2006 LAND ROVER FRELANDER 2 transmission fluid

Publi s hed: 11-May-2011
Automatic Transmission/Transaxle - TransmissionTD4 2.2L Diesel
Removal
Special T ool(s) 205-754A
Spli tt er, Ball Joint s 211-316
Separat or, Ball Joi nt
General Equipment Powert rai n Jack
• NOTE: If the t rans mi ss ion is t o be removed for acces s , there is no need t o drai n t he transmis s ion fluid as long as t he
fl uid cooler is not di sconnect ed from t he t rans mis s ion as s embly.
• NOTE: If the t rans mi ss ion is t o be removed for acces s , there is no need t o drai n t he transmis s ion fluid as long as t he
fl uid cooler is not di sconnect ed from t he t rans mis s ion as s embly.
Remove t he bat t ery t ray.
Refer t o: Bat t ery Tray (414-01 Bat tery, Mount ing and Cables ,
Removal and Ins tall ati on).
1.
2. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
2.
Siphon t he fl uid from t he power s t eering res ervoi r.
3. 4. W ARNING: Make sure t hat a new s teeri ng
column flexibl e coupl ing bolt i s ins t al led.
Di sconnect t he lower s teeri ng column from t he st eeri ng
gear.
4.
Remove t he s tart er mot or.
Refer t o: Start er Motor (303-06B Starti ng Sys t em - TD4 2.2L Dies el,
Removal and Ins tall ati on).
5.

Publi s hed: 11-May-2011
Automatic Transmission/Transaxle - TransmissionI6 3.2L Petrol
Installation
General Equipment Powert rai n Jack
Inst all t he TCM.
T orque: 24 Nm 1.
Inst all t he transmis si on s elector lever.
T orque: 13 Nm 2.
Inst all t he transmis si on fluid cooler.
T orque: 10 Nm 3.
Remove t he torque convert er retai ner.
4.
5. CAUTIONS: Make s ure that t he torque convert er remains in t he
t rans mis s ion. Make s ure that t he component is correctl y located on t he
l ocati ng dowels . Make s ure that t he mat ing faces are clean and free of
corros i on and forei gn mat erial .
• NOTE: This st ep requires t he aid of another t echnician.
Inst all t he transmis si on and convert er.
5.
Inst all t he transmis si on ret aining bol ts .
T orque: 47 Nm 6.
Remove t he transmis si on s upport.
General Equi pment: Powert rai n Jack 7.
Inst all t he engi ne mount bracket .
T orque: 90 Nm 8.
Inst all t he engi ne mount LH.
T orque: 175 Nm 9.
10. W ARNING: Make sure t hat new nut s are ins tal led.
Inst all t he bracket .
T orque: M12 80 Nm M8
25 Nm 10.
Remove t he engi ne s upport .
11.

Publi s hed: 11-May-2011
Automatic Transmission/Transaxle - TransmissionTD4 2.2L Diesel
Installation
General Equipment Powert rai n Jack
• NOTE: If the t rans mi ss ion is t o be removed for acces s , there is no need t o drai n t he transmis s ion fluid as long as t he
fl uid cooler is not di sconnect ed from t he t rans mis s ion as s embly.
• NOTE: If the t rans mi ss ion is t o be removed for acces s , there is no need t o drai n t he transmis s ion fluid as long as t he
fl uid cooler is not di sconnect ed from t he t rans mis s ion as s embly.
1. CAUTION: Make s ure that the dowel s are st il l locat ed on t he
engine and not t he trans mi s si on.
Remove t he torque convert er retai ner.
1.
2. CAUTIONS: Make s ure that t he torque convert er remains in t he
t rans mis s ion. Make s ure that t he component is correctl y located on t he
l ocati ng dowels . Make s ure that t he mat ing faces are clean and free of
corros i on and forei gn mat erial . Make s ure that t he dowel s are s ti ll located on the engine and
not the trans mi s si on.
• NOTE: This st ep requires t he aid of another t echnician.
Inst all t he transmis si on and convert er.
T orque: 47 Nm 2.

Publi s hed: 11-May-2011
Transmission/Transaxle Cooling - Transmission Cooling
Des cript ion and Operat ion
COMPONENT LOCATION - STANDARD CLIMATE
ItemPart NumberDescription
1-Transmis s ion fluid cooler
COMPONENT LOCATION - HOT CLIMATE

Publi s hed: 11-May-2011
Transmission/Transaxle Cooling - Transmission Cooling
Diagnosi s and Tes ti ng
Principles of Operation
For a detail ed descripti on of the aut omati c transmis s ion cool ing s ys tem, refer t o t he relevant Descripti on and Operat ions ect ion i n t he works hop manual .REFER to: Trans mi ss i on Cool ing (307-02 Trans mi ss ion/Transaxle Cool ing, Descripti on and Operat ion).
Inspection and Verification
1. Verify t he cus t omer concern.1.
2. Vis ually ins pect for s ys tem int egrit y and obvi ous s igns of mechanical damage.2.
Visual Inspection
Mechanical
Feed and ret urn t ubesConnect ions t o the aut omati c t ransmis s ion and t he automat ic t rans mis s ion flui d cool erAutomat ic trans mi ss i on fl uid l evel
3. If an obvious cause for an obs erved or report ed concern is found, correct t he caus e (if pos s ible) beforeproceeding t o t he next s t ep3.
4. If t he caus e is not vis ually evi dent , verify t he sympt om and refer t o t he Sympt om Chart.4.
Symptom Chart
ConditionPossible CauseAction
Over heat ing of t heautomat ict rans mis s ion
Obs truct ion i n t he automat ict rans mis s ion fluid cool erFl us h out t he automat ic t rans mi ss ion fl ui d cool er wit hnew aut omati c t rans mis s ion fluidIf t he fl ushi ng is uns ucces sful, ins t al l a new cooler.REFER t o: Transmis s ion Flui d Cooler - I6 3.2L Petrol(307-02 Trans mi ss i on/Trans axl e Cooling, Removal andIns tall ati on) /Trans mi s si on Fluid Cool er - TD4 2.2L Di es el (307-02Trans mi s si on/Trans axl e Cooli ng, Removal andIns tall ati on).
Over heat ing of t heautomat ict rans mis s ion
Obs truct ion i n t he automat ict rans mis s ion fluid tubesFl us h out t he automat ic t rans mi ss ion fl ui d cool er tubeswit h new automat ic t rans mi ss i on fl ui dIf t he fl ushi ng is uns ucces sful ins tall new aut omati ct rans mi ss i on fl ui d cooler tubes
Loss of aut omati ct rans mis s ion flui dConnect ions to the aut omati ct rans mis s ion and t he automat ict rans mis s ion fluid cool er
Check t he int egrit y of tubes , connect ions and s ealsCheck t he torque of t he t ube fi xi ngs.REFER t o: Specificati ons (307-02Trans mi s si on/Trans axl e Cooli ng, Speci fi cat ions ).
Loss of aut omati ct rans mis s ion flui dLeak at aut omati c t ransmis s ion fluidcool erCheck t he int egrit y of tubes , connect ions and s ealsCheck t he torque of t he t ube fi xi ngs.REFER t o: Specificati ons (307-02Trans mi s si on/Trans axl e Cooli ng, Speci fi cat ions ).Check for aut omat ic trans mi s si on fl uid contami nat ionof t he engine cool ant. Inst all new cooler as required.REFER t o: Transmis s ion Flui d Cooler - I6 3.2L Petrol(307-02 Trans mi ss i on/Trans axl e Cooling, Removal andIns tall ati on) /Trans mi s si on Fluid Cool er - TD4 2.2L Di es el (307-02Trans mi s si on/Trans axl e Cooli ng, Removal andIns tall ati on).

Publi s hed: 11-May-2011
Transmission/Transaxle Cooling - Transmission Fluid CoolerI6 3.2L Petrol
Removal and Inst all ati on
Removal
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -General Informat ion, Specificati ons).
1.
2. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
2.
Drai n t he t ransmis s ion fluid.
Refer t o: Transmis s ion Flui d Drai n and Refi ll - I6 3.2L Pet rol (307-01Automat ic Transmis si on/Trans axl e, General Procedures ).
3.
Clamp the relevant hos es , to mini mis e t he cool ant los s.4.
5. CAUTION: Be prepared to col lect escapingcool ant.
Di sconnect t he 2 t rans mis s ion flui d cool er coolanthos es .
5.

Publi s hed: 11-May-2011
Transmission/Transaxle Cooling - Transmission Fluid CoolerTD4 2.2L Diesel
Removal and Inst all ati on
Removal
Remove t he cover and dis connect the bat tery ground cabl e.
Refer t o: Specificati ons (414-00 Bat tery and Charging Sys tem -
General Informat ion, Specificati ons).
1.
2. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
2.
Drai n t he t ransmis s ion fluid.
Refer t o: Transmis s ion Flui d Drai n and Refi ll - TD4 2.2L Dies el (307-01 Automat ic Trans mi s si on/Trans axl e, General Procedures ).
3.
Clamp the relevant hos es , to mini mis e t he cool ant los s.
4. 5. CAUTION: Be prepared to col lect escaping
cool ant.
Di sconnect t he 2 t rans mis s ion flui d cool er coolant
hos es .
5.

Publi s hed: 11-May-2011
Manual Transmission/Transaxle and Clutch - General Information - Clutch
System Bleeding
General Procedures
Check that all t he clutch l ine connect ions are ti ght and t hat thereare no s igns of leaks.1.
2.
3. W ARNING: Do not allow dirt or forei gn li qui ds to ent er theres ervoi r. Us e only new brake fl uid of t he correct s peci fi cat ion fromairti ght cont ai ners . Do not mix brands of brake fl uid as t hey may notbe compati ble.
CAUTION: Brake fl ui d wi ll damage paint fi nis hed s urfaces. Ifs pil led, immedi at ely remove t he fl uid and clean t he area wit h wat er.
Remove t he brake fluid res ervoir cap.
3.
Fil l the brake fl ui d res ervoi r to t he MAX mark.4.