2006 LAND ROVER FRELANDER 2 lock

DT CDescriptionPossible CauseAction
s t uck clos ed
P0088-22Fuel Rail /Sys tem Pres s ure -Too High• NO TE: - Ci rcuit I_A_RALPS -
Leaki ng fuel s yst emVolume cont rol valvecircui t s hort ci rcuit t oground, open ci rcuitVolume cont rol valve s tuckopen
Check for fuel leaksRefer to the el ect ri cal circui t diagramsand check volume control val ve ci rcuitfor s hort circui t to ground, open circui tCheck and i ns t all a new hi gh pres s urefuel pump as requi red. Refer to thewarrant y poli cy and procedures manual,or det ermi ne if any prior approvalprogramme is in operat ion, pri or t o t heins tal lati on of a new modul e/component
P0088-24Fuel Rail /Sys tem Pres s ure -Too High - Si gnal s t uck hi ghLeaki ng fuel s yst emPres s ure control val ves t uckPres s ure control val vecircui t s hort ci rcuit t oground, s hort circuit t opower, open circui t
Check for fuel leaksRefer to the el ect ri cal circui t diagramsand check pres s ure control valve ci rcuitfor s hort circui t to ground, s hort circui tto power, open ci rcuitCheck and i ns t all new pres s ure controlval ve as required. Refer to t he warrantypol icy and procedures manual, ordet ermine i f any prior approvalprogramme is in operat ion, pri or t o t heins tal lati on of a new modul e/component
P0088-27Fuel Rail /Sys tem Pres s ure -Too High - Si gnal rate ofchange above threshold
Leak in hi gh pres s ures ect ionInjector nozzl e s tuckopen/wornW orn hi gh pres sure pump,fil ter blockedLeaki ng pres s ure controlvalveLow press ure sect ionpres s ure low (leak i ns yst em, pump out put l ow)
Check for fuel leaks in hi gh and lowpres sure s yst emsUsi ng t he manufacturer approveddiagnos t ic s yst em, check for relat edDTCs and refer t o t he rel evant DTCindex
P0089-62Fuel Pres s ure Regulat orPerformance - Signal comparefai lure
Fuel low press ure del iverys yst emFuel press ure cont rol valveexceeded t olerancet hres hol d
Check fuel l ow pres s ure del ivery s ys temCheck and i ns t all a new fuel pres surecont rol val ve as required. Refer to thewarrant y poli cy and procedures manual,or det ermi ne if any prior approvalprogramme is in operat ion, pri or t o t heins tal lati on of a new modul e/component
P0089-64Fuel Pres s ure Regulat orPerformance - Signalplaus ibil it y fai lure
Fuel low press ure del iverys yst emFuel press ure cont rol valveexceeded t olerancet hres hol d
Check fuel l ow pres s ure del ivery s ys temCheck and i ns t all a new fuel pres surecont rol val ve as required. Refer to thewarrant y poli cy and procedures manual,or det ermi ne if any prior approvalprogramme is in operat ion, pri or t o t heins tal lati on of a new modul e/component
P0097-00Int ake Air Temperat ureSens or 2 Ci rcuit Low - No s ubt ype i nformati on
• NO TE: - Ci rcuit I_A_IATS -
Intake air t emperat ures ensor s hort circui t toground
Refer to the el ect ri cal circui t diagramsand check int ake air t emperature s ens orfor s hort circui t to groundCarry out t he pinpoint t est s as s oci at edwit h t his DTC us ing the manufact urerapproved di agnos ti c s ys t em
P0098-00Int ake Air Temperat ureSens or 2 Ci rcuit Hi gh - No s ubt ype i nformati on
• NO TE: - Ci rcuit I_A_IATS -
Intake air t emperat ures ensor s hort circui t topower
Refer to the el ect ri cal circui t diagramsand check int ake air t emperature s ens orfor s hort circui t to powerCarry out t he pinpoint t est s as s oci at edwit h t his DTC us ing the manufact urerapproved di agnos ti c s ys t em
P009B-00Fuel Pres s ure Rel ief ControlCircui t/Open - No s ub t ypeinformat ion
• NO TE: - Ci rcuit O_T_PCV -
Pres s ure control val vecontrol circui t open ci rcuit
Refer to the el ect ri cal circui t diagramsand check pres s ure control valve ci rcuitfor open circuitCarry out t he pinpoint t est s as s oci at edwit h t his DTC us ing the manufact urerapproved di agnos ti c s ys t em
P009C-00Fuel Pres s ure Rel ief ControlCircui t Low - No s ub t ypeinformat ion
• NO TE: - Ci rcuit O_T_PCV -
Pres s ure control val vecontrol circui t s hort circuitt o ground
Refer to the el ect ri cal circui t diagramsand check pres s ure control valve ci rcuitfor s hort circui t to groundCarry out t he pinpoint t est s as s oci at edwit h t his DTC us ing the manufact urerapproved di agnos ti c s ys t em

DT CDescriptionPossible CauseAction
U0101-00Lost communicat ionwit h TCM - No s ubt ype i nformati on
Los t communi cat ion wi tht he Trans mis s ionControl Modul eCAN net work fault
Check t he Trans mis s ion Cont rol Module for st ored DTCs .Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Trans mis s ion Cont rol Modul eU0121-00Lost communicat ionwit h Ant i-lock BrakeSyst em (ABS)Control Module - Nos ub type i nformati on
Los t communi cat ion wi tht he Anti -l ock BrakeSys tem Modul eCAN net work fault
Check t he Anti -l ock Brake Sys t em Module for s tored DTCs.Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Anti -l ock Brake Sys t em ModuleU0126-00Lost communicat ionwit h St eering Angl eSens or Module - Nos ub type i nformati on
Los t communi cat ion wi tht he Steering AngleSensor ModuleCAN net work fault
Check t he Steering Angle Sens or Modul e for s t ored DTCs .Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Steeri ng Angle Sens or Module
U0140-00Lost communicat ionwit h Body ControlModule - No subt ype i nformati on
Los t communi cat ion wi tht he Central Junct ion BoxCAN net work fault
Check t he Central Junct ion Box for s tored DTCs . Us ing themanufacturer approved diagnost ic sys tem, complet e t heCAN Net work Integri ty tes t. Refer t o t he electrical ci rcuitdiagrams and check the CAN network bet ween t he Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e and t he CentralJuncti on Box
U0300-00Int ernal Cont rolModule Soft wareIncompati bili ty - Nos ub type i nformati on
Car Configurat ion Fi le(CCF) i nformati oni ncompati ble t o t heAdapti ve Front Li ghti ngSys tem (AFS) Cont rolModule
• NOTE: The Car Configurat ion Fil e (CCF) parametersrequired are (Vehicle type)(Headl amp t ype)(Gearbox t ype)and (Dayrunning light )
Re-configure the Car Confi gurati on Fil e (CCF) as requi redusi ng t he manufact urer approved diagnost ic s ys tem. Cl earDTC and re-t es t . If t he DTC remains s us pect t he Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e, refer t o t henew module ins tall ati on not e at t he t op of the DTC IndexU0402-00Invali d Dat aRecei ved FromTrans mis s ion Cont rolModule - No subt ype i nformati on
Inval id Dat a Recei vedfrom the Transmis si onControl Modul eTrans mi ss i on componentfaul t
Check t he Trans mis s ion Cont rol Module for st ored DTCs .Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Trans mis s ion Cont rol Modul eU0415-00Invali d Dat aRecei ved FromAnti -Lock BrakeSyst em (ABS)Control Module - Nos ub type i nformati on
Inval id dat a receivedfrom Anti -l ock BrakeSys tem Modul eAnt i-lock Brake Syst emModule component fault
Check t he Anti -l ock Brake Sys t em Module for s tored DTCs.Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Anti -l ock Brake Sys t em Module
U0422-00Invali d data fromBody Cont rol Module- No s ub t ypeinformat ion
Inval id s i gnal from theCentral Juncti on BoxCentral Juncti on Boxfaul t
Check t he Central Junct ion Box for s tored DTCs . Us ing themanufacturer approved diagnost ic sys tem, complet e t heCAN Net work Integri ty tes t. Refer t o t he electrical ci rcuitdiagrams and check the CAN network bet ween t he Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e and t he CentralJuncti on Box
U0428-00Invali d Dat aRecei ved FromSteering AngleSens or Module - Nos ub type i nformati on
Inval id Dat a Recei vedfrom the St eeri ng Angl eSensor ModuleSt eering Angle Sens orModule fault
Check t he Steering Angle Sens or Modul e for s t ored DTCs .Us ing t he manufacturer approved diagnost ic sys tem,compl ete the CAN Net work Int egrit y t est . Refer t o theelectrical ci rcuit diagrams and check t he CAN networkbet ween t he Adapt ive Front Li ght ing Sys tem (AFS) ControlModul e and t he Steeri ng Angle Sens or
U2100-00Ini ti al Configurat ionNot Complet e - Nos ub type i nformati on
Car Configurat ion Fi le(CCF) i nformati on notreceived complet ely
• NOTE: The Car Configurat ion Fil e (CCF) parametersrequired are (Vehicle type)(Headl amp t ype)(Gearbox t ype)and (Dayrunning light )
Re-configure the Car Confi gurati on Fil e (CCF) as requi redusi ng t he manufact urer approved diagnost ic s ys tem. Cl earDTC and re-t es t . If t he DTC remains s us pect t he Adapt iveFront Lighti ng Sys t em (AFS) Cont rol Modul e, refer t o t henew module ins tall ati on not e at t he t op of the DTC IndexU2101-00Control ModuleConfigurat ionIncompati ble - Nos ub type i nformati on
Car Configurat ion Fi le(CCF) i nformati oni ncompati ble t oAdapti ve Front Li ghti ngSys tem (AFS) Cont rolModule
Check t he correct Adapti ve Front Li ght ing Sys t em (AFS)Cont rol Module is i ns t alled to vehicle s pecificati on. Refitori gi nal or repl ace the modul e as required. Refer to thenew module/component ins tall ati on note at t he t op of theDTC Index
U3003-16Batt ery Vol tage -Circui t vol tage belowt hreshol d
The power s upply to theModule has been below9 Vol ts for more than1000 mi ll is econds
Sus pect Bat t ery or Charging fault . Check t he batt erycondit ion and st ate of charge. Check t he vehicle chargi ngs ys t em. Refer to the relevant workshop manual s ect ion.Clear the DTC, cycl e i gni ti on s tat e to off t hen on, i f DTCret urns refer to the el ect ri cal circui t diagrams and checkpower and ground ci rcuit t o t he Adapt ive Front Light ingSys t em (AFS) Cont rol Modul e

Publi s hed: 03-May-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC:
Instrument Cluster (IPC)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the ins trument cl us t er sys tem, refer t o t he rel evant Descripti on and Operat ion s ecti on in t heworks hop manual .For addit ional informat ion, refer t o: Ins t rument Clus ter (413-01 Inst rument Cl us t er, Des cript ion and Operat ion).
Instrument cluster control module (IPC )DT CDescriptionPossible CauseAction
B1184-62Steering Column LockOutputSignal compare fai lureCheck st eering lock power from CJB. Check CJB forDTCs and refer to relevant DTC Index.For addi ti onal informat ion, refer t o:Communicati ons Network (418-00 Modul eCommunicati ons Network, Di agnos is and Tes t ing).
B1A14-96RCM W arning LampLight Emit t ing Di ode (LED)fai lureIns t all a new ins trument cl us t er.For addi ti onal informat ion, refer t o: Ins t rumentClus t er (413-01 Inst rument Cl us t er, Removal andIns t allat ion).Refer t o t he new module/component ins tall ati onnote at the t op of the DTC Index
B1A84-41Car Configurat ion Dat aFlas h download checks umerrorIns t all lat est avail abl e l evel of software us ing t hemanufacturer approved di agnos ti c s ys t em
B1A84-81Car Configurat ion Dat aInvali d Car Configurat iondata recei vedCheck/amend Car Configurat ion Fil e us ingmanufacturer approved di agnos ti c s ys t em
C2002-62Odometer TamperedDTC s et when one or mores tored odomet er val ue doesnot match
Clear DTC, cycle ignit ion and re-t est
U0010-87Medium Speed CANCommunicati on BusMult ipl e los s of CAN dat a toother s yst emsCarry out pinpoint tes t s ass ociat ed wit h t his DTCus ing t he manufacturer approved diagnos ti cs yst em
U0010-88Medium Speed CANCommunicati on BusBreak i n connecti on to busCarry out pinpoint tes t s ass ociat ed wit h t his DTCus ing t he manufacturer approved diagnos ti cs yst emU0140-08Lost Communi cat ionW i th Body Cont rolModule
No mes s ages recei ved fromCJB for great er than t imeoutperi od
Carry out pinpoint tes t s ass ociat ed wit h t his DTCus ing t he manufacturer approved diagnos ti cs yst em
U0208-08Lost Communi cat ionW i th "Seat Cont rolModule A"
No mes s ages recei ved fromDSM for greater t hant imeout period
Check DSM for DTCs and refer t o rel evant DTCIndex.For addi ti onal informat ion, refer t o: Seat s (501-10Seati ng, Di agnos is and Tes ti ng).Carry out CAN Net work i nt egri ty t es ts us ing themanufacturer approved di agnos ti c s ys t emU0300-62Int ernal Cont rol ModuleSoft ware Incompat ibi lit yConfigurat ion dat a receivedis di fferent from the s t oreddata
Check correct ins trument cl us t er is i nst all ed
U3000-46Control ModuleEEPROM writ e errorCheck power and ground circui ts to the i nst rumentclus ter, cl ear DTC and re-tes t. If DTC remains ,ins t al l a new i nst rument clus t er.For addi ti onal informat ion, refer t o: Ins t rumentClus t er (413-01 Inst rument Cl us t er, Removal andIns t allat ion).Refer t o t he new module/component ins tall ati onnote at the t op of the DTC Index

Publ is hed: 21-Oct -2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Occupant
Classification System (OCS)
Des cript ion and Operat ion
CAUTION: W hen probing connectors t o take meas urement s in the cours e of t he pinpoint t es t s , us e t he adaptor kit ,part number 3548-1358-00.
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the occupant clas s ifi cat ion sys tem, refer t o t he rel evant Descripti on and Operat ion s ecti on int he works hop manual . For addit ional informati on, refer t o: Ai r Bag and Safet y Belt Pret ens i oner Suppl emental Rest rai ntSyst em (SRS) (501-20B Supplement al Res traint Syst em, Des cript ion and Operat ion).
Occupant C lassification System (OC S)
DT CDescriptionPossible CauseActionB1193-53Cras h EventStorage Ful l andLocked -deact ivated
Cras h event occurredClear diagnos t ic t rouble code and re-t est
B1A54-01Occupant BeltTens i on Sens or -General Elect ricalFailure
General electricalfailureClear diagnos t ic t rouble code and re-t est . If theproblem pers is t s, check and ins tall a new s afety bel ttens ion s ens or as required. Refer t o t he warrant ypolicy and procedures manual, or determine i f anypri or approval programme is in operat ion, pri or t o t heins tal lat ion of a new modul e/component
B1A54-02Occupant BeltTens i on Sens or -General si gnalfai lure
General s ignal fail ureRefer t o the el ect ri cal circui t diagrams and checks afety bel t tens ion and mat press ure s ens or circuit sfor s hort t o each other
B1A54-11Occupant BeltTens i on Sens or -circuit short toground
Safet y belt t ens i ons ensor volt agereference or s ignalcircui t - s hort to ground
Refer t o the el ect ri cal circui t diagrams and checks afety bel t tens ion s ens or volt age reference ands ignal ci rcuit s for s hort t o ground
B1A54-12Occupant BeltTens i on Sens or -circuit short tobatt ery
Safet y belt t ens i ons ensor volt agereference or s ignalcircui t - s hort to power
Refer t o the el ect ri cal circui t diagrams and checks afety bel t tens ion s ens or volt age reference ands ignal ci rcuit s for s hort t o power
B1A54-13Occupant BeltTens i on Sens or -circuit open
Safet y belt t ens i ons ensor volt agereference or s ignalcircui t - open ci rcuit
Refer t o the el ect ri cal circui t diagrams and checks afety bel t tens ion s ens or volt age reference ands ignal ci rcuit s for open circuit
B1A62-02Pres s ure Sens or -General si gnalfai lure
General s ignal fail ureRefer t o the el ect ri cal circui t diagrams and checks afety bel t tens ion and mat press ure s ens or circuit sfor s hort t o each other
B1A62-11Pres s ure Sens or -circuit short toground
Mat pres s ure sens orvolt age reference ors ignal ci rcuit s - s hort t oground
Refer t o the el ect ri cal circui t diagrams and check matpres s ure s ensor volt age reference and si gnal circui tsfor s hort t o ground
B1A62-12Pres s ure Sens or -circuit short tobatt ery
Mat pres s ure sens orvolt age reference,ground or s ignal ci rcuit s- s hort t o power
Refer t o the el ect ri cal circui t diagrams and check matpres s ure s ensor volt age reference, ground and s ignalcircuit s for short to power

DT CDescriptionPossible CauseAction
U0100-00Lost Communi cat ion W it hECM/PCM "A" - no sub t ypeinformat ion
Los t communi cat ionwi th Engi ne Cont rolModule (ECM)
Refer to t he elect rical circuit di agrams andcheck the power and ground circui ts to t heEngine Cont rol Module (ECM). Us ing themanufact urer approved diagnos t ic s yst em,complet e a CAN network int egrit y t es t . Refert o t he electrical ci rcuit di agrams and checkt he CAN net work bet ween the Al l Terrai nCont rol Modul e (ATCM) and Different ialEl ect ronic Modul e (DEM).
U0121-00Lost Communi cat ion W it hAnti -Lock Brake Syst em(ABS) Control Modul e - nos ub type i nformati on
Los t communi cat ionwi th Ant i-Lock BrakeSys tem (ABS) module
Refer to t he elect rical circuit di agrams andcheck the power and ground circui ts to t heAnt i-Lock Brake Sys t em (ABS) modul e. Us i ngt he manufact urer approved di agnos ti cs ys tem, complet e a CAN net work int egrit yt es t. Refer t o t he electrical ci rcuit diagramsand check the CAN net work bet ween t he AllTerrain Cont rol Module (ATCM) andDi fferenti al El ect roni c Modul e (DEM).
U0138-00Lost Communi cat ion wi th AllTerrai n Control Modul e - nos ub type i nformati on
Los t communi cat ionwi th All Terrai n ControlModule (ATCM)
Refer to t he elect rical circuit di agrams andcheck the power and ground circui ts to t heAl l Terrai n Control Module (ATCM). Usi ng t hemanufact urer approved diagnos t ic s yst em,complet e a CAN network int egrit y t es t . Refert o t he electrical ci rcuit di agrams and checkt he CAN net work bet ween the Al l Terrai nCont rol Modul e (ATCM) and Different ialEl ect ronic Modul e (DEM).
U0140-00Lost Communi cat ion W it hBody Cont rol Module - nos ub type i nformati on
Los t communi cat ionwi th Cent ral Junct ionBox (CJB)
Refer to t he elect rical circuit di agrams andcheck the power and ground circui ts to t heCent ral Juncti on Box (CJB). Usi ng themanufact urer approved diagnos t ic s yst em,complet e a CAN network int egrit y t es t . Refert o t he electrical ci rcuit di agrams and checkt he CAN net work bet ween the Cent ralJunct ion Box (CJB) and Different ial Electroni cModule (DEM).
U0300-00Int ernal Cont rol ModuleSoft ware Incompat ibi lit y - nos ub type i nformati on
Hi gh s peed CANcommunicati on buscircui t problemInval id confi gurati onmes s age is recei ved
Us i ng the manufact urer approved diagnos t ics ys tem, complet e a CAN net work int egrit yt es t. Refer t o t he electrical ci rcuit diagramsand check the CAN net work to theDi fferenti al El ect roni c Modul e (DEM).Refer to t he elect rical circuit di agrams andcheck the power and ground circui ts to t hemodul e. Us i ng the manufact urer approveddi agnos ti c s ys t em, compl ete a CAN net worki ntegri ty tes t. Refer to t he elect rical circuitdi agrams and check t he CAN net workbet ween the Cent ral Juncti on Box (CJB) andDi fferenti al El ect roni c Modul e (DEM). Cleart he DTC and re-t es t.
U0300-4AInt ernal Cont rol ModuleSoft ware Incompat ibi lit y -incorrect componentins t al led
Di fferenti al El ect ronicModule (DEM) mi s si ngcali brati on, corrupts oft wareIncorrect Different ialElect ronic Module(DEM) ins tal led t ovehicle
Us i ng the manufact urer approved diagnos t ics ys tem check and i ns t all lat est relevant l evelof s oft ware to the Di fferenti al El ect ronicModule (DEM). Clear the DTC and re-tes t .Check and ensure t he correct Different ialEl ect ronic Modul e (DEM) i s i ns t alled. Checkand i nst all a new Different ial Electroni cModule (DEM) as requi red. Refer t o t heW arrant y Poli cy and Procedures manual , ordet ermi ne if any prior approval programme i si n operat ion, prior t o t he ins t al lat ion of anew modul e/component .
U0401-68Invali d Dat a Recei ved FromECM/PCM - event i nformat ionInval id dat a receivedCheck Engi ne Control Module (ECM) forrelat ed DTCs and refer t o t he rel evant DTCIndex. Cl ear t he DTC and re-t est .
U0415-00Invali d Dat a Recei ved FromAnti -Lock Brake Syst em(ABS) Control Modul e - nos ub type i nformati on
Inval id dat a receivedfrom Anti -Lock BrakingSys tem (ABS) module
Check Anti Lock Braking Sys tem (ABS)modul e for related DTCs and refer t o t herelevant DTC Index. Clear the DTC andre-t es t.
U0418-68Invali d Dat a Recei ved FromBrake Sys tem Cont rol Module- event i nformati on
Inval id dat a receivedfrom Anti -Lock BrakingSys tem (ABS) module
Check Anti Lock Braking Sys tem (ABS)modul e for related DTCs and refer t o t herelevant DTC Index. Clear the DTC andre-t es t.

DT C
Description Possible Cause Action
B1128-1A Dri vers Side-Side Inflat able
Curt ain Deployment Control -
Circui t res is t ance below
t hreshol d Driver's s ide curt ain ai r
bag ci rcuit res i st ance
bel ow t hres hol d Refer to el ect ri cal circui t diagrams and
driver's s ide curt ain ai r bag ci rcuit for
short ci rcuit between bot h l ines to s ide
curtain air bag B1128-95
Dri vers Side-Side Inflat able
Curt ain Deployment Control -
Incorrect as s embly Driver’s s ide curt ain ai r
bag incorrect ass embl y Check dri ver’s si de curtai n air bag
ins tall ed correct ly Usi ng t he manufact urer approved
di agnos t ic s yst em check and up-date the
car configurat ion fil e as requi red B1129-11
Pass engers Side-Side
Inflat abl e Curt ain
Deployment Cont rol - Circui t
s hort t o ground Pas s enger's s ide curt ain
ai r bag ci rcuit s hort circui t
to ground Refer to the el ect ri cal circui t di agrams
and check pass enger's s i de curtai n air
bag ci rcuit for short ci rcuit t o ground B1129-12
Pass engers Side-Side
Inflat abl e Curt ain
Deployment Cont rol - Circui t
s hort t o batt ery Pas s enger's s ide curt ain
ai r bag ci rcuit s hort circui t
to power Refer to the el ect ri cal circui t di agrams
and check pass enger's s i de curtai n air
bag ci rcuit for short ci rcuit t o power B1129-13
Pass engers Side-Side
Inflat abl e Curt ain
Deployment Cont rol - Circui t
open Pas s enger's s ide curt ain
ai r bag ci rcuit open circui t Refer to the el ect ri cal circui t di agrams
and check pass enger's s i de curtai n air
bag ci rcuit for open circui t B1129-19
Pass engers Side-Side
Inflat abl e Curt ain
Deployment Cont rol - Circui t
current above threshold Pas s enger's s ide curt ain
ai r bag ci rcuit current
above t hres hol d Refer to el ect ri cal circui t diagrams and
check pass enger’s s i de curtai n air bag
ci rcuit for swapped pins or cros s coupl ing
bet ween t wo fi ri ng li nes B1129-1A
Pass engers Side-Side
Inflat abl e Curt ain
Deployment Cont rol - Circui t
res is t ance bel ow t hreshol d Pas s enger's s ide curt ain
ai r bag ci rcuit resi s tance
bel ow t hres hol d Refer to el ect ri cal circui t diagrams and
pas s enger's s ide curtain air bag circuit for
short ci rcuit between bot h l ines to s ide
curtain air bag B1129-95
Pass engers Side-Side
Inflat abl e Curt ain
Deployment Cont rol -
Incorrect as s embly Pas s enger’s s ide curt ain
ai r bag incorrect as sembl y Check pas senger’s si de curt ai n air bag
ins tall ed correct ly Usi ng t he manufact urer approved
di agnos t ic s yst em check and up-date the
car configurat ion fil e as requi red B1193-68
Cras h Event St orage Full and
Locked - Event informati on Res t raint s cont rol module
crash event s torage area
full and l ocked Read out t he event dat a recorder and
then refer to the warrant y policy and
procedures manual , or det ermi ne if any
prior approval programme is i n operat ion,
prior t o t he ins tal lat ion of a new modul e B1194-11
Dri ver Si de Frontal
Accelerati on Sens or - Circui t
s hort t o ground Driver's s ide front i mpact
sens or ci rcuit s hort circui t
to ground Refer to the el ect ri cal circui t di agrams
and check dri ver's s ide front i mpact
sens or ci rcuit for short ci rcuit t o ground B1194-12
Dri ver Si de Frontal
Accelerati on Sens or - Circui t
s hort t o batt ery Driver's s ide front i mpact
sens or ci rcuit s hort circui t
to power Refer to the el ect ri cal circui t di agrams
and check dri ver's s ide front i mpact
sens or ci rcuit for short ci rcuit t o power B1194-19
Dri ver Si de Frontal
Accelerati on Sens or - Circui t
current above threshold Driver's s ide front i mpact
sens or ci rcuit current
above t hres hol d Refer to el ect ri cal circui t diagrams and
driver’s s ide front i mpact s ensor circui t for
swapped pins or cros s coupl ing bet ween
two fi ring lines B1194-4A
Dri ver Si de Frontal
Accelerati on Sens or -
Incorrect component i nst all ed Driver's s ide front i mpact
sens or incorrect
component ins tall ed Res t raint s cont rol module det ected a
mis s -mat ch between t he hardware fi tt ed
and what i s expect ed Check correct driver’s si de front impact
sens or ins tall ed B1194-87
Dri ver Si de Frontal
Accelerati on Sens or - Mis s ing
mes s age Driver's s ide front i mpact
sens or ci rcuit open circuit Driver's s ide front i mpact
sens or internal faul t Refer to el ect ri cal circui t diagrams and
driver's s ide front i mpact s ensor for
communi cat ion fault B1194-95
Dri ver Si de Frontal
Accelerati on Sens or -
Incorrect as s embly Driver’s s ide front i mpact
sens or incorrect ass embl y Check dri ver’s si de front impact sens or
ins tall ed correct ly Usi ng t he manufact urer approved
di agnos t ic s yst em check and up-date the
car configurat ion fil e as requi red B1194-96
Dri ver Si de Frontal
Accelerati on Sens or -
Component i nt ernal fai lure Driver's s ide front i mpact
sens or internal faul t Refer to el ect ri cal circui t diagrams and
check dri ver's s ide front i mpact s ens or B1195-11
Pass enger Si de Frontal
Accelerati on Sens or - Circui t
s hort t o ground Pas s enger's s ide front
impact sens or ci rcuit
short ci rcuit t o ground Refer to the el ect ri cal circui t di agrams
and check pass enger's s i de front impact
sens or ci rcuit for short ci rcuit t o ground

Publ is hed: 27-Apr-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Steering
Angle Sensor Module (SASM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under manufacturer warrant y, refer t o t heW arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or approval program is i n operat ion, beforet he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t codes . Match t he 5 digi ts from t he s cant ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the last 2 digi ts gi ve ext ra informati on read by themanufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci malplaces, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al ways take t he res is t ance of t he DMMleads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi ng pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or corros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is not present , an int ermi tt ent concern maybe t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the ant i lock cont rol s tabil it y s yst em, refer to the relevant Des cri pt ion and Operati on s ect ionin the workshop manual.For addit ional informat ion, refer t o: Anti -Lock Cont rol - St abi li ty As s is t (206-09C Anti -Lock Cont rol - St abi lit y As s is t,Des cript ion and Operat ion).
Steering Angle Sensor Module
DT CDescriptionPossible CauseAction
U0001-00High Speed CANCommunicati on BusGeneral Fai lureInformat ion No s ub typeinformat ion
Bus OffCarry out t he pinpoint t es t s as sociat ed to thi s DTCus ing the manufact urer approved di agnos ti c s yst em
U0140-00Lost Communi cat ion W it hCentral el ect ronic modul eGeneral Fai lureInformat ion No s ub typeinformat ion
Lost communicat ion wi thCJBCarry out t he pinpoint t es t s as sociat ed to thi s DTCus ing the manufact urer approved di agnos ti c s yst em
U0300-00Int ernal Control ModuleSoft ware Incompat ibi lit yGeneral Fai lureInformat ion No s ub typeinformat ion
CAN Bus faul tLoss of power t o moduleIncorrect componentins t al ledModule i nternal fai lure
Carry out CAN net work and power feed t es ts us ingmanufact urer approved di agnos t ic s yst em. Checkcorrect s t eering wheel rot ati on s ens or is ins tall ed.Ins tall a new s teeri ng wheel rotat ion s ens or asrequi red, refer to new module/componenti nst all at ion not e at t he top of t he DTC Index.
U3000-04Control Module GeneralFailure Informat ionSyst em Int ernal Fail ures
CAN Bus faul tLoss of power t o moduleIncorrect componentins t al ledModule i nternal fai lure
Carry out CAN net work and power feed t es ts us ingmanufact urer approved di agnos t ic s yst em. Checkcorrect s t eering wheel rot ati on s ens or is ins tall ed.Ins tall a new s teeri ng wheel rotat ion s ens or asrequi red, refer to new module/componenti nst all at ion not e at t he top of t he DTC Index.U3000-14Control Module GeneralElectrical Fai lures Ci rcuits hort t o ground or open
Loss of power t o moduleModule i nternal fai lureCarry out power feed t est s us ing manufact urerapproved diagnost ic sys tem. Ins tal l a new s teeringwheel rot ati on s ens or as required, refer t o newmodul e/component ins t al lat ion note at the t op oft he DTC Index.
U3000-1DControl Module GeneralElectrical Fai lures Ci rcuitcurrent out of range
Loss of power t o moduleModule i nternal fai lureCarry out power feed t est s us ing manufact urerapproved diagnost ic sys tem. Ins tal l a new s teeringwheel rot ati on s ens or as required, refer t o newmodul e/component ins t al lat ion note at the t op oft he DTC Index.
U3000-44Control Module Sys t emInt ernal Failures Datamemory fai lure
Module i nternal fai lureIns tall a new s teeri ng wheel rotat ion s ens or asrequi red, refer to new module/componenti nst all at ion not e at t he top of t he DTC Index.U3000-48Control Module Sys t emInt ernal FailuresSupervis ion s oft warefai lure
Module i nternal fai lureIns tall a new s teeri ng wheel rotat ion s ens or asrequi red, refer to new module/componenti nst all at ion not e at t he top of t he DTC Index.
U3000-49Control Module Sys t emInt ernal Failures Int ernalelectronic fai lure
Loss of power t o moduleModule i nternal fai lureCarry out power feed t est s us ing manufact urerapproved diagnost ic sys tem. Ins tal l a new s teeringwheel rot ati on s ens or as required, refer t o newmodul e/component ins t al lat ion note at the t op oft he DTC Index.
U3000-61Control Module Algori thmBas ed Fai lures Si gnalcalcul ati on fai lure
Steering wheel rot at ions ens or mi s-ali gnedModule i nternal fai lure
Check for correct i nst all at ion of s ens or. Ins t al l anew st eeri ng wheel rotat ion s ensor as requi red,refer t o new module/component ins tal lati on note att he t op of the DTC Index.

Publi s hed: 05-May-2011
General Information - Diagnostic Trouble Code (DTC) IndexDTC:
Transmission Control Module (TCM)
Des cript ion and Operat ion
• NOTE: If a cont rol module or component i s s uspect and the vehicl e remai ns under ma nufacturer warrant y, refer t o t he
W arranty Pol icy and Procedures manual (s ect ion B1.2), or determine i f any pri or appr oval program is i n operat ion, before
t he replacement of a component.
• NOTE: Generic scan t ool s may not read the codes li st ed, or may read only 5-digi t c odes . Match t he 5 digi ts from t he s can
t ool t o t he fi rs t 5 di gi ts of the 7-digit code li s ted t o i dent ify the fault (the las t 2 digi ts gi ve ext ra informati on read by the
manufacturer-approved di agnos ti c s ys t em).
• NOTE: W hen performing volt age or res is t ance t est s , always use a digi tal mult imeter (DMM) accurat e t o t hree deci mal
places, and wi th an up-t o-date cal ibrat ion cert ificate. W hen tes ti ng res is t ance al wa ys take t he res is t ance of t he DMM
leads i nt o account .
• NOTE: Check and recti fy bas ic faul ts before beginni ng diagnos t ic rout ines i nvol vi n g pinpoint t es t s.
• NOTE: Ins pect connect ors for s igns of water ingres s , and pins for damage and/or co rros ion.
• NOTE: If DTCs are recorded and, aft er performi ng the pi npoi nt tes ts , a fault is no t present , an int ermi tt ent concern may
be t he caus e. Always check for loose connect ions and corroded terminals .
Des cript ion And Operat ion
For a detail ed descripti on of the trans mi ss i on cont rol s ys t em, refer to t he relevant Des cript ion and O perati on sect ion i n the
works hop manual . For addit ional informat ion, refer t o: Trans mis s ion Des cript ion (307-01 Aut omati c
Trans mis s ion/Transaxle, Des cript ion and Operat ion).
Transmission control module (TCM) DT C Description Possible Cause Action
P0218-68 Trans mis s ion flui d
overtemperat ure condit ion Transmis si on fluid level l ow Transmis si on fluid
cooler/hos es are
obs t ructed/damaged/blocked. Mechanical fault i n the
trans mi ss i on Check t he transmis s ion fluid level and
condit ion. Check t he t rans mis s ion flui d cool er
/hos es for s igns of obst ruct ion/damage
/blockage. Recti fy as necess ary. Refer t o t he
warrant y poli cy and procedures manual if t he
trans mi s si on is sus pect .
P0500-00 Vehi cle s peed s ens or A
(out put s haft s peed
s ens or) Vehi cl e s peed sens or A
ci rcuit : short ci rcuit t o ground Vehi cl e s peed sens or A
ci rcuit : open ci rcuit Vehi cl e s peed sens or A faul t Check t he vehi cl e s peed sens or A and circui ts .
Refer to the el ect ri cal guides . Rect ify as
neces sary.
P056-100 Sys t em volt age unst able Bat tery faul t Chargi ng s yst em fault Check t he batt ery and charging sys tems . Refer
to the el ect ri cal guides. Recti fy as neces sary.
P0562-00 Sys t em volt age low Bat tery faul t Chargi ng s yst em fault
P0601-00
Int ernal cont rol module
memory checksum error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Reconfi gure t he module us ing the approved
di agnos t ic s yst em.
P0603-00 Int ernal cont rol module
keep al ive memory (KAM)
error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Refer to the warrant y pol icy and procedures
manual i f the TCM is s us pect .
P0604-00 Int ernal cont rol module
random acces s memory
(RAM) error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P0605-00
Int ernal cont rol module
read only memory (ROM)
error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P0614-00
Engi ne cont rol module
(ECM)/t rans mi ss i on cont rol
module (TCM) incompati bl e Incorrect s oft ware i n TCM Reconfi gure t he module us ing the approved
di agnos t ic s yst em.
P062F-00 Int ernal cont rol module
electrically eras abl e
programmabl e read onl y
memory (EEPROM) error Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Refer to the warrant y pol icy and procedures
manual i f the TCM is s us pect .
P0705-00 Trans mis s ion range sens or
A circui t (PRNDL i nput ) Incorrect adjus tment of t he
gear s elector lever cabl e Incorrect adjus tment of t he
gear posi ti on s ens or Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Check t he adjus tment of t he gear s elector l ever
cable and sens or.
For addit ional informati on, refer t o: Sel ect or Lever Cabl e Adjus t ment (307-05 Aut omati c
Transmis s ion/Trans axle External Cont rols ,
General Procedures ).
Refer to the warrant y pol icy and procedures
manual i f the TCM is s us pect .
P0706-00 Trans mis s ion range sens or
A circui t range/performance Incorrect adjus tment of t he
gear s elector lever cabl e Incorrect adjus tment of t he
gear posi ti on s ens or Int ernal t rans mi ss i on cont rol Check t he adjus tment of t he gear s elector l ever
cable.
For addit ional informati on, refer t o: Sel ect or Lever Cabl e Adjus t ment (307-05 Aut omati c
Transmis s ion/Trans axle External Cont rols ,