2003 NISSAN TEANA Unified meter and

CVT SHIFT LOCK SYSTEM
CVT-183
D
E
F
G
H
I
J
K
L
MA
B
CVT

Shift Lock Control Unit Reference ValuesBCS001MT
SHIFT LOCK HARNESS CONNECTOR TERMINALS LAYOUT
SHIFT LOCK CONTROL UNIT INSPECTION TABLE
Shift lock control unit terminal data are reference values, measured between each terminal and ground.
NOTE:
Take care that the pointer of circuit tester swings only momentarily because the output time is so short. If the inspection is done with an
oscilloscope, it should be observed that the power source voltage lasts for 3.5 to 10 ms.
SCIA2004E
Terminal
(Wire color)Item Condition Judgement standard
1
(Y/R)Power source Always Battery voltage
2
(L)Detention switch (for
key)When selector lever is not in “P” position with key
inserted or ignition knob switch pushed.Battery voltage
When selector lever is in “P” position with key
inserted.Approx. 0 V
3
(R)Detention switch (for
shift)When selector lever is not in “P” position. Battery voltage
When selector lever is in “P” position. Approx. 0 V
4
(R/G)Stop lamp switchWhen brake pedal is depressed Battery voltage
When brake pedal is released Approx. 0 V
5
(V/W)Vehicle speed signal
(8pulse signal)Speed meter is operatedRefer to DI-13, "
Terminals and Refer-
ence Value for Unified Meter and A/C
Amp." .
6
(G)Ignition signalIgnition switch: except ON Approx. 0 V
Ignition switch: ON Battery voltage
7
(R/W)Shift lock solenoid

When selector lever is in “P” position, brake
pedal is depressed, and ignition switch is ON.

When selector lever is not in “P” position, igni-
tion switch is ON, and vehicle speed is 10 km/h
(6 MPH) or less.

Within 3 minutes, after ignition switch turning to
other position from ON position, while selector
lever is not in “P” position and vehicle speed is
10 km/h (6 MPH) or less.Approx. 0 V
Except the above Battery voltage
8
(B)Ground — Approx. 0 V
9
(G/B)Key lock solenoidWhen selector lever is not “P” position.Battery voltage for approx. 0.1 sec.
(Note)
When selector lever is in “P” position. Approx. 0 V
10
(G/W)Key unlock solenoidWhen selector lever is in “P” position with ignition
switch in except ON position.Battery voltage for approx. 0.1 sec.
(Note)
Except the above. Approx. 0 V

DI-1
DRIVER INFORMATION SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION DI
A
B
DI

DRIVER INFORMATION SYSTEM
PRECAUTION ............................................................ 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
COMBINATION METERS ........................................... 4
System Description .................................................. 4
UNIFIED METER CONTROL UNIT ...................... 4
UNIFIED METER AND A/C AMP. ......................... 4
FAIL-SAFE ............................................................ 5
HOW TO CHANGE THE DISPLAY FOR ODO/
TRIP METER ........................................................ 6
POWER SUPPLY AND GROUND CIRCUIT ........ 6
SPEEDOMETER ................................................... 7
TACHOMETER ..................................................... 7
LOW WATER TEMPERATURE INDICATOR
LAMP, HIGH WATER TEMPERATURE WARN-
ING LAMP ............................................................. 7
FUEL GAUGE ....................................................... 7
Component Parts and Harness Connector Location ..... 7
Arrangement of Combination Meter ......................... 8
Internal Circuit .......................................................... 9
Wiring Diagram — METER — ................................ 10
Terminals and Reference Value for Combination
Meter ...................................................................... 12
Terminals and Reference Value for Unified Meter
and A/C Amp. ......................................................... 13
Self-Diagnosis Mode of Combination Meter ........... 13
SELF-DIAGNOSIS MODE FUNCTION ............... 13
OPERATION PROCEDURE ............................... 13
CONSULT-II Function ............................................ 14
Trouble Diagnosis .................................................. 14
HOW TO PROCEED WITH TROUBLE DIAGNO-
SIS ...................................................................... 14
PRELIMINARY CHECK ...................................... 15
SYMPTOM CHART 1 .......................................... 17
SYMPTOM CHART 2 .......................................... 17
Power Supply and Ground Circuit Inspection ........ 18
Vehicle Speed Signal Inspection ............................ 20
Engine Speed Signal Inspection ............................ 21
Engine Coolant Temperature Signal Inspection ..... 21Fuel Level Sensor Signal Inspection ...................... 22
Fuel Gauge Does Not Move to FULL position ........ 23
Electrical Components Inspection .......................... 24
CHECK FUEL LEVEL SENSOR UNIT ................ 24
Removal and Installation of Combination Meter ..... 25
REMOVAL ........................................................... 25
INSTALLATION ................................................... 25
Disassembly and Assembly of Combination Meter ... 25
DISASSEMBLY ................................................... 26
ASSEMBLY ......................................................... 26
UNIFIED METER AND A/C AMP .............................. 27
System Description ................................................. 27
INPUT/OUTPUT SIGNALS ................................. 27
Schematic ............................................................... 28
CONSULT-II Function (METER A/C AMP) ............. 29
CONSULT-II BASIC OPERATION ....................... 29
SELF-DIAGNOSTIC RESULTS ........................... 29
DATA MONITOR ................................................. 30
DTC [U1000] CAN Communication Circuit ............. 32
DTC [B2202] Meter Communication Circuit ........... 32
DTC [B2205] Vehicle Speed Circuit ........................ 34
Removal and Installation of Unified Meter and A/C
Amp. ....................................................................... 34
REMOVAL ........................................................... 34
INSTALLATION ................................................... 34
WARNING LAMPS .................................................... 35
System Description ................................................. 35
OIL PRESSURE WARNING LAMP ..................... 35
Schematic ............................................................... 36
Wiring Diagram — WARN — .................................. 37
Oil Pressure Warning Lamp Stays Off (Ignition
Switch ON) ............................................................. 45
Oil Pressure Warning Lamp Does Not Turn Off (Oil
Pressure Is Normal) ................................................ 46
Electrical Component Inspection ............................ 47
OIL PRESSURE SWITCH ................................... 47
A/T INDICATOR ........................................................ 48
Wiring Diagram — AT/IND — ................................. 48
A/T Indicator Is Malfunction .................................... 50
CVT INDICATOR ....................................................... 52

DI-2 Wiring Diagram — CVTIND — ............................... 52
CVT Indicator Is Malfunction .................................. 54
WARNING CHIME ..................................................... 56
System Description ................................................. 56
POWER SUPPLY AND GROUND CIRCUIT ....... 56
IGNITION KEY WARNING CHIME (WITHOUT
INTELLIGENT KEY) ............................................ 56
IGNITION KEY WARNING CHIME (WITH INTEL-
LIGENT KEY) ...................................................... 57
LIGHT WARNING CHIME ................................... 57
Component Parts and Harness Connector Location ... 58
Schematic ............................................................... 59
Wiring Diagram — CHIME — ................................. 60
Terminals and Reference Value for BCM ................ 63
Terminals and Reference Value for Unified Meter
and A/C Amp. ......................................................... 64
Terminals and Reference Value for Combination
Meter ...................................................................... 65
CONSULT-II Function ............................................. 65
DIAGNOSTIC ITEMS DESCRIPTION ................. 65
CONSULT-II BASIC OPERATION PROCEDURE ... 65
DATA MONITOR .................................................. 65
ACTIVE TEST ...................................................... 66
Trouble Diagnosis ................................................... 66
HOW TO PROCEED WITH TROUBLE DIAGNO-
SIS ....................................................................... 66
PRELIMINARY CHECK ....................................... 66
Key Warning Chime and Light Warning Chime Does
Not Operated .......................................................... 67
Key Warning Chime Does Not Operate (Without
Intelligent Key) ........................................................ 69
Key Warning Chime Does Not Operate (With Intel-
ligent Key, When Mechanical Key Is Used) ............ 71
Key Warning Chime Does Not Operate (With Intel-
ligent Key, When Intelligent Key Is Carried With The
Driver) ..................................................................... 73
Light Warning Chime Does Not Operate ................. 75
CAN COMMUNICATION ........................................... 76
System Description ................................................. 76
CAN Communication Unit ....................................... 76

DI-4
COMBINATION METERS

COMBINATION METERSPFP:24814
System DescriptionBKS001RX
UNIFIED METER CONTROL UNIT

Speedometer, odo/trip meter, tachometer and fuel gauge are controlled by the unified meter control unit,
which is built into the combination meter. Unified meter control unit receives signals from unified meter
and A/C amp.

Warning lamp and indicator lamp of combination meter are controlled by signals drawn from the unified
meter and A/C amp.

Digital meter is adopted for odo/trip meter*.
*The record of the odo meter is kept even if the battery cable is disconnected. The record of the trip meter
is erased when the battery cable is disconnected.

Odo/trip meter and shift indicator segments can be checked in diagnosis mode.

Meters/gauges can be checked in diagnosis mode.
Illumination control

Unified meter control unit produces an illumination output of the
combination meter when the ignition switch is “ON”.

Light levels can be adjusted by pressing illumination control
switch of the combination meter when lighting switch is “ON”.

Illumination control switch has five light level settings.
NOTE:
When it is light outside, light level cannot be adjusted by turning
on the lighting switch.
UNIFIED METER AND A/C AMP.
Refer to DI-27, "System Description" in “UNIFIED METER AND A/C AMP”.
SKIB0769E

COMBINATION METERS
DI-5
C
D
E
F
G
H
I
J
L
MA
B
DI

FA I L - S A F E
Solution When Communication Error Between the Unified Meter and A/C Amp. and the Com-
bination Meter
Function Specifications
SpeedometerReturn to zero when discontinuing communication or receiv-
ing irregular data.
Tachometer
Reset to zero by suspending communication.
Fuel gauge
Illumination control Combination meter illumination When suspending communication, change to nighttime mode.
Odo/trip meter Integrate in response to 8-pulse input.
Shift indicator The display turns off by suspending communication.
Warning buzzer The warning buzzer turns off by suspending communication.
Warning lamp/indicator lampLow water temperature indicator lamp
The lamp turns on by suspending communication. VDC OFF indicator (With VDC)
SLIP indicator (With VDC)
Brake warning lamp
ABS warning lamp
ASCD CRUISE indicator lamp
The lamp turns off by suspending communication. ASCD SET indicator lamp
Turn signal indicator lamp
High-beam indicator lamp
Front fog indicator lamp
Rear fog indicator lamp
Oil pressure warning lamp
Door warning lamp
High water temperature warning lamp
Malfunction indicator lamp
A/T CHECK warning lamp
CVT indicator lamp
KEY warning lamp
LOCK warning lamp

DI-6
COMBINATION METERS

HOW TO CHANGE THE DISPLAY FOR ODO/TRIP METER

The vehicle speed signal and the memory signals from the meter memory circuit are processed by the
combination meter and the mileage is displayed.

Depressing the odo/trip meter switch toggles the mode in the following order.

The odo/trip meter display mode toggling and trip display resetting can be identified by the amount of time
that elapses from pressing the odo/trip meter switch to releasing it.

When resetting with trip A displayed, only trip A display is reset (The same way for “trip B”).
POWER SUPPLY AND GROUND CIRCUIT
Power is supplied at all times

through 10A fuse [No. 19, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 21,

through 15A fuse [No. 17, located in the fuse block (J/B)]

to combination meter terminal 7.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 35.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 14, located in the fuse block (J/B)]

to combination meter terminal 8,

through 10A fuse [No. 12, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 22.
With the ignition switch in the ON position, power is supplied

through 15A fuse [No. 10, located in the fuse block (J/B)], and

through 15A fuse [No. 11, located in the fuse block (J/B)]

to unified meter and A/C amp. terminal 46.
Ground is supplied

to combination meter terminals 10, 11 and 12

through body grounds M71 and M72,

to unified meter and A/C amp. terminals 29 and 30

through body grounds M71 and M72.
SEL175W

COMBINATION METERS
DI-7
C
D
E
F
G
H
I
J
L
MA
B
DI

SPEEDOMETER
ABS actuator and electric unit (control unit) provides a vehicle speed signal to the unified meter and A/C amp.
with CAN communication line. After unified meter and A/C amp. received the vehicle speed signal, it changes
the signal to 8 pulse signal and provides the 8 pulse signal to the combination meter for the speedometer.
TACHOMETER
The tachometer indicates engine speed in revolutions per minute (rpm).
ECM provides an engine speed signal to unified meter and A/C amp. with CAN communication line. Unified
meter and A/C amp. provides an engine speed signal to combination meter for tachometer with communica-
tion line between unified meter and A/C amp. and combination meter.
LOW WATER TEMPERATURE INDICATOR LAMP, HIGH WATER TEMPERATURE WARNING
LAMP
ECM converts water temperature signal from water temperature sensor into data and transmits the data to uni-
fied meter and A/C amp. with CAN communication line. Unified meter and A/C amp. transmit the received
water temperature signal to the combination meter with communication line between unified meter and A/C
amp. and combination meter. Combination meter turns on/off low water temperature indicator lamp or high
water temperature warning lamp through the received water temperature signal.
FUEL GAUGE
The fuel gauge indicates the approximate fuel level in the fuel tank.
The fuel gauge is regulated by a variable ground signal supplied

from unified meter and A/C amp. terminal 36

through the fuel level sensor unit and fuel pump terminals 5 and 2

to unified meter and A/C amp. terminal 28 for the fuel gauge.
Unified meter and A/C amp. provides a fuel level signal to combination meter for fuel gauge with communica-
tion line between unified meter and A/C amp. and combination meter.
Component Parts and Harness Connector LocationBKS001RY
SKIB0770E

DI-12
COMBINATION METERS

Terminals and Reference Value for Combination MeterBKS001S2
TerminalWire
colorItemCondition
Reference value
Ignition
switchOperation or condition
7 Y/R Battery power supply OFF — Battery voltage
8 P Ignition switch ON or START ON — Battery voltage
10
B Ground ON — Approx. 0V 11
12
17 V Ignition switch ACC or ON ACC — Battery voltage
18 G/BTX communication line (To
unified meter and A/C amp.)ON —
19 RRX communication line (From
unified meter and A/C amp.)ON —
20 V/WVehicle speed signal
(8-pulse)ONSpeedometer operated
[When vehicle speed is
approx. 40 km/h (25 MPH)]NOTE:
Maximum voltage may be 12V
due to specifications (connected
units).
SKIA3361E
SKIA3362E
SKIA6649J