
9 - Rear screen wiper blade10 - Rear screen wiper blade arm
11 - Rear screen wiper motor
The rear screen wiper motor is located under the tail-
gate trim.
119382
119527
119520
119425

85A-4
WIPING - WASHING
Wiping and washing: List and location of components85A
12 - Rear screen washer jet
13 - Windscreen washer bottle14 - Windscreen washer pump
15 - Rain and light sensor
The rain and light sensor is located under the interior
rear-view mirror covers.
119532
121090121089
101715

85A-5
WIPING - WASHING
Windscreen wiper blade: Removal - Refitting
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
aSwitch off the ignition.
II - REMOVAL OPERATION FOR PART
CONCERNED
aPress on the windscreen wiper blade clip (1) .
aExtract the windscreen wiper blade from the winds-
creen wiper arm at (2) .
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aRefit the windscreen wiper blade onto the winds-
creen wiper arm.
119383

85A-6
WIPING - WASHING
Windscreen wiper arm: Removal - Refitting
LEFT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aVisually mark the position of the wiper arms (1) .II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the nut covers (2) .
aRemove nuts (3) .
aRemove the windscreen wiper arms (4) using the
(Ele. 1294-01) (5) . Special tooling required
Ele. 1294-01Tool for removing wiper arms.
Tightening torquesm
wiper arm nuts21 Nm
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119382
119385
119386
119387

85A-7
WIPING - WASHING
Windscreen wiper arm: Removal - Refitting
LEFT-HAND DRIVE
85A
REFITTING
REFITTING OPERATION FOR PART CONCERNED
aFit the windscreen wiper arms in the position marked
before the removal operation (1) .
aRefit the wiper arm nuts.
aTorque tighten the wiper arm nuts (21 Nm).
aRefit the wiper arm nut covers.
119382

85A-8
WIPING - WASHING
Windscreen wiper arm: Removal - Refitting
RIGHT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aVisually mark the position of the wiper arms (1) .II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove the nut covers (2) .
aRemove nuts (3) .
aRemove the windscreen wiper arms (4) using the
(Ele. 1294-01) (5) . Special tooling required
Ele. 1294-01Tool for removing wiper arms.
Tightening torquesm
wiper arm nuts21 Nm
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119382
125228
125229
125230

85A-9
WIPING - WASHING
Windscreen wiper arm: Removal - Refitting
RIGHT-HAND DRIVE
85A
REFITTING
REFITTING OPERATION FOR PART CONCERNED
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aFit the windscreen wiper arms in the position marked
before the removal operation (1) .
aRefit the wiper arm nuts.
aTorque tighten the wiper arm nuts (21 Nm).
aRefit the wiper arm nut covers.WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119382

85A-10
WIPING - WASHING
Windscreen wiper mechanism: Removal - Refitting
LEFT-HAND DRIVE
85A
REMOVAL
I - REMOVAL PREPARATION OPERATION
a
aSwitch on the ignition.
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aSwitch off the ignition.
aDisconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, page 80A-2) .
aRemove:
-the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) ,
-the scuttle panel grille (see Scuttle panel grille:
Removal - Refitting) (MR 412, 56A, Exterior equi-
pment).
II - REMOVAL OPERATION FOR PART
CONCERNED
aRemove:
-the front windscreen wiper mechanism bolts (1) ,
-the windscreen wiper mechanism.
aDisconnect the windscreen wiper motor connector.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
aConnect the windscreen wiper motor connector.
aRefit:
-the windscreen wiper mechanism,
-the windscreen wiper mechanism bolts.
II - FINAL OPERATION.
aRefit the scuttle panel grille (see Scuttle panel
grille: Removal - Refitting) (MR 412, 56A, Exterior
equipment).
aConnect the battery (see 80A, Battery, Battery: Re-
moval - Refitting, page 80A-2) .
aMove the wiper stalk from (0) to (1), then from (1) to
(0).
aRefit the windscreen wiper arms (see 85A, Wiping -
Washing, Windscreen wiper arm: Removal - Re-
fitting, page 85A-6) . WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.
119389
WARNING
To ensure that the wiper arms can travel
smoothly, the wiper motor must be initialised.