88A-19
WIRING HARNESS
Engine wiring: Removal - Refitting
K9K
88A
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
aRemove the engine harness.
REFITTING
I - REFITTING PREPARATIONS OPERATION
aIf replacing with a complete wiring harness, lock the
unused connectors (see Connectors: Sealing and
locking) (Technical Note 6015A, 88A, Wiring).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the engine harness.
aConnect the engine cooling fan assembly connector.
aConnect:
-the air conditioning compressor connector,
-the refrigerant fluid pressure sensor connector,
-the engine cooling fan assembly resistor connec-
tor,
-the engine cooling fan assembly connector.
aConnect:
-the engine harness/front of engine wiring connec-
tor,
-the reversing lights switch connector,
-the crankshaft position sensor connector,
-the coolant temperature sensor connector,
-the air inlet temperature sensor connector,-the exhaust gas recirculation solenoid valve con-
nector,
-the connector to the pre-postheating unit,
-the diesel injection computer connectors,
-the fuel rail pressure sensor connector,
-the fuel temperature sensor connector,
-the heater plugs connector,
-the injector connectors,
-the air temperature sensor connector,
-the turbocharging pressure sensor connector,
-the pinking sensor connector,
-the camshaft position sensor connector,
-the connector from the water detection sensor on
the fuel filter,
-the alternator connector,
-the oil pressure sensor connector.
aRefit:
-the engine compartment connection unit supply wi-
ring nut,
-the wiring mounting nut on the battery protection
fuse board,
-the battery protection fuse wiring nuts,
-the earth wiring nut on the front left-hand side
member,
-the positive battery terminal wiring nut,
-the engine earth wiring nut,
-the starter supply and earth terminal nuts,
-the alternator earth wiring nut.
aClip:
-the section of wiring on the cylinder head,
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
III - FINAL OPERATION.
aRefit:
-the battery tray (see 80A, Battery, Battery tray:
Removal - Refitting, page 80A-6) ,
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture), WARNING
To prevent any damage during the removal ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
STANDARD HEATING
AIR CONDITIONING
88A-24
WIRING HARNESS
Engine wiring: Removal - Refitting
D4F, and 780
88A
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
aRemove the engine harness.
REFITTING
I - REFITTING PREPARATION OPERATION
aIf replacing with a complete wiring harness, lock the
unused connectors (see Connectors: Sealing and
locking) (Technical Note 6015A, 88A, Wiring).
II - REFITTING OPERATION FOR PART
CONCERNED
aRefit the engine harness.
aConnect the engine cooling fan assembly connector.
aConnect:
-the air conditioning compressor connector,
-the refrigerant fluid pressure sensor connector,
-the engine cooling fan assembly connector,
-the engine cooling fan assembly resistor connec-
tor.
aConnect:
-the engine harness/front of engine wiring connec-
tor,
-the connectors to the petrol injection computer,
-the reversing lights switch connector,
-the downstream oxygen sensor connector,
-the turbocharger solenoid valve connector,-the ignition coil connector,
-the motorised throttle valve connector,
-the turbocharger pressure sensor connector,
-the air temperature sensor connector,
-the pinking sensor connector,
-the alternator connector,
-the oil pressure sensor connector,
-the crankshaft position sensor connector,
-the coolant temperature sensor connector,
-the engine harness/injection wiring connector,
-the oil vapour recirculation hose reheater connec-
tor,
-the air inlet pressure sensor connector,
-upstream oxygen sensor connector,
-the fuel vapour absorber connector.
aRefit:
-the engine compartment connection unit supply
terminal nut,
-the wiring mounting nut on the battery protection
fuse board,
-the negative battery terminal wiring nuts,
-the positive battery terminal wiring nut,
-the earth wiring nut on the front left-hand side
member,
-the earth wiring nuts on the engine,
-the starter wiring nuts,
-the alternator earth wiring nut.
aClip:
-the section of wiring on the cylinder head,
-the section of wiring on the cylinder block and sub-
frame,
-the section of wiring on the engine cooling fan as-
sembly.
III - FINAL OPERATION.
aRefit:
-the battery tray (see 80A, Battery, Battery tray:
Removal - Refitting, page 80A-6) ,
-the air filter unit (see Air filter unit: Removal - Re-
fitting) (MR 411, 12A, Fuel mixture),
-the battery (see 80A, Battery, Battery: Removal -
Refitting, page 80A-2) , WARNING
To prevent any damage during the removal ope-
ration, check that the wiring is free from its moun-
tings (retaining clip, plastic clip, adhesive tape,
connector, etc.).
STANDARD HEATING
AIR CONDITIONING
