2006 ACURA CSX ECO mode




(#'


 )
21-88 Climate Control
A/C Condenser Replacement
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft)
A
6x1.0mm
9.8 N·m (1.0 kgf·m, 7.2 lbf·ft) A 6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
A
A
B CD
1. Recover the refrigerant with a recovery/recycling/
charging station (see page 21-90).
2. Remove the front grille:  ’06-08 models (see page 20-160)
 ’09 model (see page 20-161)
3. Remove the bolts, then disconnect the discharge hose (A) from the A/C condenser.
4. Remove the bolt, then disconnect the receiver line (A) from the A/C condenser. 5. Remove the bolts and the A/C condenser upper
mount brackets (A).
6. Lift the tab (A) to release the lock, then remove the outside air temperature sensor (B) from the bracket.
Disconnect the 2P connector (C), then remove the
clip (D).
7. Remove the hood latch (see page 20-181).
08/08/21 14:43:49 61SNR030_210_0089
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
Performance Test
21-99
A/C System Test
A
B
 Air conditioning refrigerant or lubricant vapor can irritate your eyes, nose, or throat.
 Be careful when connecting service equipment.
 Do not breathe refrigerant or vapor.
The performance test will help determine if the A/C
system is operating within specifications.
NOTE:  If accidental system discharge occurs, ventilate the work area before resuming service.
 Additional health and safety information may be obtained from the refrigerant and lubricant
manufacturers.
1. Do the A/C system inspection (see page 21-6), and correct any problems found.
2. Connect an R-134a refrigerant recovery/recycling/ charging station to the high-pressure service port
and the low-pressure service port, following the
equipment manufacturer’s instructions.
3. Determine the relative humidity and air temperature.
4. Open the glove box. Remove the glove box stop on each side, then let the glove box hang down
(see page 20-104).
5. Insert a thermometer (A) in the center vent. 6. Place a thermometer (B) near the blower unit’s
recirculation inlet duct.
7. Test conditions:  Move the vehicle out of direct sunlight and let itcool down to the surrounding (ambient)
temperature. If necessary, wash the vehicle to
cool it down more quickly.
 The ambient temperature must be at least 16 °C (60 °F).
 Open the hood.
 Open the front doors.
 Set the temperature control dial to Max Cool, the mode control switch to Vent, and the
recirculation control switch to Recirculate.
 Turn the A/C switch ON and the fan switch to Max.
 Hold the engine speed at 1,500 rpm.
 No driver or passengers in the vehicle.
8. Inspect the A/C components for the following conditions:
 A/C compressor clutch not engaged.
 Abnormal frost areas.
 Unusual noises.
If you observe any of these conditions, refer to the
Symptom Troubleshooting Index.
9. After running the air conditioning for 10 minutes under the above test conditions, read the delivery
temperature from the thermometer in the center
vent, the intake temperature near the blower unit,
and the discharge (high) and suction (low)
pressures on the A/C gauges.
(cont’d)
08/08/21 14:44:55 61SNR030_210_0100
ProCarManuals.com
DYNOMITE -2009-

(#'
/)
Body Electrical
Body Electrical..................................
..................................
Relay and Control Unit
Locations . 22-7
................
Connectors and Harnesses . 22-13
........................
........................
Fuse/Relay Boxes . 22-58
......................
......................
Power Distribution . 22-60
....................
....................
Ground Distribution . 22-64
Under-hood Fuse/Relay Box
Under-dash Fuse/Relay Box
Battery
Relays
Ignition Switch
Multiplex Integrated Control System Keyless/Power Door Locks/Security
System
Horns
Exterior Lights
Turn Signal/Hazard Warning Lights
Interior Lights.............................................. .....
..............................................
.....
Special Tools . 22-2
General Troubleshooting Information . 22-3
.......................... ..........................
Removal and Installation . 22-65
..........................
..........................
Removal and Installation . 22-66
.......................................................................................... .............
................................................
.......................................... .............
Battery Test
. 22-67
Battery Terminal Disconnection and Reconnection . 22-68
Battery Removal and Installation . 22-69
.......................................
.......................................
Power Relay Test . 22-70
............................................................. ..............................................
.............................................................
..............................................
Test
. 22-72
Replacement . 22-72
...................... .....
......................
...................................
.........................
..........................
.......................... .........................
............
................
.......................................... ................................
......................................... ......................
.....
......................
...................................
.........................
..........................
.......................... .........................
............
................
.......................................... ................................
.........................................
Component Location Index
. 22-73
General Troubleshooting Information . 22-74
DTC Troubleshooting Index . 22-77
System Description . 22-80
Troubleshooting-B-CAN System Diagnosis Test Mode A . 22-93
Troubleshooting-B-CAN System Diagnosis Test Mode B . 22-94
Troubleshooting-B-CAN System Diagnosis Test Mode C . 22-95
Troubleshooting-B-CAN System Diagnosis Test Mode D . 22-96
Troubleshooting-B-CAN System Diagnosis Test Mode 1 and
Test Mode 2 (Without the HDS) . 22-97
Sleep and Wake-up Mode Test . 22-99
Circuit Diagram . 22-100
DTC Troubleshooting . 22-102
MICU Input Test . 22-109 ......................
...................................
.......................................... ......................................................
.............................
......................................... ................................................
............................... ...............................
....................................... .................
......................
...................................
.......................................... ......................................................
.............................
......................................... ................................................
............................... ...............................
....................................... .................
Component Location Index
. 22-112
System Description . 22-114
Circuit Diagram . 22-116
DTC Troubleshooting . 22-120
Symptom Troubleshooting . 22-126
Tripped Sensor History . 22-130
MICU Input Test . 22-131
Door Lock Actuator Test . 22-137
Door Lock Knob Switch Test . 22-138
Door Lock Switch Test . 22-139
Door Key Cylinder Switch Test . 22-140
Trunk Lid Release Actuator Test . 22-141
Hood Switch Test . 22-141
Transmitter Test/Replacement . 22-142
......................
.......................................... ............................
....................................... ......................
.......................................... ............................
.......................................
Component Location Index
. 22-145
Circuit Diagram . 22-146
Horn Test/Replacement . 22-146
Horn Switch Test . 22-147
......................
.......................................... ................................
.........................................
........................................... ..............................
............................... ........
............................... .............................
.............................
................................
..................................... ............................... ........................................
.............
......................
.......................................... ................................
.........................................
........................................... ..............................
............................... ........
............................... .............................
.............................
................................
..................................... ............................... ........................................
.............
Component Location Index
. 22-148
Circuit Diagram . 22-150
DTC Troubleshooting . 22-157
MICU Input Test . 22-163
Combination Light Switch Test/ Replacement . 22-166
HID Bulb Replacement . 22-168
HID Unit Replacement . 22-169
HID Lamp System Troubleshooting . 22-170
Headlight Adjustment . 22-173
Headlight Replacement . 22-174
Fog Light Replacement . 22-175
Fog Light Adjustment . 22-176
Bulb Replacement . 22-177
Taillight Replacement . 22-179
Inner Taillight Replacement . 22-179
License Plate Light Replacement . 22-180
High Mount Brake Light Replacement . 22-180
Brake Pedal Position Switch Test . 22-181
......................
.......................................... ................................
.........................................
.................................. .......
......................
.......................................... ................................
.........................................
.................................. .......
Component Location Index
. 22-182
Circuit Diagram . 22-184
DTC Troubleshooting . 22-186
MICU Input Test . 22-188
Hazard Warning Switch Test/Replacement . 22-192
Side Turn Signal Light Replacement . 22-192
......................
..........................................
........................................... ...............
.......................... ............
.................... ................
...................... .............
......................
..........................................
........................................... ...............
.......................... ............
.................... ................
...................... .............
Component Location Index
. 22-193
Circuit Diagram . 22-194
Front Individual Map Light Test/ Replacement . 22-196
Ceiling Light Test/Replacement . 22-197
Trunk Light Replacement . 22-197
Ambient Light Test/Replacement . 22-198
Courtesy Light Replacement . 22-198
Glove Box Light Test/Replacement . 22-199
Vanity Mirror Light Test/Replacement . 22-199
Interior Light Switch Test/Replacement . 22-200
Trunk Lid Latch Switch Test . 22-200
Footwell Light Test/Replacement . 22-201
08/08/21 14:22:03 61SNR030_220_0002
ProCarManuals.com
DYNOMITE -2009-




Wire Color Codes
How to Check for DTCs with the Honda
Diagnostic System (HDS)
22-6 Body Electrical
General Troubleshooting Information (cont’d)
WHT/BLK
A
The following abbreviations are used to identify wire
colors in the circuit schematics:
...................................
.....................................
..................................... ....................................
....................................
....................................
....................................
....................................
....................................
....................................
.................................... .............................................................
...................................
.....................................
..................................... ....................................
....................................
....................................
....................................
....................................
....................................
....................................
.................................... .............................................................
WHT . White
YEL . Yellow
BLK . Black
BLU . Blue
GRN . Green
RED . Red
ORN . Orange
PNK . Pink
BRN . Brown
GRY . Gray
PUR . Purple
LT BLU . Light Blue
LT GRN . Light Green
The wire insulation has one color or one color with
another color stripe. The second color is the stripe. NOTE: For specific operations, refer to the user’s
manual that came with the Honda Diagnostic System
(HDS).
1. Connect the HDS to the data link connector (A) located under the driver’s side of the dashboard.
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle, if it doesn’t, do the DLC circuit troubleshooting
(see page 11-204).
4. Enter the BODY ELECTRICAL, then select the TEST MODE menu.
5. Check for DTCs with the HDS.
6. If any DTCs are indicated, note them, and go to the indicated DTC troubleshooting.
08/08/21 14:22:05 61SNR030_220_0008
ProCarManuals.com
DYNOMITE -2009-

Î(#')
22-8Relay and Control Unit Locations
Dashboard
GAUGE CONTROL
MODULE (TACH)
GAUGE CONTROL MODULE
(SPEEDO)
POWER WINDOW RELAY PGM-FI MAIN RELAY 2
(FUEL PUMP)
STARTER CUT RELAY
MICU
UNDER-DASH FUSE/
RELAY BOX
View of front side View of rear sideFRONT ACCESSORY POWER SOCKET RELAY
CONSOLE ACCESSORY POWER SOCKET RELAY
FOG LIGHT RELAY
(TYPE S and ’08 PREMIUMand ’09 models)
Wire colors: BLU, WHT, BLK, and PUR
Wirecolors:YEL,GRN,BLK,andPUR
Wire colors: PNK,
WHT, ORN, and WHT
08/08/21 14:22:06 61SNR030_220_0010
ProCarManuals.com
DYNOMITE -2009-

•••
•••´
´
•••
Under-dash Fuse/Relay Box
Fuse
Number Amps
Component(s) or Circuit(s) Protected
22-62Power Distribution
Fuse to Components Index (cont’d)
1 7.5 A Power mirror switch light
2 15 A ECM/PCM, Fuel pump (via PGM-FI main relay 2), Immobilizer-keyless control unit
3 10 A Alternator, CMP sensor A, ECM/PCM (via brake pedal position switch), ELD, EVAP canister purge valve, MAF
sensor/IAT sensor, Reverse lockout solenoid , Secondary HO2S (sensor 2)
4 7.5 A ABS modulator-control unit , EPS control unit, VSA modulator-control unit , Yaw rate-lateral acceleration sensor
5 15 A Seat heaters (via seat heater relays)
6 20 A Fog light relay, Fog lights (via fog light relay)
7 Not used
8 Not used
9 7.5 A ODS unit, Passenger’s airbag cutoff indicator, SRS unit
10 7.5 A Back-up light (M/T), Gauge control module (speedo), Gauge control module (tach), MICU, Shift lock solenoid (A/T), TPMS control unit
11 10 A SRS unit
12 10 A Right headlight (high beam)
13 10 A Left headlight (high beam)
14 7.5 A Audio unit light , Climate control unit light, Dash lights brightness controller and odometer select/reset switch light, Driver’s footwell light , Driver’s seat heater switch light, Glove box light, Hazard warning switch light,
Moonroof switch light, Navigation unit , Park pin switch light (A/T), Passenger’s airbag cutoff indicator light,
Passenger’s footwell light , Passenger’s seat heater switch light, Steering wheel switches light (via cable reel),
VSA OFF switch light
15 7.5 A Parking lights, Taillights, License plate lights, Side marker lights
16 10 A Right headlight (low beam) 15 A Right HID unit
17 10 A Left headlight (low beam) 15 A Left HID unit
18 20 A MICU ( B H/L HI)
19 15 A MICU ( B SMALL LT)
20 Not used
1: ’06-07 Touring and Premium models
2: ’07 TYPE S and ’08-09 models
3: ’08-09 models
4: TYPE S model
5: With HID
6: Without HID
7: TYPE S and ’08 Premium and ’09 models
8: Without navigation system
9: With navigation system
4
1 2
2
7
3
8 49
4
6
5
6
5
08/08/21 14:24:03 61SNR030_220_0064
ProCarManuals.com
DYNOMITE -2009-

µ
(#'
)
GroundComponent or Circuit Grounded
22-64Ground Distribution
Ground to Components Index
G1 Battery
G2 Engine
G3 Transmission housing
G101 A/T clutch pressure control solenoid valves A, B, C (A/T), CKP sensor, CMP sensor A, CMP sensor B, Data link connector (DLC), ECM/PCM (LG1), ECM/PCM (LG2), ECM/PCM (PG1), ECM/PCM (PG2), ECM/PCM (PGMETCS), EGR valve (K20Z2 engine), Ignition
coils, Immobilizer-keyless control unit, Rocker arm oil control solenoid, Rocker arm oil pressure switch, Transmission range
switch (A/T), VTC oil control solenoid valve
Shielding between the ECM/PCM and Knock sensor (KS) has wire.
Shielding between the ECM/PCM and Secondary HO2S (Sensor 2) has wire.
G201 Right fog light , Right front parking light, Right front side marker light, Right front turn signal light, Right headlight (high/low beams), Right HID unit , Windshield washer motor, Windshield wiper motor
G202 ABS modulator-control unit , VSA modulator-control unit
G301 A/C condenser fan motor, Blower motor relay, ELD, Left fog light , Left front parking light, Left front side marker light, Left front turn signal light, Left headlight (high/low beams), Left HID unit , Radiator fan motor (via fan control relay)
G401 Brake fluid level switch, Clutch interlock switch (M/T), Clutch pedal position switch (M/T), Hood switch, MICU (PG), Power transistor, Washer fluid level switch (G401 connects to G601 via under-dash fuse/relay box)
G402 EPS control unit
G403 Torque sensor
G501 Dash lights brightness controller and odometer select/reset switch, Driver’s door key cylinder switch, Driver’s door lock knob switch, HandsFreeLink control unit , MICU (SG), VSA OFF switch
G502 Data link connector (DLC), Front accessory power socket, Glove box light, Right power mirror defogger, Right side turn signal light
G503 Accessory power socket relays (front and console), Driver’s door lock switch, Gauge control module (tach), Left power mirror defogger, Left side turn signal light, Moonroof control unit/motor, Power mirror switch light, Power mirror switch, Power
window master switch (main switch), Power window master switch, Vanity mirror lights (driver’s and front passenger’s)
G504 Cable reel (steering wheel switches ground), Climate control unit, Front passenger’s door lock knob switch, Front passenger’s door lock switch, Gauge control module (speedo), Gauge control module (tach), Ignition key switch, Navigation unit , TPMS
control unit
G505 Audio unit , Navigation unit
G506 Memory erase signal (MES) connector, SRS unit (2 wires)
G601 A/T gear position console panel light/Park-pin switch (A/T), Console accessory power socket , Fuel pump, MICU (PG), Seat heater relays (driver’s and front passenger’s), Seat heater switches (driver’s and front passenger’s), Seat heaters (driver’s and
front passenger’s), Stereo amplifier (G601 connects to G401 via under-dash fuse/relay box)
Shielding between the left side impact sensor (FIRST) and rear safing sensor has wire.
Shielding between the SRS unit and left side impact sensor (FIRST) has wire.
G602 Driver’s seat belt buckle switch, Front passenger’s seat belt buckle switch, Left rear door lock knob switch, MICU (SG), MICU service check connector, ODS unit, Right rear door lock knob switch, Yaw rate-lateral acceleration sensor
Shielding between the right side impact sensor (FIRST) and right side impact sensor (SECOND) have wires.
Shielding between the SRS unit and right side impact sensor (FIRST) has wire.
G603 Noise condenser Shielding between the rear safing sensor and left side impact sensor (SECOND) has wire.
G701 High mount brake light, Left back-up light, Left inner taillight, Left rear side marker light, Left rear turn signal light, Left taillight/ brake light, License plate lights, Right back-up light, Right inner taillight, Right rear side marker light, Right rear turn signal light,
Right taillight/brake light, Trunk lid release actuator/Trunk lid latch switch
G801 Rear window defogger ( )
1: ’06-07 Touring and Premium models
2: ’07 TYPE S and ’08-09 models
3: ’08-09 models
4: TYPE S and ’08 premium and ’09 models
5: With HID
6: Without navigation system
7: With navigation system
8: ’09 model with navigation system
9: ’06-08 models, and ’09 model without navigation system
10: TYPE S model
4
512 4
5
82 3
7
3
67
9
10
2
08/08/21 14:24:03 61SNR030_220_0066
ProCarManuals.com
DYNOMITE -2009-

Î
How to display DTCs on the gauge control module (tach)
How to clear the DTC
22-75
No DTCs detectedAll DTCs have been displayed
DTC detected
(the letter and four digit number on the left
represents the DTC, the right two digit is the
unit code.)
While in Test Mode 1, the DTCs which have been detected and stored individually by various B-CAN (Body-controller
Area Network) units, will be shown one by one on the odometer display when the communication between the MICU
and the gauge control module is normal. To scroll through the DTCs, press the select/reset button.
The unit that has stored the code can be identified by the number shown on the multi-information display.
MICU 10
Gauge control module 50
Climate control unit 51
HandsFreeLink control unit 94
Immobilizer-keyless control unit 96
While in Test Mode 1, press and hold down the SELECT/RESET button for more than 10 seconds.
(cont’d)
08/08/21 14:24:07 61SNR030_220_0077
ProCarManuals.com
DYNOMITE -2009-